Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2017.10
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0084736 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1635/24  Rear Airbag Sensor LH Circuit Malfunction  


DESCRIPTION

The side collision sensor LH circuit (to determine deployment of the front seat airbag assembly LH, curtain shield airbag assembly LH and front seat outer belt assembly LH) is composed of the airbag ECU assembly, side airbag sensor assembly LH and No. 2 side airbag sensor assembly LH.

The No. 2 side airbag sensor assembly LH detects impacts to the vehicle and sends signals to the airbag ECU assembly to determine if the airbags should be deployed.

DTC B1635/24 is stored when a malfunction is detected in the No. 2 side airbag sensor assembly LH.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1635/24 Rear Airbag Sensor LH Circuit Malfunction
·

No. 2 side airbag sensor assembly LH malfunction

·

Airbag ECU assembly malfunction


·

No. 2 side airbag sensor assembly LH

·

Airbag ECU assembly


Does not apply to test/check mode

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly LH


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Interchange the No. 2 side airbag sensor assembly LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1630/23 and B1635/24 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1635/24 is output. A
DTC B1630/23 is output. B
DTCs B1630/23 and B1635/24 are not output. C


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the No. 2 side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

REPLACE NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH

C