When the rear window defogger switch on the air conditioning control assembly is pressed, the operation signal is transmitted to the air conditioning amplifier assembly via LIN communication. When the air conditioning amplifier assembly receives the signal, it turns on the defogger relay to operate the window defogger system.
Inspect the fuses for circuits related to this system before performing the following procedure.
Check the air conditioning system.
Both the window defogger system operation signal and air conditioning system operation signal are transmitted to the air conditioning amplifier assembly via the same communication line.
The air conditioning system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Defogger Relay (Rear) | DEF relay | OFF or ON | - |
| Tester Display |
|---|
| Defogger Relay (Rear) |
The window defogger system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air conditioning amplifier assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
Check that the window defogger system operates normally.
The window defogger system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the DEF relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the DEF relay.
| *1 | NO. 3 RELAY BLOCK |
| *a | DEF Relay Holder |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| DEF relay holder terminal 1 - Body ground | Ignition switch ON | 11 to 14 V |
| DEF relay holder terminal 5 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the DEF relay.
Disconnect the F3 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DEF relay holder terminal 2 - F3-38 (RDFG) | Always | Below 1 Ω |
| DEF relay holder terminal 2 - Body ground | Always | 10 kΩ or higher |
| F3-38 (RDFG) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
Reconnect the air conditioning amplifier assembly connector.
Reinstall the DEF relay.
Remove the air conditioning amplifier assembly with its connectors still connected.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F3-38 (RDFG) - F3-14 (GND) | Ignition switch ON, rear window defogger switch on | Below 1 V |
| F3-38 (RDFG) - F3-14 (GND) | Ignition switch ON, rear window defogger switch off | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Sedan
Disconnect the F60 and M1 back window glass connectors.
for Hatchback
Disconnect the Q3 and R6 back door glass connectors.
Remove the DEF relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F60-1 - DEF relay holder terminal 3 | Always | Below 1 Ω |
| M1-1 - Body ground | Always | Below 1 Ω |
| F60-1 - Body ground | Always | 10 kΩ or higher |
| DEF relay holder terminal 3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q3-1 - DEF relay holder terminal 3 | Always | Below 1 Ω |
| R6-1 - Body ground | Always | Below 1 Ω |
| Q3-1 - Body ground | Always | 10 kΩ or higher |
| DEF relay holder terminal 3 - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for Sedan) | A |
| OK (for Hatchback) | B |
| NG | C |
A
B
C