Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › from 2018.01
RM30M0E _58 Vehicle Interior _017117 SEAT BELT _0084737 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Driver Side Seat Belt Warning Light does not Operate  


DESCRIPTION

When the ignition switch is ON, the combination meter assembly receives signals from the front seat inner belt assembly (Driver Side). When the seat belt is unfastened, the combination meter assembly flashes the driver side seat belt warning light in the combination meter assembly. When the seat belt is fastened, the combination meter assembly stops flashing the driver side seat belt warning light.

WIRING DIAGRAM

C380578E03
1.469,1.333 1.927,1.531 0.458,0.198 10 false F29 1.469,1.5 2.771,1.875 1.302,0.375 10 false Front Seat Inner Belt Assembly LH 1.375,0.875 1.583,1.094 0.208,0.219 10 false 2 2.438,0.875 2.646,1.094 0.208,0.219 10 false 3 4.26,0.875 4.469,1.094 0.208,0.219 10 false 5 4.417,0.969 4.875,1.167 0.458,0.198 10 false BKL 4.531,1.844 4.99,2.042 0.458,0.198 10 false F38 4.51,1.99 5.698,2.385 1.188,0.396 10 false Combination Meter Assembly 0.208,0.135 1.448,0.51 1.24,0.375 12 false for LHD:

C380578E04
1.469,1.354 1.927,1.552 0.458,0.198 10 false F114 1.469,1.521 2.771,1.896 1.302,0.375 10 false Front Seat Inner Belt Assembly RH 1.375,0.875 1.583,1.094 0.208,0.219 10 false 2 2.438,0.875 2.646,1.094 0.208,0.219 10 false 3 4.26,0.875 4.469,1.094 0.208,0.219 10 false 5 4.417,0.969 4.875,1.167 0.458,0.198 10 false BKL 4.583,1.865 5.042,2.063 0.458,0.198 10 false F38 4.573,2.021 5.76,2.417 1.188,0.396 10 false Combination Meter Assembly 0.26,0.146 1.448,0.542 1.188,0.396 12 false for RHD:


CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (DRIVER SIDE SEAT BELT)
a.

Connect the GTS DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Driver Side Seat Belt Front seat belt warning light OFF or ON Confirm that the vehicle is stopped with the engine idling
Body Electrical > Combination Meter > Active Test
Tester Display
Driver Side Seat Belt
50004 122 12
OK:

Front seat belt warning light condition can be switched by Active Test.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (DRIVER SIDE SEATBELT BUCKLE SWITCH)

NG

REPLACE COMBINATION METER ASSEMBLY

2.READ VALUE USING GTS (DRIVER SIDE SEATBELT BUCKLE SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Driver Side Seatbelt Buckle Switch Front seat belt buckle switch (Driver Side) OFF or ON OFF: Driver seat belt not fastened
ON: Driver seat belt fastened
-
Body Electrical > Combination Meter > Data List
Tester Display
Driver Side Seatbelt Buckle Switch
50003 122 119
OK:

ON or OFF appears on the GTS screen according to the driver seat belt condition.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

REPLACE COMBINATION METER ASSEMBLY

B

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH

C

5.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH
3.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH
a.

Remove the front seat inner belt assembly LH.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL


b.

Inspect the front seat inner belt assembly LH.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

4.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the F29 front seat inner belt assembly LH connector.


b.

Disconnect the F38 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-3 - F38-5 (BKL) Always Below 1 Ω
F29-3 or F38-5 (BKL) - Body ground Always 10 kΩ or higher
F29-2 - Body ground Always Below 1 Ω



d.

Reconnect the F38 combination meter assembly connector.


e.

Reconnect the F29 front seat inner belt assembly LH connector.


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH
a.

Remove the front seat inner belt assembly RH.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL


b.

Inspect the front seat inner belt assembly RH.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

INSPECT FRONT SEAT INNER BELT ASSEMBLY RH

6.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the F114 front seat inner belt assembly RH connector.


b.

Disconnect the F38 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F114-3 - F38-5 (BKL) Always Below 1 Ω
F114-3 or F38-5 (BKL) - Body ground Always 10 kΩ or higher
F114-2 - Body ground Always Below 1 Ω



d.

Reconnect the F38 combination meter assembly connector.


e.

Reconnect the F114 front seat inner belt assembly RH connector.


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR