The driver side squib circuit consists of the airbag ECU assembly, spiral cable sub-assembly and horn button assembly.
The circuit instructs SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the driver side squib circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B1800/51 | Short in Driver Side Squib Circuit | ·
The airbag ECU assembly receives a line short circuit signal in the driver side squib circuit during primary check. ·
Driver side squib malfunction ·
Spiral cable sub-assembly malfunction ·
Airbag ECU assembly malfunction |
·
Instrument panel wire ·
Spiral cable sub-assembly ·
Horn button assembly (Driver side squib) ·
Airbag ECU assembly |
DTC corresponds to check mode. |
| B1801/51 | Open in Driver Side Squib Circuit | ·
The airbag ECU assembly receives an open circuit signal in the driver side squib circuit. ·
Driver side squib malfunction ·
Spiral cable sub-assembly malfunction ·
Airbag ECU assembly malfunction |
·
Instrument panel wire ·
Spiral cable sub-assembly ·
Horn button assembly (Driver side squib) ·
Airbag ECU assembly |
DTC corresponds to check mode. |
| B1802/51 | Short to GND in Driver Side Squib Circuit | ·
The airbag ECU assembly receives a short circuit to ground signal in the driver side squib circuit. ·
Driver side squib malfunction ·
Spiral cable sub-assembly malfunction ·
Airbag ECU assembly malfunction |
·
Instrument panel wire ·
Spiral cable sub-assembly ·
Horn button assembly (Driver side squib) ·
Airbag ECU assembly |
DTC corresponds to check mode. |
| B1803/51 | Short to B+ in Driver Side Squib Circuit | ·
The airbag ECU assembly receives a short circuit to B+ signal in the driver side squib circuit. ·
Driver side squib malfunction ·
Spiral cable sub-assembly malfunction ·
Airbag ECU assembly malfunction |
·
Instrument panel wire ·
Spiral cable sub-assembly ·
Horn button assembly (Driver side squib) ·
Airbag ECU assembly |
DTC corresponds to check mode. |
Perform the simulation method by selecting check mode (Signal Check) using the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *A | Airbag ECU 2 Connectors |
| *B | Airbag ECU 3 Connectors |
| *1 | Driver Side Squib |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag ECU Assembly |
| *4 | Instrument Panel Wire |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the horn button assembly, spiral cable sub-assembly and airbag ECU assembly.
The connectors are properly connected.
If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the horn button assembly, spiral cable sub-assembly and airbag ECU assembly.
Check that the terminals of the connectors are not damaged.
The terminals are not deformed or damaged.
Check that the spiral cable sub-assembly connector (on the steering pad side) is not damaged.
The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
Check that the short springs for the instrument panel wire and spiral cable sub-assembly with the activation prevention mechanism are not deformed or damaged.
The short springs are not deformed or damaged.
| Result | Proceed to |
|---|---|
| OK (Airbag ECU 2 Connectors) | A |
| OK (Airbag ECU 3 Connectors) | B |
| NG | C |
A
B
C
| *1 | Driver Side Squib |
| *2 | Spiral Cable Sub-Assembly |
| *3 | Airbag ECU Assembly |
| *a | Front view of wire harness connector
(to Horn Button Assembly (Driver Side Squib)) |
Connect the instrument panel wire to the airbag ECU assembly and spiral cable sub-assembly.
Connect SST (resistance 2.1 Ω) to connector E.
Never connect the tester to the horn button assembly (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.
Codes other than DTCs B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Driver Side Squib |
| *2 | Spiral Cable Sub-Assembly |
| *3 | Airbag ECU Assembly |
| *a | Front view of wire harness connector
(to Horn Button Assembly (Driver Side Squib)) |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Disconnect SST from connector E.
Disconnect the instrument panel wire from the airbag ECU assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| z3-2 - Body ground | Ignition switch ON | Below 1 V |
| z3-1 - Body ground | Ignition switch ON | Below 1 V |
Check for an open in the circuit.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z3-2 - z3-1 | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z3-2 - Body ground | Always | 1 MΩ or higher |
| z3-1 - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z3-2 - z3-1 | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Driver Side Squib |
| *2 | Spiral Cable Sub-Assembly |
| *3 | Airbag ECU Assembly |
Restore the released activation prevention mechanism of connector B to the original condition.
Connect the connectors to the horn button assembly and airbag ECU assembly.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.
Codes other than DTCs B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *1 | Driver Side Squib |
| *2 | Spiral Cable Sub-Assembly |
| *3 | Airbag ECU Assembly |
| *4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Spiral Cable Sub-Assembly (Driver Side Squib)) |
Restore the released activation prevention mechanism of connector B to the original condition.
Disconnect the instrument panel wire from the spiral cable sub-assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F9-1 (D+) - Body ground | Ignition switch ON | Below 1 V |
| F9-2 (D-) - Body ground | Ignition switch ON | Below 1 V |
Check for an open in the circuit.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F9-1 (D+) - F9-2 (D-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F9-1 (D+) - Body ground | Always | 1 MΩ or higher |
| F9-2 (D-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F9-1 (D+) - F9-2 (D-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Driver Side Squib |
| *2 | Spiral Cable Sub-Assembly |
| *3 | Airbag ECU Assembly |
| *4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Horn Button Assembly (Driver Side Squib)) |
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| z3-2 - Body ground | Ignition switch ON | Below 1 V |
| z3-1 - Body ground | Ignition switch ON | Below 1 V |
Check for an open in the circuit.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z3-2 - z3-1 | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z3-2 - Body ground | Always | 1 MΩ or higher |
| z3-1 - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector D.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z3-2 - z3-1 | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector D to the original condition.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *1 | Driver Side Squib |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag ECU Assembly |
| *a | Front view of wire harness connector
(to Steering Pad Switch Assembly) |
Connect the instrument panel wire to the airbag ECU assembly and spiral cable sub-assembly.
Connect SST (resistance 2.1 Ω) to connector E.
Never connect the tester to the steering pad switch assembly(driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.
Codes other than DTCs B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Driver Side Squib |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag ECU Assembly |
| *a | Front view of wire harness connector
(to Steering Pad Switch Assembly) |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Disconnect SST from connector E.
Disconnect the instrument panel wire from the airbag ECU assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| z3-2 - Body ground | Ignition switch ON | Below 1 V |
| z3-1 - Body ground | Ignition switch ON | Below 1 V |
Check for an open in the circuit.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z3-2 - z3-1 | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z3-2 - Body ground | Always | 1 MΩ or higher |
| z3-1 - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z3-2 - z3-1 | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Driver Side Squib |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag ECU Assembly |
Restore the released activation prevention mechanism of connector B to the original condition.
Connect the connectors to the steering pad switch assembly and airbag ECU assembly.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.
Codes other than DTCs B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *1 | Driver Side Squib |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag ECU Assembly |
| *4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Spiral Cable Sub-assembly) |
Restore the released activation prevention mechanism of connector B to the original condition.
Disconnect the instrument panel wire from the spiral cable sub-assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F9-1 (D+) - Body ground | Ignition switch ON | Below 1 V |
| F9-2 (D-) - Body ground | Ignition switch ON | Below 1 V |
Check for an open in the circuit.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F9-1 (D+) - F9-2 (D-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F9-1 (D+) - Body ground | Always | 1 MΩ or higher |
| F9-2 (D-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F9-1 (D+) - F9-2 (D-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Driver Side Squib |
| *2 | Spiral Cable Sub-assembly |
| *3 | Airbag ECU Assembly |
| *4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Steering Pad Switch Assembly) |
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| z3-2 - Body ground | Ignition switch ON | Below 1 V |
| z3-1 - Body ground | Ignition switch ON | Below 1 V |
Check for an open in the circuit.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z3-2 - z3-1 | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z3-2 - Body ground | Always | 1 MΩ or higher |
| z3-1 - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector D.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z3-2 - z3-1 | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector D to the original condition.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG