Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › from 2018.01
RM30M0E _58 Vehicle Interior _017118 HEATING / AIR CONDITIONING _0086573 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1412  Ambient Temperature Sensor Circuit  


DESCRIPTION

The thermistor assembly is installed in front of the cooler condenser assembly to detect the ambient temperature, which is used to control the air conditioning system. This sensor is connected to the combination meter assembly and detects fluctuations in the ambient temperature. This data is used for controlling the cabin temperature. The sensor sends a signal to the combination meter assembly. The resistance of the thermistor assembly changes in accordance with the ambient temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases. The combination meter assembly applies a voltage (5 V) to the thermistor assembly and reads voltage changes due to changes in the resistance of the thermistor assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1412 Ambient Temperature Sensor Circuit Open or short in thermistor assembly circuit
·

Thermistor assembly

·

Harness or connect or between thermistor assembly and combination meter assembly

·

Air conditioning amplifier assembly

·

Combination meter assembly

·

CAN communication system


Memorized
(4 seconds or more)*1

*1: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.


HINT:

If the ambient temperature is approximately -52.9°C (-63.22°F) or lower, DTC B1412 may be output even though the system is normal.


WIRING DIAGRAM

E371814E13
3.438,1.823 5.583,2.021 2.146,0.198 10 false CAN Controller 3.49,2.896 4.01,3.198 0.521,0.302 10 false 5V +B 3.552,3.635 4.073,3.938 0.521,0.302 10 false CAN I/F 3.844,0.594 4.365,0.896 0.521,0.302 10 false I/F 5.771,3.667 6.292,3.969 0.521,0.302 10 false TX+ 5.792,4.208 6.313,4.51 0.521,0.302 10 false TX- 4.615,4.052 5.135,4.354 0.521,0.302 10 false CANL 4.594,3.51 5.115,3.813 0.521,0.302 10 false CANH 0.51,1.281 0.969,1.479 0.458,0.198 10 false A25 0.5,1.458 2.073,1.865 1.573,0.406 10 false Thermistor Assembly 3.781,1.375 4.302,1.677 0.521,0.302 10 false CPU 2.948,4.885 5.563,5.427 2.615,0.542 10 false Combination Meter Assembly 5.635,4.656 6.094,4.854 0.458,0.198 10 false F3 5.604,4.833 7.156,5.479 1.552,0.646 10 false Air Conditioning Amplifier Assembly 2.823,0.448 3.344,0.75 0.521,0.302 10 false TX1+ 2.823,0.813 3.344,1.115 0.521,0.302 10 false TX1- 2.188,0.458 2.708,0.76 0.521,0.302 10 false 2 2.198,0.813 2.719,1.115 0.521,0.302 10 false 1 2.583,0.448 3.104,0.75 0.521,0.302 10 false 36 2.594,0.792 3.115,1.094 0.521,0.302 10 false 37 0.823,5.281 3.313,5.656 2.49,0.375 10 false : CAN Communication Line 5.052,3.51 5.573,3.813 0.521,0.302 10 false 23 5.042,4.042 5.563,4.344 0.521,0.302 10 false 22 5.552,3.5 6.063,3.802 0.51,0.302 10 false 11 5.552,4.052 6.063,4.354 0.51,0.302 10 false 12 2.969,4.656 3.427,4.854 0.458,0.198 10 false F38

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication DTCs are not output. A
CAN communication DTCs are output. B



A

2.READ VALUE USING GTS

B

2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Ambient Temp Sensor Thermistor assembly Min.: -23.30°C (-9.94°F)
Max.: 65.95°C (150.71°F)
Actual ambient temperature displayed -
Body Electrical > Air Conditioner > Data List
Tester Display
Ambient Temp Sensor
50003 121 2
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
OK (When troubleshooting according to Problem Symptoms Table) A
OK (When troubleshooting according to the DTC) B
NG C



A

B

3.CHECK FOR DTC

C

4.INSPECT THERMISTOR ASSEMBLY
3.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Clear DTCs
50002 121

b.

Check for DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

4.INSPECT THERMISTOR ASSEMBLY


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (THERMISTOR ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (THERMISTOR ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the A25 thermistor assembly connector.


b.

Disconnect the F38 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-36 (TX1+) - A25-2 Always Below 1 Ω
F38-37 (TX1-) - A25-1 Always Below 1 Ω
F38-36 (TX1+) or A25-2 - Body ground Always 10 kΩ or higher
F38-37 (TX1-) or A25-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR