Home › Engine / Hybrid System › 2NR-FE ENGINE CONTROL › SFI SYSTEM › from 2018.01
RM30M0E _51 Engine / Hybrid System _053304 2NR-FE ENGINE CONTROL _0258353 SFI SYSTEM C

2NR-FE ENGINE CONTROL  SFI SYSTEM  C1263  Ejector VSV Malfunction (High)  C1264  Ejector VSV Malfunction (Low)  


DESCRIPTION

The brake ejector VSV is installed on the throttle by-pass and controlled by the ECM to optimally apply vacuum to the brake booster assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
C1263 Ejector VSV Malfunction (High)

Both of the following conditions are met for 3 seconds or more (1 trip detection logic):

1.

Ignition switch is ON.

2.

Short to +B in brake ejector VSV circuit when VSV operation command is on.



·

Short to +B in brake ejector VSV circuit

·

Brake ejector VSV

·

ECM


Does not come on DTC stored
C1264 Ejector VSV Malfunction (Low)

Both of the following conditions are met for 3 seconds or more (1 trip detection logic):

1.

Ignition switch is ON.

2.

Open or short to ground in brake ejector VSV circuit when VSV operation command is off.



·

Open or short in brake ejector VSV circuit

·

Brake ejector VSV

·

ECM


Does not come on DTC stored

MONITOR DESCRIPTION

The ECM monitors the terminal voltage input from the brake ejector VSV. If the voltage and brake ejector VSV operation command signal do not match, the ECM judges that there is a malfunction in the brake ejector VSV circuit and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components Brake ejector VSV
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A179391E73
0.948,1.583 1.365,1.167 false 5.094,3.031 5.875,3.292 0.781,0.26 10 false [E] 3.875,3.031 4.333,3.24 0.458,0.208 10 false [C] 1.302,2.583 2.219,2.938 0.917,0.354 10 false Warming up 0.531,2.104 1.156,2.458 0.625,0.354 10 false Idling 2.646,2.583 3.375,2.979 0.729,0.396 10 false 15 minutes or more 4.219,2.583 4.948,2.979 0.729,0.396 10 false 10 minutes or more 1.552,1.979 1.781,2.198 0.229,0.219 10 false [A] 2.844,1.979 3.094,2.208 0.25,0.229 10 false [B] 4.552,1.365 4.771,1.573 0.219,0.208 10 false [D] 0.083,0.5 1.073,0.74 0.99,0.24 10 false Vehicle Speed 1.417,1.073 5.542,1.271 4.125,0.198 10 false Between 40 km/h and 60 km/h (25 and 37 mph)

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

HINT:

The A/C (if equipped) switch and all accessory switches should be off.


9.

Idle the engine for 15 minutes or more [B].

10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: C1263 or C1264.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].



15.

Drive the vehicle at a constant speed between 40 and 60 km/h (25 and 37 mph) for 10 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


16.

Check the DTC judgment result again [E].


WIRING DIAGRAM

A361815E51
0.938,0.917 1.094,1.115 0.156,0.198 10 false 1 0.969,1.427 1.125,1.625 0.156,0.198 10 false 8 0.927,1.115 1.25,1.365 0.323,0.25 10 false 6B 0.927,1.646 1.25,1.896 0.323,0.25 10 false 6J 1.375,1.281 2.115,1.448 0.74,0.167 10 false EFI-MAIN 2.354,1.917 2.771,2.083 0.417,0.167 10 false EFI 2.906,1.26 3.646,1.427 0.74,0.167 10 false EFI NO. 2 3.677,1.125 4,1.375 0.323,0.25 10 false 6H 3.708,0.896 3.865,1.094 0.156,0.198 10 false 3 3.708,1.833 3.865,2.031 0.156,0.198 10 false 9 3.698,2.063 4.021,2.313 0.323,0.25 10 false 6L 4.208,1.01 4.365,1.208 0.156,0.198 10 false 1 5.292,1.01 5.448,1.208 0.156,0.198 10 false 2 5.604,1.125 6.01,1.375 0.406,0.25 10 false B47 5.646,0.917 5.979,1.083 0.333,0.167 10 false 14 5.667,1.854 6,2.021 0.333,0.167 10 false 6 5.583,2.063 5.99,2.313 0.406,0.25 10 false F130 4.188,1.438 4.594,1.688 0.406,0.25 10 false B52 4.188,1.594 5.51,1.844 1.323,0.25 10 false Brake Ejector VSV 1.344,2.406 3.75,2.656 2.406,0.25 10 false Driver Side Junction Block Assembly 0.406,2.667 1.146,2.833 0.74,0.167 10 false MAIN 0.417,3.25 1.156,3.417 0.74,0.167 10 false FL MAIN 0.594,3.896 1.333,4.063 0.74,0.167 10 false Battery 5.969,0.979 6.375,1.146 0.406,0.167 10 false PBV 6.01,2.063 6.5,2.229 0.49,0.167 10 false MREL 6.25,3.167 6.74,3.333 0.49,0.167 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (BRAKE EJECTOR VSV INSPECTION)
A356990C03
1.573,1.073 2.344,1.417 true 0.813,1.604 0.354,1.5 true 2.396,1.354 2.708,1.552 0.313,0.198 10 false *1 0.188,1.396 0.51,1.594 0.323,0.198 10 false *2
*1 Brake ejector VSV
*2 Vacuum hose (Air cleaner side)


a.

Disconnect the vacuum hose (Air cleaner side) of the brake ejector VSV.


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Brake Ejector VSV Inspection.

Powertrain > Engine and ECT > Active Test
Tester Display
Brake Ejector VSV Inspection
50004 234 249

f.

When the brake ejector VSV is operated using the GTS, check whether the port of the brake ejector VSV applies suction your finger.

OK:
GTS Operation Specified Condition
ON Brake ejector VSV port applies suction to finger
OFF Brake ejector VSV port applies no suction to finger



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT BRAKE EJECTOR VSV
2.INSPECT BRAKE EJECTOR VSV
a.

Inspect the brake ejector VSV.

Click hereBrake>BRAKE SYSTEM (OTHER)>VACUUM SWITCHING VALVE>INSPECTION

Result:
Proceed to
OK
NG




OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF BRAKE EJECTOR VSV)

NG

REPLACE BRAKE EJECTOR VSV

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF BRAKE EJECTOR VSV)
A225830C71
0.469,1.188 0.969,1.438 0.5,0.25 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 0.594,1.229 0.906,1.385 0.313,0.156 10 false B52
*a Front view of wire harness connector
(to Brake Ejector VSV)


a.

Disconnect the brake ejector VSV connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B52-1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BRAKE EJECTOR VSV - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (BRAKE EJECTOR VSV - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (BRAKE EJECTOR VSV - ECM)
a.

Disconnect the B52 brake ejector VSV connector.


b.

Disconnect the B47 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B47-14 (PBV) - B52-2 Always Below 1 Ω
B47-14 (PBV) or B52-2 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BRAKE EJECTOR VSV - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the B52 brake ejector VSV connector.


b.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B52-1 - 6H-3 Always Below 1 Ω
B52-1 or 6H-3 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR