These DTCs are stored when the combination meter assembly detects an open in a turn signal light circuit, a short in a turn signal light circuit, or a short in the hazard warning light circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| B1507 | Open in Turn Signal Circuit | When IG voltage is 9.5 V or more and the following condition is detected:
·
Open in turn signal light circuit |
·
Bulb ·
Harness or connector ·
Driver side junction block assembly ·
Combination meter assembly |
DTC stored | - |
| B1508 | Short in Turn Signal / Hazard Flasher Circuit | When IG voltage is 9.5 V or more and the following condition is detected:
·
Short in turn signal light circuit or hazard warning light circuit |
·
Bulb ·
Harness or connector ·
Driver side junction block assembly ·
Combination meter assembly |
DTC stored | - |
Inspect the bulbs for this system before performing the following procedure.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Inspect the illumination of each turn signal light.
| Result | Proceed to |
|---|---|
| Turn signal lights for one side do not illuminate. | A |
| Front turn signal light does not illuminate. | B |
| Rear turn signal light does not illuminate (for Sedan). | C |
| Rear turn signal light does not illuminate (for Hatchback). | D |
| Side turn signal light does not illuminate (for Outer Rear View Mirror Type Side Turn Signal Light). | E |
| Side turn signal light does not illuminate (for Front Fender Type Side Turn Signal Light). | F |
A
B
C
D
E
F
Disconnect the F39 combination meter assembly connector.
Disconnect the 6N*1 or 6H*2 driver side junction block assembly connector.
*1: for LH
*2: for RH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F39-13 (LL) - 6N-7 | Always | Below 1 Ω |
| F39-13 (LL) or 6N-7 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F39-7 (LR) - 6H-8 | Always | Below 1 Ω |
| F39-7 (LR) or 6H-8 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A12*1 or A11*2 headlight assembly connector.
*1: for LH
*2: for RH
Disconnect the 6D*1 or 6E*2 driver side junction block assembly connector.
*1: for LH
*2: for RH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A12-2 (B) - 6D-8 | Always | Below 1 Ω |
| A12-2 (B) or 6D-8 - Body ground | Always | 10 kΩ or higher |
| A12-1 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A11-2 (B) - 6E-4 | Always | Below 1 Ω |
| A11-2 (B) or 6E-4 - Body ground | Always | 10 kΩ or higher |
| A11-1 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F25*1 or F26*2 rear combination light assembly connector.
*1: for LH
*2: for RH
Disconnect the 6N*1 or 6K*2 driver side junction block assembly connector.
*1: for LH
*2: for RH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F25-5 (B) - 6N-8 | Always | Below 1 Ω |
| F25-5 (B) or 6N-8 - Body ground | Always | 10 kΩ or higher |
| F25-4 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F26-5 (B) - 6K-6 | Always | Below 1 Ω |
| F26-5 (B) or 6K-6 - Body ground | Always | 10 kΩ or higher |
| F26-4 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F179*1 or F180*2 rear combination light assembly connector.
*1: for LH
*2: for RH
Disconnect the 6N*1 or 6K*2 driver side junction block assembly connector.
*1: for LH
*2: for RH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F179-4 (B) - 6N-8 | Always | Below 1 Ω |
| F179-4 (B) or 6N-8 - Body ground | Always | 10 kΩ or higher |
| F179-3 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F180-4 (B) - 6K-6 | Always | Below 1 Ω |
| F180-4 (B) or 6K-6 - Body ground | Always | 10 kΩ or higher |
| F180-3 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H6*1 or G6*2 outer rear view mirror assembly connector.
*1: for LH
*2: for RH
Disconnect the 6N*1 or 6K*2 driver side junction block assembly connector.
*1: for LH
*2: for RH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-10 (B) - 6N-10 | Always | Below 1 Ω |
| H6-10 (B) or 6N-10 - Body ground | Always | 10 kΩ or higher |
| H6-6 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G6-10 (B) - 6K-4 | Always | Below 1 Ω |
| G6-10 (B) or 6K-4 - Body ground | Always | 10 kΩ or higher |
| G6-6 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A15*1 or A16*2 side turn signal light assembly connector.
*1: for LH
*2: for RH
Disconnect the 6D*1 or 6C*2 driver side junction block assembly connector.
*1: for LH
*2: for RH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A15-1 (B) - 6D-10 | Always | Below 1 Ω |
| A15-1 (B) or 6D-10 - Body ground | Always | 10 kΩ or higher |
| A15-2 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A16-1 (B) - 6C-6 | Always | Below 1 Ω |
| A16-1 (B) or 6C-6 - Body ground | Always | 10 kΩ or higher |
| A16-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *a | Component without harness connected
(Driver Side Junction Block Assembly) |
- | - |
Front turn signal light
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6N-7 - 6D-8 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6H-8 - 6E-4 | Always | Below 1 Ω |
Rear turn signal light
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6N-7 - 6N-8 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6H-8 - 6K-6 | Always | Below 1 Ω |
Side turn signal light (for Outer Rear View Mirror Type Side Turn Signal Light)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6N-7 - 6N-10 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6H-8 - 6K-4 | Always | Below 1 Ω |
Side turn signal light (for Front Fender Type Side Turn Signal Light)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6N-7 - 6D-10 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6H-8 - 6C-6 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG