Refer to DTC P013001.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>P013001
When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor (sensor 1) heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.
Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor (sensor 1).
The ECM has a pulse width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor (sensor 1) heater circuit uses a relay on the +B side of the circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P003012 | HO2S Heater Control Bank 1 Sensor 1 Circuit Short to Battery | The air fuel ratio sensor (sensor 1) heater current is more than the specified value while the heater is operating (1 trip detection logic). | ·
Short in air fuel ratio sensor (sensor 1) heater circuit ·
Air fuel ratio sensor (sensor 1) ·
ECM |
Comes on | DTC stored | SAE: P0032 |
| P003013 | HO2S Heater Control Bank 1 Sensor 1 Circuit Open | The air fuel ratio sensor (sensor 1) heater current is less than the specified value while the heater is operating (1 trip detection logic). | ·
Open or short in air fuel ratio sensor (sensor 1) heater circuit ·
Air fuel ratio sensor (sensor 1) ·
A/F HTR relay ·
ECM |
Comes on | DTC stored | SAE: P0031 |
| P101A9E | A/F Sensor Heater Performance Bank 1 Sensor 1 Stuck On | The air fuel ratio sensor (sensor 1) heater voltage level is low while the heater is not operating (1 trip detection logic). | ·
Short in air fuel ratio sensor (sensor 1) heater circuit ·
Air fuel ratio sensor (sensor 1) ·
ECM |
Comes on | DTC stored | SAE: P101D |
The ECM uses information from the air fuel ratio sensor (sensor 1) to regulate the air fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the three-way catalytic converter to purify the exhaust gases.
The air fuel ratio sensor (sensor 1) detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum-coated zirconia and includes an integrated heating element.
The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.
The air fuel ratio sensor (sensor 1) is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful current signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor (sensor 1) becomes inaccurate. As a result, the ECM is unable to regulate the air fuel ratio properly.
When the current in the air fuel ratio sensor (sensor 1) heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.
| Frequency of Operation | Continuous |
| Output duty cycle | 10% or higher |
| Output duty cycle | 30% or higher |
| Output duty cycle | Less than 75% |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON [A].
Turn the GTS on.
Start the engine and idle it for 5 minutes or more [B].
With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].
Idle the engine for 5 minutes or more [D].
Enter the following menus: Powertrain / Engine / Trouble Codes [E].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P003012, P003013 or P101A9E.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system has a malfunction.
If the judgment result is INCOMPLETE, perform steps [B] through [E] again.
Inspect the fuses for circuits related to this system before performing the following procedure.
Refer to "Data List / Active Test" [A/F (O2) Sensor Heater Duty Ratio B1S1].
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the air fuel ratio sensor (sensor 1) output current (Click here Engine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>P013616). If the sensor output current does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR (for Sensor 1)>INSPECTION
Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR (for Sensor 1)>REMOVAL
Pre-procedure1
Disconnect the air fuel ratio sensor (sensor 1) connector.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D40-5 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
Post-procedure1
None.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the air fuel ratio sensor (sensor 1) connector.
Disconnect the ECM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D40-4 (HA1A) - D51-9 (HA1A) | Always | Below 1 Ω |
| D40-4 (HA1A) or D51-9 (HA1A) - Body ground and other terminals | Always | 10 kΩ or higher |
Post-procedure1
None.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
None.
Procedure1
Clear the DTCs.
Post-procedure1
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Procedure1
Read the DTCs.
Post-procedure1
None.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| P003012, P003013 or P101A9E is output | B |
A
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
B
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>RELAY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | A/F HTR Relay |
Pre-procedure1
Remove the A/F HTR relay from the No. 1 engine room relay block and junction block assembly.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (A/F HTR relay) - Body ground | Always | 11 to 14 V |
Post-procedure1
None.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Remove the A/F HTR relay from the No. 1 engine room relay block and junction block assembly.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (A/F HTR relay) - Body ground | Always | Below 1 Ω |
Post-procedure1
None.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Remove the A/F HTR relay from the No. 1 engine room relay block and junction block assembly.
Disconnect the air fuel ratio sensor (sensor 1) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (A/F HTR relay) - D40-5 (+B) | Always | Below 1 Ω |
| 5 (A/F HTR relay) or D40-5 (+B) - Body ground and other terminals | Always | 10 kΩ or higher |
Post-procedure1
None.
| Proceed to |
|---|
| OK |
| NG |
OK
NG