Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2018.01
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090853 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Theft Deterrent System is not Unset when Engine is Running  


DESCRIPTION

The theft deterrent system is unset when the IG signal and engine speed signal are input to the body computer for 2 seconds or more continuously.

The engine speed signal is sent from the ECM to the body computer. For this reason, if there is an abnormality in an ECU or wire harness, the system may not function correctly.

WIRING DIAGRAM

E383630E03
0.417,0.302 4.542,0.5 4.125,0.198 10 false from Door Control Battery*1 0.26,1.5 2.094,2.094 1.833,0.594 10 false from Ignition or Starter Switch Assembly*3 or IG1 Relay*4 2.844,1.01 4.125,1.552 1.281,0.542 10 false D/L NO. 1 4.49,1.635 5.771,2.177 1.281,0.542 10 false ECU-IG NO. 1 2.833,4 4.115,4.542 1.281,0.542 10 false F131 2.823,4.135 4.104,4.677 1.281,0.542 10 false ECM 0.042,4.344 2.396,4.823 2.354,0.479 10 false *3: w/o Smart Entry and Start System 0.052,4.667 2.469,5.167 2.417,0.5 10 false *4: w/ Smart Entry and Start System 0.042,3.708 2.406,4.188 2.365,0.479 10 false *1: w/ Door Control Battery 3.917,0.667 4.073,0.865 0.156,0.198 10 false 1 3.906,1.302 4.063,1.5 0.156,0.198 10 false 1 3.927,1.875 4.083,2.073 0.156,0.198 10 false 8 5.708,0.667 5.875,0.865 0.167,0.198 10 false 6 5.708,1.26 5.875,1.458 0.167,0.198 10 false 7 5.677,1.885 5.833,2.083 0.156,0.198 10 false 1 5.677,3.344 6.01,3.625 0.333,0.281 10 false 13 3.521,3.427 3.927,3.76 0.406,0.333 10 false 16 3.542,4.802 3.698,5 0.156,0.198 10 false 6 4.719,4.271 4.969,4.469 0.25,0.198 10 false *4 3.875,0.885 4.125,1.083 0.25,0.198 10 false 6O 3.885,1.5 4.135,1.698 0.25,0.198 10 false 6F 3.885,2.094 4.135,2.292 0.25,0.198 10 false 6J 5.646,0.875 5.896,1.073 0.25,0.198 10 false MB 5.635,1.51 5.885,1.708 0.25,0.198 10 false MB 5.625,2.094 5.875,2.292 0.25,0.198 10 false MB 5.635,3.552 5.885,3.75 0.25,0.198 10 false F52 6,0.865 6.667,1.115 0.667,0.25 10 false BECU 6,1.49 6.667,1.74 0.667,0.25 10 false IG 6,2.073 6.667,2.323 0.667,0.25 10 false GND 5.99,3.573 6.656,3.823 0.667,0.25 10 false TACH 2.417,5.563 4.281,6.063 1.865,0.5 10 false Certification ECU (Smart Key ECU Assembly)*4 2.417,5.385 3.698,5.927 1.281,0.542 10 false F43 3.25,4.948 4.531,5.49 1.281,0.542 10 false NE 3.156,3.542 4.438,4.083 1.281,0.542 10 false NEO 5.927,5.729 6.927,6.146 1,0.417 10 false Body Computer 1.198,0.885 5.323,1.083 4.125,0.198 10 false from Battery*2 0.042,4.021 2.406,4.5 2.365,0.479 10 false *2: w/o Door Control Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE(+B))
a.

Disconnect the driver side junction block assembly connectors.


b.
E383631C03
1.333,0.5 1.833,0.75 0.5,0.25 0.083,0.083 0.417,0.281 0.333,0.198 10 false *a 1.49,0.552 1.802,0.75 0.313,0.198 10 false 6O
*a Front view of wire harness connector
(to Driver Side Junction Block Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
6O-1 - Body ground Always 11 to 14 V



Result:
Result Proceed to
OK A
NG (w/ Door Control Battery) B
NG (w/o Door Control Battery) C



A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE(IG))

B

GO TO POWER DOOR LOCK CONTROL SYSTEM (POWER SOURCE CIRCUIT)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE(IG))
a.

Disconnect the driver side junction block assembly connectors.


b.
E277232C05
1.417,0.5 1.833,0.75 0.417,0.25 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 1.552,0.531 1.885,0.729 0.333,0.198 10 false 6F
*a Front view of wire harness connector
(to Driver Side Junction Block Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
6F-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

b.

Disconnect the driver side junction block assembly connectors.


c.

Measure the resistance according the value(s) in the table below.

E379196C02
1.792,0.583 2.198,0.75 0.406,0.167 4.479,0.5 4.833,0.667 0.354,0.167 5.813,0.417 6.146,0.594 0.333,0.177 2.281,1.094 1.875,1.5 true 2.75,1.469 2.406,1.125 true 1.885,0.583 2.198,0.781 0.313,0.198 10 false MB 4.583,0.51 4.896,0.708 0.313,0.198 10 false 6O 5.917,0.427 6.229,0.625 0.313,0.198 10 false 6F 2.823,1.448 3.438,1.646 0.615,0.198 10 false BECU 1.677,1.448 2.292,1.646 0.615,0.198 10 false IG 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a
*a Component without harness connected
(Driver Side Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
6O-1 - MB-6 (BECU) Always Below 1 Ω
6F-1 - MB-7 (IG) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK BODY COMPUTER (ENGINE SPEED SIGNAL INPUT)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

4.CHECK BODY COMPUTER (ENGINE SPEED SIGNAL INPUT)
a.

Install the body computer to the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


b.

Reconnect the body computer connector.


c.

Reconnect the 6O, 6F and 6J driver side junction block assembly connectors.


d.

Remove the driver side junction block assembly with connectors still connected.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


e.
E277231C02
1.417,0.25 1.833,0.5 0.417,0.25 2.146,1.375 2.469,1.875 true 0.052,0.052 0.365,0.208 0.313,0.156 10 false *a 2.521,1.781 3.073,1.979 0.552,0.198 10 false TACH 1.51,0.281 1.969,0.479 0.458,0.198 10 false F52
*a Component with harness connected
(Body Computer)


Check the engine speed input signal waveform at the terminal of body computer.

Standard Frequency:
Tester Connection Condition Specified Condition
F52-13 (TACH) - Body ground Engine stopped No pulse generation
F52-13 (TACH) - Body ground Engine running Pulse generation



Result:
Result Proceed to
OK A
NG (w/ Smart Entry and Start System) B
NG (w/o Smart Entry and Start System) C



A

B

5.CHECK HARNESS AND CONNECTOR (BODY COMPUTER - ECM AND CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

C

10.CHECK HARNESS AND CONNECTOR (BODY COMPUTER - ECM)
5.CHECK HARNESS AND CONNECTOR (BODY COMPUTER - ECM AND CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the F52 body computer connector.


b.

Disconnect the F131 ECM connector.


c.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F52-13 (TACH) - F131-16 (NEO) Always Below 1 Ω
F52-13 (TACH) - F43-6 (NE) Always Below 1 Ω
F131-16 (NEO) - F43-6 (NE) Always Below 1 Ω
F52-13 (TACH) or F131-16 (NEO) - Body ground Always 10 kΩ or higher
F52-13 (TACH) or F43-6 (NE) - Body ground Always 10 kΩ or higher
F131-16 (NEO) or F43-6 (NE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK ECM (ENGINE SPEED SIGNAL OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK ECM (ENGINE SPEED SIGNAL OUTPUT)
a.

Disconnect the F52 body computer connector.


b.

Reconnect the F131 ECM connector.


c.

Reconnect the F43 certification ECU (smart key ECU assembly) connector.


d.
E348832C01
2.094,0.396 2.552,0.656 0.458,0.26 2.198,0.958 2.729,1.771 true 2.167,0.448 2.781,0.646 0.615,0.198 10 false F131 2.656,1.813 3.115,2.01 0.458,0.198 10 false NEO 0.146,0.167 0.458,0.365 0.313,0.198 10 false *a
*a Component with harness connected
(ECM)


Check the engine speed input signal waveform at the terminal of ECM.

Standard Frequency:
Tester Connection Condition Specified Condition
F131-16 (NEO) - Body ground Engine stopped No pulse generation
F131-16 (NEO) - Body ground Engine running Pulse generation



Result:
Result Proceed to
NG A
OK B



A

7.CHECK ECM (VOLTAGE)

B

7.CHECK ECM (VOLTAGE)
a.

Disconnect the F52 body computer connector.


b.

Disconnect the F131 ECM connector.


c.
E347661C01
1.417,0.167 1.917,0.417 0.5,0.25 2.521,1.573 2.198,1.229 true 0.188,0.167 0.5,0.365 0.313,0.198 10 false *a 1.5,0.219 1.917,0.417 0.417,0.198 10 false F131 2.531,1.594 2.948,1.792 0.417,0.198 10 false NEO
*a Front view of wire harness connector
(to ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F131-16 (NEO) - Body ground Engine stopped 11 to 14 V



Result:
Result Proceed to
OK A
NG (for 1NR-FE) B
NG (for 2NR-FE) C



A

8.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

C

8.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.CHECK ECM (ENGINE SPEED SIGNAL OUTPUT)
9.CHECK ECM (ENGINE SPEED SIGNAL OUTPUT)
a.

Disconnect the F52 body computer connector.


b.

Reconnect the F131 ECM connector.


c.

Reconnect the F43 certification ECU (smart key ECU assembly) connector.


d.
E348832C01
2.094,0.396 2.552,0.656 0.458,0.26 2.198,0.958 2.729,1.771 true 2.167,0.448 2.781,0.646 0.615,0.198 10 false F131 2.656,1.813 3.115,2.01 0.458,0.198 10 false NEO 0.146,0.167 0.458,0.365 0.313,0.198 10 false *a
*a Component with harness connected
(ECM)


Check the engine speed input signal waveform at the terminal of ECM.

Standard Frequency:
Tester Connection Condition Specified Condition
F131-16 (NEO) - Body ground Engine stopped No pulse generation
F131-16 (NEO) - Body ground Engine running Pulse generation



Result:
Result Proceed to
OK A
NG (for 1NR-FE) B
NG (for 2NR-FE) C



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

C

10.CHECK HARNESS AND CONNECTOR (BODY COMPUTER - ECM)
a.

Disconnect the F52 body computer connector.


b.

Disconnect the F131 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F52-13 (TACH) - F131-16 (NEO) Always Below 1 Ω
F52-13 (TACH) or F131-16 (NEO) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for 1NR-FE) A
OK (for 2NR-FE) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR