Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function) › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090849 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  Driver Side Door Entry Lock and Unlock Functions do not Operate  


DESCRIPTION

for TMMIN Made:

If the entry lock and unlock functions do not operate for the driver door only, the request code may not be being transmitted from the No. 1 indoor electrical key antenna assembly (center pillar LH) or the trigger switch on the front door outside handle assembly (for driver door) may be malfunctioning. If the wireless door lock functions operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (center pillar LH)), or there may be wave interference.


for TMT Made:

If the entry lock and unlock functions do not operate for the driver door only, the request code may not be being transmitted front door outside handle assembly (for driver door) may be malfunctioning. If the wireless door lock functions operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door)), or there may be wave interference.


WIRING DIAGRAM

for TMMIN Made


B342593E17
1.75,2.323 2.063,2.521 0.313,0.198 10 false 10 3.01,0.531 3.323,0.729 0.313,0.198 10 false 4 2.969,1.885 3.281,2.083 0.313,0.198 10 false 31 2.969,2.333 3.281,2.531 0.313,0.198 10 false 30 4.5,0.594 4.813,0.792 0.313,0.198 10 false 3 5.76,0.594 6.073,0.792 0.313,0.198 10 false 1 4.5,2.417 4.813,2.615 0.313,0.198 10 false 3 4.49,1.979 4.802,2.177 0.313,0.198 10 false 1 1.719,2.51 2.177,2.708 0.458,0.198 10 false F43 2.938,0.708 3.396,0.906 0.458,0.198 10 false F43 2.938,2.073 3.396,2.271 0.458,0.198 10 false F44 2.938,2.51 3.396,2.708 0.458,0.198 10 false F44 1.729,3.031 3.365,3.479 1.635,0.448 10 false Certification ECU (Smart Key ECU Assembly) 2.469,0.698 3.083,0.896 0.615,0.198 10 false TSW1 2.479,2.073 3.094,2.271 0.615,0.198 10 false CLG1 2.479,2.51 3.094,2.708 0.615,0.198 10 false CG1B 2.042,2.51 2.24,2.719 0.198,0.208 10 false E 4.656,0.698 5.271,0.896 0.615,0.198 10 false TRG+ 5.365,0.698 5.979,0.896 0.615,0.198 10 false TRG- 4.667,2.063 5.281,2.26 0.615,0.198 10 false ANTE1 4.667,2.5 5.281,2.698 0.615,0.198 10 false CLGB 4.375,1.125 4.833,1.323 0.458,0.198 10 false H9 4.375,1.271 6.01,1.677 1.635,0.406 10 false Front Door Outside Handle Assembly LH 4.177,2.99 6.406,3.323 2.229,0.333 10 false No. 1 Indoor Electrical Key Antenna Assembly (Center Pillar LH) 4.156,2.833 4.615,3.031 0.458,0.198 10 false F49


for TMT Made


E374148E05
1.76,3.063 3.292,3.531 1.531,0.469 10 false Certification ECU (Smart Key ECU Assembly) 4.365,2.042 6.021,2.542 1.656,0.5 10 false Front Door Outside Handle Assembly LH 2.948,1.094 3.406,1.292 0.458,0.198 10 false F44 2.948,1.521 3.406,1.719 0.458,0.198 10 false F44 4.365,1.865 4.823,2.063 0.458,0.198 10 false H12 2.948,0.656 3.406,0.854 0.458,0.198 10 false F43 1.729,2.51 2.188,2.708 0.458,0.198 10 false F43 2.052,2.5 2.51,2.698 0.458,0.198 10 false E 1.75,2.323 2.208,2.521 0.458,0.198 10 false 10 4.479,0.542 4.938,0.74 0.458,0.198 10 false 1 3.021,0.917 3.479,1.115 0.458,0.198 10 false 9 2.99,1.344 3.448,1.542 0.458,0.198 10 false 25 2.469,0.656 2.927,0.854 0.458,0.198 10 false TSW1 2.49,1.094 2.948,1.292 0.458,0.198 10 false CLG5 2.49,1.51 2.948,1.708 0.458,0.198 10 false CG5B 4.688,0.646 5.146,0.844 0.458,0.198 10 false TRG+ 4.698,1.083 5.156,1.281 0.458,0.198 10 false ANT1 4.698,1.531 5.156,1.729 0.458,0.198 10 false ANT2 5.354,1.49 5.813,1.688 0.458,0.198 10 false TRG- 3.01,0.479 3.469,0.677 0.458,0.198 10 false 4 4.479,0.979 4.938,1.177 0.458,0.198 10 false 3 4.479,1.417 4.938,1.615 0.458,0.198 10 false 6 5.792,1.365 6.25,1.563 0.458,0.198 10 false 4 0.125,0.125 1.271,0.396 1.146,0.271 12 false for LHD:

E374148E06
1.76,3.063 3.292,3.531 1.531,0.469 10 false Certification ECU (Smart Key ECU Assembly) 4.365,2.042 6.021,2.542 1.656,0.5 10 false Front Door Outside Handle Assembly RH 2.948,1.094 3.406,1.292 0.458,0.198 10 false F44 2.948,1.521 3.406,1.719 0.458,0.198 10 false F44 4.365,1.865 4.823,2.063 0.458,0.198 10 false G12 2.948,0.656 3.406,0.854 0.458,0.198 10 false F43 1.729,2.51 2.188,2.708 0.458,0.198 10 false F43 2.052,2.5 2.51,2.698 0.458,0.198 10 false E 1.75,2.323 2.208,2.521 0.458,0.198 10 false 10 4.479,0.542 4.938,0.74 0.458,0.198 10 false 1 3.021,0.917 3.479,1.115 0.458,0.198 10 false 9 2.99,1.344 3.448,1.542 0.458,0.198 10 false 25 2.469,0.656 2.927,0.854 0.458,0.198 10 false TSW1 2.49,1.094 2.948,1.292 0.458,0.198 10 false CLG5 2.49,1.51 2.948,1.708 0.458,0.198 10 false CG5B 4.688,0.646 5.146,0.844 0.458,0.198 10 false TRG+ 4.698,1.083 5.156,1.281 0.458,0.198 10 false ANT1 4.698,1.531 5.156,1.729 0.458,0.198 10 false ANT2 5.354,1.49 5.813,1.688 0.458,0.198 10 false TRG- 3.01,0.479 3.469,0.677 0.458,0.198 10 false 4 4.479,0.979 4.938,1.177 0.458,0.198 10 false 3 4.479,1.417 4.938,1.615 0.458,0.198 10 false 6 5.792,1.365 6.25,1.563 0.458,0.198 10 false 4 0.135,0.104 1.24,0.542 1.104,0.438 12 false for RHD:


CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) or B27B0 is not output.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".



PROCEDURE

1.SYSTEM CHECK
a.

Check the vehicle specifications.


Result:
Result Proceed to
for TMMIN Made A
for TMT Made B



A

2.CHECK POWER DOOR LOCK CONTROL SYSTEM

B

13.CHECK POWER DOOR LOCK CONTROL SYSTEM
2.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the power window regulator master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

3.CHECK DTC OUTPUT

NG

3.CHECK DTC OUTPUT
a.

Check the DTCs

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B27A1 is not output.



Result:
Proceed to
OK
NG



OK

4.CHECK WAVE ENVIRONMENT

NG

4.CHECK WAVE ENVIRONMENT
a.
B359383C22
2.177,1.052 2.49,1.25 0.313,0.198 10 false *a
*a Approximately 0.3 m (0.984 ft.)


Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly (for driver door) and perform an entry function check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the door handle, communication may not be possible.


HINT:

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

5.READ VALUE USING GTS (D-DOOR TRIGGER SWITCH)

B

AFFECTED BY WAVE INTERFERENCE

5.READ VALUE USING GTS (D-DOOR TRIGGER SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry & Start / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D-Door Trigger Switch Driver door trigger switch ON or OFF ON: Driver door trigger switch pressed
OFF: Driver door trigger switch not pressed
·

Displays whether the trigger switch is on or off (even if the trigger switch is pressed and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a trigger switch malfunction when the entry lock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
D-Door Trigger Switch
50003 125 12
OK:

On the GTS screen, the display changes between ON and OFF as shown in the table above.



Result:
Proceed to
OK
NG



OK

6.CHECK KEY DIAGNOSTIC MODE

NG

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH))
6.CHECK KEY DIAGNOSTIC MODE
B359383C25
2.177,1.052 2.49,1.25 0.313,0.198 10 false *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


a.

Check the following antennas in key diagnostic mode.


b.

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

HINT:

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.


i.

Check the No. 1 indoor electrical key antenna assembly (center pillar LH):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143


Result:
Result Proceed to
Wireless door lock buzzer does not sounds A
Wireless door lock buzzer sounds B



A

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (CENTER PILLAR LH))

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (CENTER PILLAR LH))
a.

Disconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the F49 No. 1 indoor electrical key antenna assembly (center pillar LH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-31 (CLG1) - F49-1 (ANTE1) Always Below 1 Ω
F44-30 (CG1B) - F49-3 (CLGB) Always Below 1 Ω
F43-10 (E) - Body ground Always Below 1 Ω
F44-31 (CLG1) or F49-1 (ANTE1) - Body ground Always 10 kΩ or higher
F44-30 (CG1B) or F49-3 (CLGB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (CENTER PILLAR LH))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (CENTER PILLAR LH))
a.

Connect the F43 and F44 certification ECU (smart key ECU assembly) connectors.


b.

Connect the F49 No. 1 indoor electrical key antenna assembly (center pillar LH) connector.


c.

Using an oscilloscope, check the waveform.

B345002C05
0.844,1.198 1.292,1.448 0.448,0.25 4.208,2.281 4.438,1.458 true 1.49,2.219 1.719,1.396 true 2.073,2.229 1.854,1.406 true 0.948,1.24 1.406,1.438 0.458,0.198 10 false F49 1.135,0.688 1.448,0.885 0.313,0.198 10 false *a 3.531,0.469 3.844,0.667 0.313,0.198 10 false *b 3.479,1.302 3.938,1.5 0.458,0.198 10 false GND 4.115,2.323 4.427,2.521 0.313,0.198 10 false *c 1.313,2.271 1.75,2.469 0.438,0.198 10 false CLGB 1.906,2.271 2.458,2.469 0.552,0.198 10 false ANTE1
*a Component with harness connected
(No. 1 Indoor Electrical Key Antenna Assembly (Center Pillar LH))
*b Waveform 1
*c Trigger switch ON - -


OK:
Tester Connection Condition Tool Setting Specified Condition
F49-1 (ANTE1) - F49-3 (CLGB) Procedure:
1.

Engine switch off

2.

All doors closed


- Not pulse generation
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Press the trigger switch on the front door outside handle assembly (for driver door)


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Result Proceed to
NG A
OK B



A

9.CHECK ENTRY DOOR LOCK OPERATION

B

REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (CENTER PILLAR LH)

9.CHECK ENTRY DOOR LOCK OPERATION
a.

Check the operation of the entry lock/unlock function.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:

Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (center pillar LH) before performing the inspection.


OK:

Entry lock/unlock operate normally.


Result:
Proceed to
OK
NG




OK

END (CONNECT CONNECTORS PROPERLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH))
a.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the H9 front door outside handle assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-4 (TSW1) - H9-3 (TRG+) Always Below 1 Ω
F43-10 (E) - Body ground Always Below 1 Ω
H9-1 (TRG-) - Body ground Always Below 1 Ω
F43-4 (TSW1) or H9-3 (TRG+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH
a.

Remove the front door outside handle assembly LH.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY LOCK AND UNLOCK SWITCH>REMOVAL


b.

Inspect the front door outside handle assembly LH.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY LOCK AND UNLOCK SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

12.CHECK ENTRY DOOR LOCK OPERATION

NG

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

12.CHECK ENTRY DOOR LOCK OPERATION
a.

Check the operation of the entry lock/unlock function.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:

Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) before performing the inspection.


OK:

Entry lock/unlock operate normally.


Result:
Proceed to
OK
NG




OK

END (CONNECT CONNECTORS PROPERLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

13.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the power window regulator master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

14.CHECK DTC OUTPUT

NG

14.CHECK DTC OUTPUT
a.

Check the DTCs

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B27A1 is not output.



Result:
Proceed to
OK
NG



OK

15.CHECK WAVE ENVIRONMENT

NG

15.CHECK WAVE ENVIRONMENT
a.
B354279C11
0.125,0.271 0.438,0.5 0.313,0.229 12 false *A 0.135,2.74 0.448,2.958 0.313,0.219 12 false *B 2.083,1.542 2.396,1.698 0.313,0.156 10 false *a 1.542,3.719 1.854,3.875 0.313,0.156 10 false *a
*A for LHD
*B for RHD
*a Approximately 0.3 m (0.984 ft.)


Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly (for driver door) and perform an entry function check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the door handle, communication may not be possible.


HINT:

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



Result:
Result Proceed to
Entry function does not operate normally. A
Entry function operates normally. B



A

16.READ VALUE USING GTS (D-DOOR TRIGGER SWITCH)

B

AFFECTED BY WAVE INTERFERENCE

16.READ VALUE USING GTS (D-DOOR TRIGGER SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry & Start / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D-Door Trigger Switch Driver door trigger switch ON or OFF ON: Driver door trigger switch pressed
OFF: Driver door trigger switch not pressed
·

Displays whether the trigger switch is on or off (even if the trigger switch is pressed and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a trigger switch malfunction when the entry lock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
D-Door Trigger Switch
50003 125 12
OK:

On the GTS screen, the display changes between ON and OFF as shown in the table above.



Result:
Proceed to
OK
NG



OK

17.CHECK KEY DIAGNOSTIC MODE

NG

21.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR))
17.CHECK KEY DIAGNOSTIC MODE
B354279C12
0.125,0.271 0.438,0.5 0.313,0.229 12 false *A 0.135,2.74 0.448,2.958 0.313,0.219 12 false *B 2.083,1.542 2.396,1.698 0.313,0.156 10 false *a 1.542,3.719 1.854,3.875 0.313,0.156 10 false *a
*A for LHD
*B for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


a.

Check the following antennas in key diagnostic mode.


b.

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

HINT:

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.


i.

Check the electrical key antenna (for driver door)

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143


Result:
Result Proceed to
Wireless door lock buzzer does not sound A
Wireless door lock buzzer sounds B



A

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR))

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR))
a.

Disconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.


b.

for LHD:

i.

Disconnect the H12 front door outside handle assembly LH connector.



c.

for RHD:

i.

Disconnect the G12 front door outside handle assembly RH connector.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F44-9 (CLG5) - H12-3 (ANT1) Always Below 1 Ω
F44-25 (CG5B) - H12-6 (ANT2) Always Below 1 Ω
F43-10 (E) - Body ground Always Below 1 Ω
F44-9 (CLG5) or H12-3 (ANT1) - Body ground Always 10 kΩ or higher
F44-25 (CG5B) or H12-6 (ANT2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F44-9 (CLG5) - G12-3 (ANT1) Always Below 1 Ω
F44-25 (CG5B) - G12-6 (ANT2) Always Below 1 Ω
F43-10 (E) - Body ground Always Below 1 Ω
F44-9 (CLG5) or G12-3 (ANT1) - Body ground Always 10 kΩ or higher
F44-25 (CG5B) or G12-6 (ANT2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR))
a.

Connect the F43 and F44 certification ECU (smart key ECU assembly) connectors.


b.

for LHD:

i.

Connect the H12 front door outside handle assembly LH connector.



c.

for RHD:

i.

Connect the G12 front door outside handle assembly RH connector.



d.

Using an oscilloscope, check the waveform.

E374150C10
2.49,0.5 3,0.75 0.51,0.25 4.573,0.5 5.083,0.75 0.51,0.25 1.875,2.542 2.229,1.552 true 2.917,4.458 3.302,3.76 true 5.438,2.583 5.052,1.531 true 0.531,0.552 0.875,0.771 0.344,0.219 10 false *a 2.615,2.979 3.052,3.271 0.438,0.292 10 false *b 2.76,4.458 3.115,4.646 0.354,0.188 10 false *c 2.604,0.552 3.031,0.802 0.427,0.25 10 false F43 4.688,0.542 5.313,0.771 0.625,0.229 10 false F44 2.375,3.635 2.792,3.844 0.417,0.208 10 false GND 1.792,2.573 2.135,2.792 0.344,0.219 10 false E 5.406,2.625 6.24,3.063 0.833,0.438 10 false CLG5
*a Component with harness connected
Certification ECU (Smart Key ECU Assembly)
*b Waveform 1
*c Trigger switch ON - -


OK:
Tester Connection Condition Tool Setting Specified Condition
F44-9 (CLG5) - F43-10 (E) Procedure:
1.

Engine switch off

2.

All doors closed


- Not pulse generation
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Press the trigger switch on the front door outside handle assembly (for driver door)


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

20.CHECK ENTRY DOOR LOCK OPERATION

NG

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR)

20.CHECK ENTRY DOOR LOCK OPERATION
a.

Check the operation of the entry lock/unlock function.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:

Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly) and front door outside handle assembly LH or RH before performing the inspection.


OK:

Entry lock/unlock operate normally.


Result:
Proceed to
OK
NG




OK

END (CONNECT CONNECTORS PROPERLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

21.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR))
a.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


b.

for LHD:

i.

Disconnect the H12 front door outside handle assembly LH connector.



c.

for RHD:

i.

Disconnect the G12 front door outside handle assembly RH connector.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F43-4 (TSW1) - H12-1 (TRG+) Always Below 1 Ω
F43-10 (E) - Body ground Always Below 1 Ω
H12-4 (TRG-) - Body ground Always Below 1 Ω
F43-4 (TSW1) or H12-1 (TRG+) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F43-4 (TSW1) - G12-1 (TRG+) Always Below 1 Ω
F43-10 (E) - Body ground Always Below 1 Ω
G12-4 (TRG-) - Body ground Always Below 1 Ω
F43-4 (TSW1) or G12-1 (TRG+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

22.INSPECT FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.INSPECT FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR)
a.

Remove the front door outside handle assembly (for driver door).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY LOCK AND UNLOCK SWITCH>REMOVAL


b.

Inspect the front door outside handle assembly (for driver door).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY LOCK AND UNLOCK SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

23.CHECK ENTRY DOOR LOCK OPERATION

NG

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR)

23.CHECK ENTRY DOOR LOCK OPERATION
a.

Check the operation of the entry lock/unlock function.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:

Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) before performing the inspection.


OK:

Entry lock/unlock operate normally.


Result:
Proceed to
OK
NG




OK

END (CONNECT CONNECTORS PROPERLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)