Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2017.10
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0084736 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1820/55  Short in Side Squib RH Circuit  B1821/55  Open in Side Squib RH Circuit  B1822/55  Short to GND in Side Squib RH Circuit  B1823/55  Short to B+ in Side Squib RH Circuit  


DESCRIPTION

The side squib RH circuit consists of the airbag ECU assembly and front seat airbag assembly RH.

The airbag ECU assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the side squib RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1820/55 Short in Side Squib RH Circuit
·

The airbag ECU assembly detects a line short in the side squib RH circuit during primary check.

·

Side squib RH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Front seat airbag assembly RH (Side squib RH)

·

Airbag ECU assembly


Applies to check mode
B1821/55 Open in Side Squib RH Circuit
·

The airbag ECU assembly detects an open in the side squib RH circuit.

·

Side squib RH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Front seat airbag assembly RH (Side squib RH)

·

Airbag ECU assembly


Applies to check mode
B1822/55 Short to GND in Side Squib RH Circuit
·

The airbag ECU assembly detects a short to ground in the side squib RH circuit.

·

Side squib RH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Front seat airbag assembly RH (Side squib RH)

·

Airbag ECU assembly


Applies to check mode
B1823/55 Short to B+ in Side Squib RH Circuit
·

The airbag ECU assembly detects a short to B+ in the side squib RH circuit.

·

Side squib RH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Front seat airbag assembly RH (Side squib RH)

·

Airbag ECU assembly


Applies to check mode

WIRING DIAGRAM

C381305E20
1.958,1.073 2.573,1.271 0.615,0.198 10 false SFR+ 4.75,1.156 5.365,1.354 0.615,0.198 10 false SFR+ 2.406,1.073 2.573,1.281 0.167,0.208 10 false 1 4.51,1.031 4.677,1.24 0.167,0.208 10 false 7 4.5,1.896 4.667,2.104 0.167,0.208 10 false 6 2.448,1.906 2.615,2.115 0.167,0.208 10 false 2 1.969,1.896 2.583,2.094 0.615,0.198 10 false SFR- 4.75,2.01 5.365,2.208 0.615,0.198 10 false SFR- 0.583,2.521 1.198,2.719 0.615,0.198 10 false F149 0.573,2.698 2.573,3.188 2,0.49 10 false Front Seat Airbag Assembly RH (Side Squib RH) 4.76,3.042 5.375,3.24 0.615,0.198 10 false F120 4.74,3.208 6.594,3.448 1.854,0.24 10 false Airbag ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTORS
a.
C238348C10
0.5,1.198 0.667,0.698 false 1.333,1.198 1.5,0.698 false 0.656,1.188 1.052,1.438 0.396,0.25 10 false D 1.031,1.188 1.354,1.427 0.323,0.24 10 false C 1.604,1.188 1.938,1.552 0.333,0.365 10 false B 1.99,1.188 2.333,1.542 0.344,0.354 10 false A 2.438,0.896 2.75,1.208 0.313,0.313 10 false *2 0.74,0.583 1,0.833 0.26,0.25 10 false *1 1.583,0.604 1.854,0.896 0.271,0.292 10 false *3
*1 Front Seat Airbag Assembly RH
*2 Airbag ECU Assembly
*3 Instrument Panel Wire


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front seat airbag assembly RH and airbag ECU assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat airbag assembly RH and airbag ECU assembly.


e.

Check that the terminals of connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the short spring for the instrument panel wire with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT SEAT AIRBAG ASSEMBLY RH (SIDE SQUIB RH)

NG

REPLACE INSTRUMENT PANEL WIRE

2.CHECK FRONT SEAT AIRBAG ASSEMBLY RH (SIDE SQUIB RH)
a.
C290010C37
0.333,2.333 0.833,2.583 0.5,0.25 2.208,2.458 2.458,2.458 false 0.417,0.396 0.583,0.896 false 2.49,2.385 2.948,2.583 0.458,0.198 10 false SST 0.417,2.365 0.813,2.719 0.396,0.354 10 false F149 0.344,1.615 0.74,1.969 0.396,0.354 10 false *a 0.229,0.313 0.625,0.667 0.396,0.354 10 false *1 2.5,0.583 2.896,0.938 0.396,0.354 10 false *2 0.719,0.896 1.115,1.25 0.396,0.354 10 false D 1.104,0.896 1.5,1.25 0.396,0.354 10 false C 1.854,0.896 2.25,1.25 0.396,0.354 10 false B 2.021,0.896 2.417,1.25 0.396,0.354 10 false A
*1 Front Seat Airbag Assembly RH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Seat Airbag Assembly RH)


Connect the connector to the airbag ECU assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the front seat airbag assembly RH (side squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1820/55, B1821/55, B1822/55 or B1823/55 is not output.


HINT:

Codes other than DTCs B1820/55, B1821/55, B1822/55 and B1823/55 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.


Result:
Proceed to
OK
NG



OK

NG

3.CHECK INSTRUMENT PANEL WIRE
3.CHECK INSTRUMENT PANEL WIRE
a.
C238257C72
0.333,2.406 0.833,2.667 0.5,0.26 1.292,2.688 1,2.927 true 1.781,2.927 1.49,2.688 true 0.708,1.083 0.5,0.583 false 1.417,1.083 1.208,0.583 false 0.833,1.073 1.146,1.323 0.313,0.25 10 false D 1.146,1.073 1.49,1.427 0.344,0.354 10 false C 1.604,1.073 1.875,1.354 0.271,0.281 10 false B 1.906,1.073 2.24,1.396 0.333,0.323 10 false A 2.313,0.792 2.656,1.135 0.344,0.344 10 false *2 0.323,0.479 0.604,0.719 0.281,0.24 10 false *1 0.219,1.813 0.51,2.104 0.292,0.292 10 false *a 1.74,2.938 2.188,3.167 0.448,0.229 10 false SFR- 0.729,2.927 1.292,3.25 0.563,0.323 10 false SFR+ 1.042,0.479 1.406,0.771 0.365,0.292 10 false *3 0.406,2.458 0.844,2.729 0.438,0.271 10 false F149
*1 Front Seat Airbag Assembly RH
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Front Seat Airbag Assembly RH)


Disconnect the instrument panel wire from the airbag ECU assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F149-1 (SFR+) - Body ground Ignition switch ON Below 1 V
F149-2 (SFR-) - Body ground Ignition switch ON Below 1 V



iv.

Turn the ignition switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F149-1 (SFR+) - F149-2 (SFR-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F149-1 (SFR+) - Body ground Always 1 MΩ or higher
F149-2 (SFR-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F149-1 (SFR+) - F149-2 (SFR-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK DTC
a.
C238241C30
0.833,1.292 0.583,0.844 false 0.417,0.76 0.75,1.063 0.333,0.302 10 false *1 0.979,1.302 1.156,1.531 0.177,0.229 10 false D 1.135,1.302 1.344,1.5 0.208,0.198 10 false C 1.583,1.302 1.781,1.5 0.198,0.198 10 false B 1.74,1.302 1.938,1.542 0.198,0.24 10 false A 2.146,1.021 2.438,1.26 0.292,0.24 10 false *2
*1 Front Seat Airbag Assembly RH
*2 Airbag ECU Assembly


Connect the connectors to the front seat airbag assembly RH and airbag ECU assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1820/55, B1821/55, B1822/55 or B1823/55 is not output.


HINT:

Codes other than DTCs B1820/55, B1821/55, B1822/55 and B1823/55 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG