Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017113 METER / GAUGE / DISPLAY _0087658 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Malfunction in Water Temperature Warning Light  


DESCRIPTION

In this circuit, the combination meter assembly receives engine coolant temperature signals from the ECM using the CAN communication system (CAN V Bus). The combination meter assembly displays engine coolant temperature that is calculated based on the data received from the ECM.

WIRING DIAGRAM

E255800E29
4.74,2.563 6.958,2.813 2.219,0.25 10 false Combination Meter Assembly 1.771,2.573 3.01,2.958 1.24,0.385 10 false ECM 0.802,3.375 3.563,3.656 2.76,0.281 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


HINT:

If there is an open or short in the engine coolant temperature sensor circuit, the ECM stores DTCs. Troubleshoot the SFI system.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication DTCs are not output. A
CAN communication DTCs are output. B



A

2.PERFORM ACTIVE TEST USING GTS (COOLANT TEMP)

B

2.PERFORM ACTIVE TEST USING GTS (COOLANT TEMP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

According to the display on the GTS, perform the Active Test.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Indicat. Lamp Coolant Cool Water temperature cool indicator light OFF or ON -
Indicat. Lamp Coolant Hot Water temperature hot warning light OFF or ON -
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Lamp Coolant Cool
50004 122 17
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Lamp Coolant Hot
50004 122 18
OK:

Value selected during Active Test is displayed.



Result:
Result Proceed to
OK A
NG (for TMMIN Made) B
NG (for TMT Made) C



A

3.READ VALUE USING GTS (COOLANT TEMPERATURE)

B

C

3.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List


e.

According to the display on the GTS, read the Data List.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Coolant Temperature Engine coolant temperature Min.: 0°C (32°F), Max.: 127.5°C (261.5°F) 75 to 100°C (167 to 212°F): After warming up -
Body Electrical > Combination Meter > Data List
Tester Display
Coolant Temperature
50003 122 10
OK:

Vehicle's coolant temperature and tester value are the same.



Result:
Result Proceed to
OK A
NG (for TMMIN Made) B
NG (for TMT Made) C



A

4.CHECK FOR DTC

B

C

4.CHECK FOR DTC

Result:
Result Proceed to
SFI system DTCs are not output. (for TMMIN Made) A
SFI system DTCs are not output. (for TMT Made) B
SFI system DTCs are output. (for 1NR-FE) C
SFI system DTCs are output. (for 2NR-FE) D



A

B

C

D