Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › from 2018.01
RM30M0E _58 Vehicle Interior _017117 SEAT BELT _0084737 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Front Passenger Side Seat Belt Warning Light Malfunction  


DESCRIPTION

HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


The separate type front seat cushion pad (occupant detection sensor) detects if the passenger seat is occupied and sends signals to the combination meter assembly. The front seat inner belt assembly (passenger side) detects the passenger seat belt condition and sends signals to the combination meter assembly. After receiving the signals from the separate type front seat cushion pad (occupant detection sensor) and front seat inner belt assembly (passenger side), the seat belt warning light on the combination meter assembly will blink or go off.

WIRING DIAGRAM

C294867E09
1.219,0.771 1.635,0.979 0.417,0.208 10 false P/SB 1.635,0.667 1.948,0.865 0.313,0.198 10 false 6 2.521,0.76 2.927,0.948 0.406,0.188 10 false F121 5.583,0.75 5.99,0.938 0.406,0.188 10 false F121 2.781,1.135 3.188,1.323 0.406,0.188 10 false 1 3.052,1.135 3.458,1.323 0.406,0.188 10 false B 4.042,1.125 4.448,1.313 0.406,0.188 10 false B 4.333,1.156 5.625,1.75 1.292,0.594 10 false Front Seat Inner Belt Assembly RH 3.75,1.125 4.156,1.313 0.406,0.188 10 false 3 2.542,1.896 4.969,2.635 2.427,0.74 10 false Occupant Detection Sensor (Separate Type Front Seat Cushion Pad RH) 0.563,1.844 0.948,2.052 0.385,0.208 10 false F38 0.552,2.01 1.76,2.385 1.208,0.375 10 false Combination Meter Assembly 2.646,0.563 3.052,0.75 0.406,0.188 10 false 3 5.688,0.563 6.094,0.75 0.406,0.188 10 false 2 2.948,0.646 3.354,0.833 0.406,0.188 10 false + 5.365,0.656 5.771,0.844 0.406,0.188 10 false E 0.125,0.073 1,0.51 0.875,0.438 12 false for LHD:

C294867E10
1.208,0.771 1.656,1.01 0.448,0.24 10 false P/SB 1.635,0.667 1.948,0.865 0.313,0.198 10 false 6 2.563,0.76 2.969,0.948 0.406,0.188 10 false F29 5.615,0.75 6.021,0.938 0.406,0.188 10 false F29 2.781,1.135 3.188,1.323 0.406,0.188 10 false 1 3.052,1.135 3.458,1.323 0.406,0.188 10 false B 4.042,1.125 4.448,1.313 0.406,0.188 10 false B 4.323,1.167 5.74,1.74 1.417,0.573 10 false Front Seat Inner Belt Assembly LH 3.75,1.125 4.156,1.313 0.406,0.188 10 false 3 2.542,1.896 4.969,2.635 2.427,0.74 10 false Occupant Detection Sensor (Separate Type Front Seat Cushion Pad LH) 0.563,1.844 0.948,2.052 0.385,0.208 10 false F38 0.552,2.01 1.76,2.385 1.208,0.375 10 false Combination Meter Assembly 2.646,0.563 3.052,0.75 0.406,0.188 10 false 3 5.688,0.563 6.094,0.75 0.406,0.188 10 false 2 2.948,0.646 3.354,0.833 0.406,0.188 10 false + 5.365,0.656 5.771,0.844 0.406,0.188 10 false E 0.146,0.083 1.49,0.375 1.344,0.292 12 false for RHD:

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (DRIVER SIDE SEAT BELT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Driver Side Seat Belt Front seat belt warning light OFF or ON Confirm that the vehicle is stopped with the engine idling
Body Electrical > Combination Meter > Active Test
Tester Display
Driver Side Seat Belt
50004 122 12

OK:

Front seat belt warning light condition can be switched by Active Test.


Result:
Result
OK
NG



OK

2.READ VALUE USING GTS (P-SEATBELT BUCKLE SW)

NG

REPLACE COMBINATION METER ASSEMBLY

2.READ VALUE USING GTS (P-SEATBELT BUCKLE SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P-Seatbelt Buckle SW Front passenger seat belt buckle switch signal ON or OFF OFF: Front passenger seat belt not fastened
ON: Front passenger seat belt fastened
The front passenger seat is occupied
Body Electrical > Combination Meter > Data List
Tester Display
P-Seatbelt Buckle SW
50003 122 7

OK:

The GTS display changes correctly in response to the front passenger seat belt condition.


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

3.INSPECT OCCUPANT DETECTION SENSOR
3.INSPECT OCCUPANT DETECTION SENSOR
a.

Remove the occupant detection sensor.

Click hereVehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>REMOVAL


b.

Inspect the occupant detection sensor.

Click hereVehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>INSPECTION


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

4.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH

B

6.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH

C

REPLACE OCCUPANT DETECTION SENSOR

4.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH
a.
B332790C32
1.5,0.25 1.938,0.5 0.438,0.25 1.5,2.583 2,2.833 0.5,0.25 1.646,1.594 0.927,2.469 true 2.052,1.594 2.677,2.448 true 0.135,0.073 0.448,0.229 0.313,0.156 10 false *a 0.865,2.5 1.021,2.698 0.156,0.198 10 false + 2.667,2.479 2.823,2.677 0.156,0.198 10 false E 1.573,0.302 1.969,0.542 0.396,0.24 10 false F121 1.688,2.625 2.083,2.865 0.396,0.24 10 false B
*a Component without harness connected
(Front Seat Inner Belt Assembly (front passenger side))


Remove the front seat inner belt assembly RH.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F121-3 (+) - B-1 Always Below 1 Ω
F121-2 (E) - B-3 Front passenger seat belt unfastened Below 1 Ω
F121-2 (E) - B-3 Front passenger seat belt fastened 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FRONT SEAT INNER BELT ASSEMBLY RH - BODY GROUND)

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FRONT SEAT INNER BELT ASSEMBLY RH - BODY GROUND)
a.

Disconnect the F38 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-6 (P/SB) - F121-3 (+) Always Below 1 Ω
F38-6 (P/SB) or F121-3 (+) - Body ground Always 10 kΩ or higher
F121-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH
a.
B332790C33
1.5,0.25 1.938,0.5 0.438,0.25 1.5,2.583 2,2.833 0.5,0.25 1.646,1.594 0.927,2.469 true 2.052,1.594 2.677,2.448 true 0.135,0.073 0.448,0.229 0.313,0.156 10 false *a 0.865,2.5 1.021,2.698 0.156,0.198 10 false + 2.667,2.479 2.823,2.677 0.156,0.198 10 false E 1.594,0.302 1.99,0.542 0.396,0.24 10 false F29 1.688,2.625 2.083,2.865 0.396,0.24 10 false B
*a Component without harness connected
(Front Seat Inner Belt Assembly (front passenger side))


Remove the front seat inner belt assembly LH.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-3 (+) - B-1 Always Below 1 Ω
F29-2 (E) - B-3 Front passenger seat belt unfastened Below 1 Ω
F29-2 (E) - B-3 Front passenger seat belt fastened 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FRONT SEAT INNER BELT ASSEMBLY LH - BODY GROUND)

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FRONT SEAT INNER BELT ASSEMBLY LH - BODY GROUND)
a.

Disconnect the F38 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-6 (P/SB) - F29-3 (+) Always Below 1 Ω
F38-6 (P/SB) or F29-3 (+) - Body ground Always 10 kΩ or higher
F29-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR