Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function) › from 2017.10
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090849 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  Back Door Entry Lock and Unlock Functions do not Operate  


DESCRIPTION

If the entry lock and unlock functions do not operate for the back door only, the request code may not be being transmitted from the electrical key antenna (outside luggage compartment), or the back door opener switch assembly may be malfunctioning. If the wireless door lock functions operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage compartment)), or there may be wave interference.

WIRING DIAGRAM

E374149E04
4.74,3.781 6.292,4.281 1.552,0.5 10 false Certification ECU (Smart Key ECU Assembly) 5.76,3.25 6.219,3.448 0.458,0.198 10 false E 4.979,0.875 5.438,1.073 0.458,0.198 10 false CLG7 4.979,1.313 5.438,1.51 0.458,0.198 10 false CG7B 4.969,2.813 5.427,3.01 0.458,0.198 10 false TSW5 4.979,3.25 5.438,3.448 0.458,0.198 10 false TSW6 6,3.031 6.458,3.229 0.458,0.198 10 false 10 2.396,2.698 2.854,2.896 0.458,0.198 10 false 3 4.677,3.042 5.135,3.24 0.458,0.198 10 false 23 4.677,0.656 5.135,0.854 0.458,0.198 10 false 28 4.677,1.094 5.135,1.292 0.458,0.198 10 false 29 1.188,3.552 1.646,3.75 0.458,0.198 10 false R8 1.177,3.729 2.344,4.208 1.167,0.479 10 false Back Door Opener Switch Assembly 1.146,1.615 1.604,1.813 0.458,0.198 10 false F152 1.135,1.792 3.115,2.292 1.979,0.5 10 false Electrical Key Antenna (Outside Luggage Compartment) 4.677,2.625 5.135,2.823 0.458,0.198 10 false 14 2.396,3.104 2.854,3.302 0.458,0.198 10 false 1 1.083,3.135 1.542,3.333 0.458,0.198 10 false 2 1.896,1.292 2.354,1.49 0.458,0.198 10 false CLGB 1.844,0.865 2.302,1.063 0.458,0.198 10 false ANTE7 2.406,0.75 2.865,0.948 0.458,0.198 10 false 2 2.396,1.177 2.854,1.375 0.458,0.198 10 false 1 5.958,3.229 6.26,3.438 0.302,0.208 10 false F43 4.625,2.802 4.927,3.01 0.302,0.208 10 false F43 4.635,3.229 4.938,3.438 0.302,0.208 10 false F43 4.625,0.854 4.927,1.063 0.302,0.208 10 false F44 4.625,1.292 4.927,1.5 0.302,0.208 10 false F44 1.281,3.115 1.74,3.313 0.458,0.198 10 false E 2.177,3.115 2.635,3.313 0.458,0.198 10 false L 2.115,2.719 2.573,2.917 0.458,0.198 10 false UL

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) or B27B0 is not output.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the power window regulator master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

2.CHECK DTC OUTPUT

NG

2.CHECK DTC OUTPUT
a.

Check the DTCs

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B27A8 is not output.



Result:
Proceed to
OK
NG



OK

3.CHECK WAVE ENVIRONMENT

NG

3.CHECK WAVE ENVIRONMENT
a.
B345011C05
1.802,1.281 2.115,1.438 0.313,0.156 10 false *a
*a Approximately 0.3 m (0.984 ft.)


Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the electrical key antenna (outside luggage compartment) and perform an entry back door unlock / lock function check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

NOTICE:

If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the rear bumper, communication may not be possible.


HINT:

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



Result:
Result Proceed to
Entry function does not operate normally. A
Entry function operates normally. B



A

4.READ VALUE USING GTS (TR/B-DOOR UNLOCK SW, TR/B-DOOR LOCK SW)

B

AFFECTED BY WAVE INTERFERENCE

4.READ VALUE USING GTS (TR/B-DOOR UNLOCK SW, TR/B-DOOR LOCK SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry & Start / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tr/B-Door Lock SW Back door opener switch assembly (lock switch) ON or OFF ON: Back door opener switch assembly (lock switch) pushed
OFF: Back door opener switch assembly (lock switch) not pushed
·

Displays whether the back door opener switch assembly (lock switch) is on or off.

·

Use this Data List item to help determine if there is a switch malfunction when the back door open function does not operate.


Tr/B-Door Unlock SW Back door opener switch assembly (unlock switch) ON or OFF ON: Back door opener switch assembly (unlock switch) pushed
OFF: Back door opener switch assembly (unlock switch) not pushed
·

Displays whether the back door opener switch assembly (unlock switch) is on or off.

·

Use this Data List item to help determine if there is a switch malfunction when the luggage compartment door open function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
Tr/B-Door Lock SW
Tr/B-Door Unlock SW
50003 125 16,17
OK:

On the GTS screen, the display changes between ON and OFF as shown in the table above.



Result:
Proceed to
OK
NG



OK

5.CHECK KEY DIAGNOSTIC MODE

NG

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BACK DOOR OPENER SWITCH ASSEMBLY)
5.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antennas in key diagnostic mode.


b.

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

HINT:

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.


i.
B345011C05
1.802,1.281 2.115,1.438 0.313,0.156 10 false *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (outside luggage compartment):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage compartment), check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143


Result:
Result Proceed to
Wireless door lock buzzer does not sounds A
Wireless door lock buzzer sounds B



A

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))
a.

Disconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the F152 electrical key antenna (outside luggage compartment) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-28 (CLG7) - F152-2 (ANTE7) Always Below 1 Ω
F44-29 (CG7B) - F152-1 (CLGB) Always Below 1 Ω
F43-10 (E) - Body ground Always Below 1 Ω
F44-28 (CLG7) or F152-2 (ANTE7) - Body ground Always 10 kΩ or higher
F44-29 (CG7B) or F152-1 (CLGB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))
a.

Connect the F43 and F44 certification ECU (smart key ECU assembly) connectors.


b.

Connect the F152 electrical key antenna (outside luggage compartment) connector.


c.

Using an oscilloscope, check the waveform.

E374150C05
2.49,0.5 3,0.75 0.51,0.25 4.573,0.5 5.083,0.75 0.51,0.25 1.875,2.542 2.229,1.552 true 2.917,4.458 3.302,3.76 true 5.396,2.646 4.896,1.635 true 4.542,2.656 4.833,1.635 true 0.531,0.552 0.875,0.771 0.344,0.219 10 false *a 2.615,2.979 3.052,3.271 0.438,0.292 10 false *b 2.76,4.458 3.115,4.646 0.354,0.188 10 false *c 2.615,0.552 2.958,0.771 0.344,0.219 10 false F43 4.698,0.542 5.042,0.76 0.344,0.219 10 false F44 2.375,3.635 2.792,3.844 0.417,0.208 10 false GND 1.792,2.573 2.135,2.792 0.344,0.219 10 false E 5.26,2.698 6.094,3.135 0.833,0.438 10 false CLG7 4.354,2.698 5.188,3.135 0.833,0.438 10 false CG7B
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly)
*b Waveform 1
*c Back door opener switch assembly on - -


OK:
Tester Connection Condition Tool Setting Specified Condition
F44-28 (CLG7) - F43-10 (E) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Back door opener switch assembly off → on


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)
F44-29 (CG7B) - F43-10 (E) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Back door opener switch assembly off → on


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to Proceed to
NG A
OK B



A

8.CHECK ENTRY BACK DOOR OPERATION

B

8.CHECK ENTRY BACK DOOR OPERATION
a.

Check the operation of the entry back door lock/unlock function.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:

Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage compartment) before performing the inspection.


OK:

Entry back door lock/unlock operate normally.


Result:
Proceed to
OK
NG




OK

END (CONNECT CONNECTORS PROPERLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BACK DOOR OPENER SWITCH ASSEMBLY)
a.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the R8 back door opener switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-14 (TSW5) - R8-3 (UL) Always Below 1 Ω
F43-23 (TSW6) - R8-1 (L) Always Below 1 Ω
F43-10 (E) - Body ground Always Below 1 Ω
R8-2 (E) - Body ground Always Below 1 Ω
F43-14 (TSW5) or R8-3 (UL) - Body ground Always 10 kΩ or higher
F43-23 (TSW6) or R8-1 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY
a.

Remove the back door opener switch assembly.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>INSPECTION


b.

Inspect the back door opener switch assembly.

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>REMOVAL


Result:
Proceed to
OK
NG



OK

11.CHECK ENTRY BACK DOOR OPERATION

NG

REPLACE BACK DOOR OPENER SWITCH ASSEMBLY

11.CHECK ENTRY BACK DOOR OPERATION
a.

Check the operation of the entry back door lock/unlock function.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:

Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly) and back door opener switch assembly before performing the inspection.


OK:

Entry back door lock/unlock operate normally.


Result:
Proceed to
OK
NG




OK

END (CONNECT CONNECTORS PROPERLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)