Home › Engine / Hybrid System › 1NR-FE ENGINE CONTROL › SFI SYSTEM › from 2018.01
RM30M0E _51 Engine / Hybrid System _053310 1NR-FE ENGINE CONTROL _0258661 SFI SYSTEM J

1NR-FE ENGINE CONTROL  SFI SYSTEM  Fuel Injector Circuit  


DESCRIPTION

They inject fuel into the cylinders based on signals from the ECM.

WIRING DIAGRAM

A300996E22
5.115,0.865 5.448,1.052 0.333,0.188 10 false B47 5.115,2.115 5.458,2.323 0.344,0.208 10 false B47 5.115,3.365 5.448,3.563 0.333,0.198 10 false B47 5.115,4.625 5.469,4.833 0.354,0.208 10 false B47 5.104,5.938 5.563,6.135 0.458,0.198 10 false B46 5.115,6.563 5.573,6.76 0.458,0.198 10 false B46 5.438,0.75 5.896,0.948 0.458,0.198 10 false #10 5.438,3.24 5.896,3.438 0.458,0.198 10 false #30 5.458,2.01 5.917,2.208 0.458,0.198 10 false #20 5.438,4.521 5.896,4.719 0.458,0.198 10 false #40 3.729,0.76 4.188,0.958 0.458,0.198 10 false 1 4.583,0.76 5.042,0.958 0.458,0.198 10 false 2 3.74,1.969 4.198,2.167 0.458,0.198 10 false 1 3.75,3.25 4.208,3.448 0.458,0.198 10 false 1 3.75,4.521 4.208,4.719 0.458,0.198 10 false 1 4.604,1.99 5.063,2.188 0.458,0.198 10 false 2 4.604,3.26 5.063,3.458 0.458,0.198 10 false 2 4.604,4.521 5.063,4.719 0.458,0.198 10 false 2 3.615,1.083 4.073,1.281 0.458,0.198 10 false B4 3.656,2.344 4.115,2.542 0.458,0.198 10 false B5 3.656,3.625 4.115,3.823 0.458,0.198 10 false B6 3.667,4.865 4.125,5.063 0.458,0.198 10 false B7 3.625,1.24 5.073,1.615 1.448,0.375 10 false Fuel Injector Assembly (No. 1 Cylinder) 5.198,0.656 5.375,0.854 0.177,0.198 10 false 4 5.177,1.938 5.323,2.115 0.146,0.177 10 false 3 5.177,3.156 5.354,3.354 0.177,0.198 10 false 2 5.198,4.427 5.365,4.646 0.167,0.219 10 false 1 5.188,5.75 5.646,5.948 0.458,0.198 10 false 1 5.198,6.375 5.656,6.573 0.458,0.198 10 false 2 5.99,7.25 6.448,7.448 0.458,0.198 10 false ECM 2.51,1.031 3.188,1.24 0.677,0.208 10 false IG2 NO. 1 0.573,1.281 2.115,1.667 1.542,0.385 10 false Ignition or Starter Switch Assembly*2 0.573,1.135 1.031,1.333 0.458,0.198 10 false F7 1.333,2.885 1.708,3.125 0.375,0.24 10 false IG2*1 1.854,2.406 2.313,2.604 0.458,0.198 10 false 1 1.865,1.99 2.323,2.188 0.458,0.198 10 false 5 1,2.385 1.458,2.583 0.458,0.198 10 false 2 0.99,2.01 1.448,2.208 0.458,0.198 10 false 3 0.604,0.75 1.063,0.948 0.458,0.198 10 false 5 1.969,0.76 2.427,0.958 0.458,0.198 10 false 6 1.667,0.771 2.344,0.979 0.677,0.208 10 false IG2 0.76,0.76 1.438,0.969 0.677,0.208 10 false AM2 0.354,4.75 1.031,4.958 0.677,0.208 10 false AM2 0.365,5.365 1.042,5.573 0.677,0.208 10 false MAIN 0.531,6.635 1.208,6.844 0.677,0.208 10 false Battery 1.49,4.115 2.167,4.323 0.677,0.208 10 false IG1D 1.25,3.979 1.708,4.177 0.458,0.198 10 false 20 1.188,4.76 1.646,4.958 0.458,0.198 10 false F43 1.198,4.948 3.031,5.458 1.833,0.51 10 false Certification ECU (Smart Key ECU Assembly)*1 1.167,6.417 6.521,6.615 5.354,0.198 10 false *1: w/ Smart Entry and Start System 1.177,6.917 6.531,7.115 5.354,0.198 10 false *2: w/o Smart Entry and Start System 2.042,2.781 2.5,2.979 0.458,0.198 10 false *1 0.74,3.177 1.198,3.375 0.458,0.198 10 false *1 2.302,1.573 2.76,1.771 0.458,0.198 10 false *1 0.625,2.021 1.083,2.219 0.458,0.198 10 false *1 0.115,1.385 0.573,1.583 0.458,0.198 10 false *2 2.104,0.76 2.563,0.958 0.458,0.198 10 false *2 5.427,5.833 5.885,6.031 0.458,0.198 10 false E01 5.438,6.469 5.896,6.667 0.458,0.198 10 false E02 3.656,2.5 5.094,2.885 1.438,0.385 10 false Fuel Injector Assembly (No. 2 Cylinder) 3.656,3.771 5.104,4.188 1.448,0.417 10 false Fuel Injector Assembly (No. 3 Cylinder) 3.677,5 5.115,5.396 1.438,0.396 10 false Fuel Injector Assembly (No. 4 Cylinder) 0.365,6 1.042,6.208 0.677,0.208 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
A226264C21
0.396,0.448 0.771,0.708 0.375,0.26 0.396,0.833 0.771,1.094 0.375,0.26 0.406,1.208 0.781,1.469 0.375,0.26 0.417,1.573 0.792,1.833 0.375,0.26 0.073,0.115 0.25,0.271 0.177,0.156 10 false *a 0.521,0.49 0.844,0.75 0.323,0.26 10 false B4 0.51,0.885 0.823,1.135 0.313,0.25 10 false B5 0.51,1.26 0.833,1.542 0.323,0.281 10 false B6 0.51,1.625 0.875,1.906 0.365,0.281 10 false B7
*a Front view of wire harness connector
(to Fuel Injector Assembly)


a.

Disconnect the fuel injector assembly connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B4-1 - Body ground Ignition switch ON 11 to 14 V
B5-1 - Body ground Ignition switch ON 11 to 14 V
B6-1 - Body ground Ignition switch ON 11 to 14 V
B7-1 - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK A
NG (w/ Smart Entry and Start System) B
NG (w/o Smart Entry and Start System) C



A

2.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)

B

5.CHECK HARNESS AND CONNECTOR (IG2 RELAY - FUEL INJECTOR ASSEMBLY)

C

6.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - IGNITION OR STARTER SWITCH ASSEMBLY)
2.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
a.

Inspect the fuel injector assembly.

Click hereEngine / Hybrid System>1NR-FE FUEL>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - FUEL INJECTOR ASSEMBLY)

NG

REPLACE FUEL INJECTOR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - FUEL INJECTOR ASSEMBLY)
a.

Disconnect the B4, B5, B6 and B7 fuel injector assembly connectors.


b.

Disconnect the B47 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B47-4 (#10) - B4-2 Always Below 1 Ω
B47-3 (#20) - B5-2 Always Below 1 Ω
B47-2 (#30) - B6-2 Always Below 1 Ω
B47-1 (#40) - B7-2 Always Below 1 Ω
B47-4 (#10) or B4-2 - Body ground and other terminals Always 10 kΩ or higher
B47-3 (#20) or B5-2 - Body ground and other terminals Always 10 kΩ or higher
B47-2 (#30) or B6-2 - Body ground and other terminals Always 10 kΩ or higher
B47-1 (#40) or B7-2 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the B46 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B46-1 (E01) - Body ground Always Below 1 Ω
B46-2 (E02) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (IG2 RELAY - FUEL INJECTOR ASSEMBLY)
a.

Remove the IG2 relay from the No. 4 relay block.


b.

Disconnect the B4, B5, B6 and B7 fuel injector assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
5 (IG2 relay holder) - B4-1 Always Below 1 Ω
5 (IG2 relay holder) - B5-1 Always Below 1 Ω
5 (IG2 relay holder) - B6-1 Always Below 1 Ω
5 (IG2 relay holder) - B7-1 Always Below 1 Ω
5 (IG2 relay holder) or B4-1 - Body ground and other terminals Always 10 kΩ or higher
5 (IG2 relay holder) or B5-1 - Body ground and other terminals Always 10 kΩ or higher
5 (IG2 relay holder) or B6-1 - Body ground and other terminals Always 10 kΩ or higher
5 (IG2 relay holder) or B7-1 - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - IGNITION OR STARTER SWITCH ASSEMBLY)
a.

Disconnect the B4, B5, B6 and B7 fuel injector assembly connectors.


b.

Disconnect F7 ignition or starter switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
B4-1 - F7-6 (IG2) Always Below 1 Ω
B5-1 - F7-6 (IG2) Always Below 1 Ω
B6-1 - F7-6 (IG2) Always Below 1 Ω
B7-1 - F7-6 (IG2) Always Below 1 Ω
B4-1 or F7-6 (IG2) - Body ground and other terminals Always 10 kΩ or higher
B5-1 or F7-6 (IG2) - Body ground and other terminals Always 10 kΩ or higher
B6-1 or F7-6 (IG2) - Body ground and other terminals Always 10 kΩ or higher
B7-1 or F7-6 (IG2) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR