Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › SFI SYSTEM › 2020.03–2020.07
RM36W0E _51 Engine / Hybrid System _087499 M15A-FKS ENGINE CONTROL _0418534 SFI SYSTEM C

M15A-FKS ENGINE CONTROL  SFI SYSTEM  P042000  Catalyst System Efficiency Below Threshold Bank 1  


MONITOR DESCRIPTION

The ECM uses air fuel ratio sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.

The first sensor, the air fuel ratio sensor (sensor 1), sends pre-catalyst information to the ECM. The second sensor, the air fuel ratio sensor (sensor 2), sends post-catalyst information to the ECM.

In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the output current of the air fuel ratio sensor (sensor 2) while performing active air fuel ratio control.

The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 30 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the cycle of the waveform for the air fuel ratio sensor (sensor 2) is long, the oxygen storage capacity is great. There is a direct correlation between the air fuel ratio sensor (sensor 2) and the oxygen storage capacity of the three-way catalytic converter.

The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, the ECM will illuminate the MIL and store a DTC.

This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P042000 Catalyst System Efficiency Below Threshold Bank 1 The oxygen storage capacity value is less than the standard value under active air fuel ratio control (1 trip detection logic).
·

Gas leak from exhaust system

·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 2)

·

Exhaust manifold (TWC: Front catalyst)

·

Front exhaust pipe assembly (TWC: Rear catalyst)

·

EGR valve assembly


Comes on DTC stored SAE: P0420

CATALYST LOCATION

A458467C02
1.375,3.354 1.167,3.354 1.167,3.354 0.844,2.063 false 1.542,0.458 1.333,0.458 1.333,0.458 0.99,1.073 false 2.51,3.49 2.635,3.49 2.635,3.49 2.906,3.031 false 4.115,0.573 3.906,0.573 3.906,0.573 3.417,2.344 false 5.885,1.906 6.073,1.906 6.073,1.906 6.531,0.76 false 1.427,3.292 1.708,3.51 0.281,0.219 10 false *1 4.229,0.531 4.542,0.688 0.313,0.156 10 false *2 5.698,1.854 6.01,2.01 0.313,0.156 10 false *3 1.604,0.396 1.844,0.615 0.24,0.219 10 false *4 2.292,3.438 2.604,3.594 0.313,0.156 10 false *5
*1 Exhaust Manifold (TWC: Front Catalyst) *2 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*3 Tail Exhaust Pipe Assembly *4 Air Fuel Ratio Sensor (Sensor 1)
*5 Air Fuel Ratio Sensor (Sensor 2) - -


NOTICE:

When replacing the exhaust manifold (*1) and the front exhaust pipe assembly (*2) in order to replace the three-way catalytic converter, it is not necessary to replace the air fuel ratio sensor (sensor 1) (*4) and the air fuel ratio sensor (sensor 2) (*5).


MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor (sensor 1)
Air fuel ratio sensor (sensor 2)
Required Sensors/Components (Related) Intake air temperature sensor
Mass air flow meter sub-assembly
Crankshaft position sensor
Engine coolant temperature sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Battery voltage 11 V or higher
Intake air temperature -10°C (14°F) or higher
Engine coolant temperature 75°C (167°F) or higher
Atmospheric pressure 76 kPa(abs) [11 psi(abs)] or higher
Idling Off
Engine speed Less than 3200 rpm
Air fuel ratio sensor (sensor 1) status Activated
Fuel system status Closed loop
Engine load 10% or higher, and less than 100%
All of the following conditions are met 1, 2 and 3
1. Mass air flow 6 gm/sec or more, and less than 75 gm/sec
2. Front catalyst temperature (estimated) 580°C (1076°F) or higher, and below 800°C (1472°F)
3. Rear catalyst temperature (estimated) 480°C (896°F) or higher, and below 700°C (1292°F)

CONFIRMATION DRIVING PATTERN

A414842E05
1.323,0.865 1.781,0.375 1.781,0.375 2.01,0.375 false 2.063,0.292 5.427,0.49 3.365,0.198 10 false Between 75 to 100 km/h 0.698,1.135 4.063,1.333 3.365,0.198 10 false 60 km/h 0.896,2.219 4.26,2.417 3.365,0.198 10 false Idling 0.156,2.427 3.521,2.625 3.365,0.198 10 false Ignition Switch off 1.656,2.094 5.021,2.292 3.365,0.198 10 false [A] 2.573,1.01 5.938,1.208 3.365,0.198 10 false [B]* 3.479,2.104 6.844,2.302 3.365,0.198 10 false [D] 4.365,1.01 4.823,1.229 0.458,0.219 10 false [E]* 6.135,0.625 6.531,0.854 0.396,0.229 10 false [G]* 3.344,2.74 3.948,3.156 0.604,0.417 10 false Warming up 4.125,2.729 4.854,3.188 0.729,0.458 10 false 10 minutes or more 3.146,3.146 3.469,3.417 0.323,0.271 10 false [C] 1.49,2.729 2.094,3.146 0.604,0.417 10 false Warming up 2.323,2.74 3.052,3.198 0.729,0.458 10 false 10 minutes or more 6.771,3.146 7.094,3.417 0.323,0.271 10 false [H] 5.01,3.156 5.333,3.427 0.323,0.271 10 false [F] 5.906,2.729 6.635,3.188 0.729,0.458 10 false 10 minutes or more 1.365,3.458 6.813,3.719 5.448,0.26 10 false *: Drive the vehicle while keeping the engine load as constant as possible 0.344,0.229 3.708,0.427 3.365,0.198 10 false Vehicle Speed 6.74,3.417 7.125,3.646 0.385,0.229 10 false Time

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with the shift lever in P or neutral [A].

HINT:

In order to keep the idle stable, turn the A/C and all other electric loads off and do not perform any shift operations.


9.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


10.

Turn the ignition switch off and wait for at least 30 seconds [C].

11.

Turn the ignition switch to ON.

12.

Turn the GTS on.

13.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [D].

14.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


15.

Enter the following menus: Powertrain / Engine / Trouble Codes [F].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

18.

Input the DTC: P042000.

19.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform the following procedure.



20.

Drive the vehicle at a speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes or more [G].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


21.

Enter the following menus: Powertrain / Engine / Trouble Codes [H].

22.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



23.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

24.

Input the DTC: P042000.

25.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




CAUTION / NOTICE / HINT

HINT:
·

If a malfunction cannot be found when troubleshooting DTC P042000, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P017100 (System Too Lean) and P017200 (System Too Rich).

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P042000)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P042000 and other DTCs are output A
P042000 is output B


HINT:

If any DTCs other than P042000 are output, troubleshoot those DTCs first.




A

GO TO DTC CHART

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

Pre-procedure1

a.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.


b.

Warm up the air fuel ratio sensors at an engine speed of 2500 rpm for 90 seconds.


Procedure1

c.

Change the fuel injection volume using the GTS, and monitor the output current of the air fuel ratio sensor (sensor 1) (A/F (O2) Sensor Current B1S1) and air fuel ratio sensor (sensor 2) (A/F (O2) Sensor Current B1S2) displayed on the GTS.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
Coolant Temperature
Injection Volume
A/F (O2) Sensor Current B1S1
A/F (O2) Sensor Current B1S2
50004 372 8 205,277,230,564
HINT:
·

The Active Test "Control the Injection Volume for A/F Sensor" can be used to lower the fuel injection volume by 12.5% or increase the injection volume by 12.5%.

·

The air fuel ratio sensor (sensor 1) is displayed as A/F (O2) Sensor Current B1S1, and the air fuel ratio sensor (sensor 2) is displayed as A/F (O2) Sensor Current B1S2 on the GTS.

·

The air fuel ratio sensor (sensor 1) has an output delay of a few seconds and the air fuel ratio sensor (sensor 2) has a maximum output delay of approximately 20 seconds.

·

If the sensor output current does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard:
GTS Display
(Sensor)
Injection Volume Status Current
A/F (O2) Sensor Current B1S1
(Air fuel ratio (sensor 1))
12.5% Rich Below -0.075 mA
-12.5% Lean Higher than 0.037 mA
A/F (O2) Sensor Current B1S2
(Air fuel ratio (sensor 2))
12.5% Rich Below -0.86 mA
-12.5% Lean Higher than 0.33 mA



Post-procedure1

d.

None.


Result:
Status A/F (O2) Sensor Current B1S1 Status A/F (O2) Sensor Current B1S2 Actual air fuel ratio, air fuel ratio sensor (sensor 1) and air fuel ratio sensor (sensor 2) condition Main Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal
·

Three-way catalytic converter

·

Gas leak from exhaust system

·

EGR valve assembly


A
Lean Lean/Rich Air fuel ratio sensor (sensor 1) malfunction
·

Air fuel ratio sensor (sensor 1)


B
Rich Lean/Rich Air fuel ratio sensor (sensor 1) malfunction
·

Air fuel ratio sensor (sensor 1)


B
Lean/Rich Lean Air fuel ratio sensor (sensor 2) malfunction
·

Air fuel ratio sensor (sensor 2)

·

Gas leak from exhaust system


C
Lean/Rich Rich Air fuel ratio sensor (sensor 2) malfunction
·

Air fuel ratio sensor (sensor 2)

·

Gas leak from exhaust system


C
Lean Lean Actual air fuel ratio lean
·

Extremely lean actual air fuel ratio

·

Gas leak from exhaust system

·

EGR valve assembly


D
Rich Rich Actual air fuel ratio rich
·

Extremely rich actual air fuel ratio

·

Gas leak from exhaust system

·

EGR valve assembly


D


Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor (sensor 1) output current (A/F (O2) Sensor Current B1S1) is consistently higher than 0.037 mA, and the air fuel ratio sensor (sensor 2) output current (A/F (O2) Sensor Current B1S2) is consistently higher than 0.33 mA.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor (sensor 1) output current (A/F (O2) Sensor Current B1S1) is consistently below -0.075 mA, and the air fuel ratio sensor (sensor 2) output current (A/F (O2) Sensor Current B1S2) is consistently below -0.86 mA.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output current of the air fuel ratio sensor (sensor 1) or air fuel ratio sensor (sensor 2) alternate correctly.


HINT:

Refer to "Data List / Active Test" [A/F (O2) Sensor Current B1S1, A/F (O2) Sensor Current B1S2].

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST



A

3.CHECK FOR EXHAUST GAS LEAK

B

6.REPLACE AIR FUEL RATIO SENSOR (SENSOR 1)

C

7.CHECK FOR EXHAUST GAS LEAK

D

9.CHECK FOR EXHAUST GAS LEAK
3.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks in exhaust system.



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

28.REPAIR OR REPLACE EXHAUST SYSTEM
4.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

Pre-procedure1

a.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.

HINT:

The A/C switch and all accessories should be off.



Procedure1

b.

Check the engine idling condition and Intake Manifold Absolute Pressure values in the Data List while performing the Active Test.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
Engine Speed
Intake Manifold Absolute Pressure
Coolant Temperature
EGR Step Position
50004 372 25 211,385,205,386
NOTICE:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

The value of Intake Manifold Absolute Pressure and Engine Speed change in response to EGR step position.


Standard:
- Control the EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Idling condition Steady idling Idling changes from steady to rough idling or engine stalls
Intake Manifold Absolute Pressure
(Data List)
Intake Manifold Absolute Pressure value is 18 to 38 kPa(abs)
(2.6 to 5.5 psi(abs))
(EGR valve is fully closed)
Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed


HINT:

During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.



Post-procedure1

c.

None.


Result:
Proceed to
OK
NG



OK

31.REPLACE EXHAUST MANIFOLD (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

NG

5.INSPECT EGR VALVE ASSEMBLY
5.INSPECT EGR VALVE ASSEMBLY

Pre-procedure1

a.

Procedure1

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.



Post-procedure1

c.

None.


Result:
Proceed to
OK
NG



OK

31.REPLACE EXHAUST MANIFOLD (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)

NG

REPLACE EGR VALVE ASSEMBLY

Click hereEngine / Hybrid System>M15A-FKS (EMISSION CONTROL)>EGR VALVE>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



6.REPLACE AIR FUEL RATIO SENSOR (SENSOR 1)
HINT:

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR (for Sensor 1)>REMOVAL

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

29.CLEAR DTC
7.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks in exhaust system.



Result:
Proceed to
OK
NG



OK

8.REPLACE AIR FUEL RATIO SENSOR (SENSOR 2)

NG

28.REPAIR OR REPLACE EXHAUST SYSTEM
8.REPLACE AIR FUEL RATIO SENSOR (SENSOR 2)
HINT:

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR (for Sensor 2)>REMOVAL

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 2).

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

29.CLEAR DTC
9.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks in exhaust system.



Result:
Proceed to
OK
NG



OK

10.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

28.REPAIR OR REPLACE EXHAUST SYSTEM
10.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

Pre-procedure1

a.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.

HINT:

The A/C switch and all accessories should be off.



Procedure1

b.

Check the engine idling condition and Intake Manifold Absolute Pressure values in the Data List while performing the Active Test.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
Engine Speed
Intake Manifold Absolute Pressure
Coolant Temperature
EGR Step Position
50004 372 25 211,385,205,386
NOTICE:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

The value of Intake Manifold Absolute Pressure and Engine Speed change in response to EGR step position.


Standard:
- Control the EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Idling condition Steady idling Idling changes from steady to rough idling or engine stalls
Intake Manifold Absolute Pressure
(Data List)
Intake Manifold Absolute Pressure value is 18 to 38 kPa(abs)
(2.6 to 5.5 psi(abs))
(EGR valve is fully closed)
Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed


HINT:

During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.



Post-procedure1

c.

None.


Result:
Proceed to
OK
NG



OK

15.READ VALUE USING GTS (MASS AIR FLOW SENSOR)

NG

11.INSPECT EGR VALVE ASSEMBLY
11.INSPECT EGR VALVE ASSEMBLY

Pre-procedure1

a.

Procedure1

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.



Post-procedure1

c.

None.


Result:
Proceed to
OK
NG



OK

12.CHECK PCV VALVE AND HOSE CONNECTIONS

NG

REPLACE EGR VALVE ASSEMBLY

Click hereEngine / Hybrid System>M15A-FKS (EMISSION CONTROL)>EGR VALVE>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



12.CHECK PCV VALVE AND HOSE CONNECTIONS
A458471

a.

Check the PCV hose connections.



OK:

PCV hose and PCV valve are connected correctly and are not damaged.


Result:
Proceed to
OK
NG



OK

13.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE PCV VALVE OR HOSE

13.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>M15A-FKS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks in intake system.



Result:
Proceed to
OK
NG



OK

14.READ VALUE USING GTS (COOLANT TEMPERATURE)

NG

REPAIR OR REPLACE INTAKE SYSTEM
HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



14.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Read the Data List twice, when the engine is both cold and warmed up.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
Standard:
GTS Display Condition Specified Condition
Coolant Temperature Cold engine Same as ambient air temperature
Warm engine Between 75 and 100°C (167 and 212°F)



Result:
Proceed to
OK
NG



OK

15.READ VALUE USING GTS (MASS AIR FLOW SENSOR)

NG

REPLACE ENGINE COOLANT TEMPERATURE SENSOR

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



15.READ VALUE USING GTS (MASS AIR FLOW SENSOR)

Pre-procedure1

a.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off and shift position N.


Procedure1

b.

Read the Mass Air Flow Sensor while maintaining an engine speed of 3000 rpm.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Mass Air Flow Sensor
Coolant Temperature
50003 372 211,215,205
HINT:

During charge control, the engine speed is set at idle. Therefore, the engine speed will not increase when the accelerator pedal is depressed. In this case, read the Data List after charge control has completed.



Post-procedure1

c.

None.


Result:
Result Proceed to
The value of Mass Air Flow Sensor is between 4.0 gm/sec and 8.0 gm/sec A
None of the above conditions are met B



A

16.CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)

B

20.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
16.CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)

OK

17.CHECK FUEL PRESSURE (FOR HIGH PRESSURE SIDE)

NG

27.CHECK FUEL LINE
17.CHECK FUEL PRESSURE (FOR HIGH PRESSURE SIDE)

OK

18.INSPECT IGNITION SYSTEM

NG

27.CHECK FUEL LINE
18.INSPECT IGNITION SYSTEM

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:

If the spark plugs or ignition system malfunctions, engine misfire may occur. The misfire count can be read using the GTS. Enter the following menus: Powertrain / Engine / Data List / Misfire Count Cylinder #1 to Misfire Count Cylinder #3.


Result:
Proceed to
OK
NG



OK

19.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)

NG

REPAIR OR REPLACE IGNITION SYSTEM
HINT:

Perform "Inspection After Repair" after repairing or replacing the ignition system.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



19.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
a.

Check the injection and volume.

HINT:
·

Refer to the fuel injector assembly inspection procedure.

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL INJECTOR>INSPECTION

·

If the fuel injector assemblies malfunction, engine misfire may occur. The misfire count can be read using the GTS. Enter the following menus: Powertrain / Engine / Data List / Misfire Count Cylinder #1 to Misfire Count Cylinder #3.




Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)

NG

REPLACE FUEL INJECTOR ASSEMBLY

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL INJECTOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



20.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

HINT:

Repair any problems.



Result:
Proceed to
NEXT



NEXT

21.CLEAR DTC
21.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

22.CHECK WHETHER DTC OUTPUT RECURS (DTC P042000)
22.CHECK WHETHER DTC OUTPUT RECURS (DTC P042000)

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Post-procedure1

c.

None.


Result:
Result Proceed to
DTCs are not output A
P042000 is output B



A

END

B

23.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
23.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

Pre-procedure1

a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D23-4 (VCC) - D51-78 (VCVG) Always Below 1 Ω
D23-3 (FG) - D51-101 (VG) Always Below 1 Ω
D23-2 (E2G) - D51-79 (E2G) Always Below 1 Ω
D23-4 (VCC) or D51-78 (VCVG) - Body ground and other terminals Always 10 kΩ or higher
D23-3 (FG) or D51-101 (VG) - Body ground and other terminals Always 10 kΩ or higher
D23-2 (E2G) or D51-79 (E2G) - Body ground and other terminals Always 10 kΩ or higher



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

24.REPLACE MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.REPLACE MASS AIR FLOW METER
HINT:
·

If the result of the inspection performed in steps 15 (READ VALUE USING GTS (MASS AIR FLOW SENSOR)) indicated no problem, proceed to the next step without replacing the mass air flow meter.

·

Perform "Inspection After Repair" after replacing the mass air flow meter.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

25.CLEAR DTC
25.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

26.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
26.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Post-procedure1

c.

None.


Result:
Result Proceed to
DTCs are not output A
P042000 is output B



A

END

B

27.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.


Result:
Proceed to
OK
NG



OK

GO TO FUEL PUMP CONTROL CIRCUIT

NG

REPAIR OR REPLACE FUEL SYSTEM

28.REPAIR OR REPLACE EXHAUST SYSTEM
HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

29.CLEAR DTC
29.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

30.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
30.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Post-procedure1

c.

None.


Result:
Result Proceed to
DTCs are not output A
P042000 is output B



A

END

B

31.REPLACE EXHAUST MANIFOLD (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)
31.REPLACE EXHAUST MANIFOLD (TWC: FRONT CATALYST) AND FRONT EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST)
NOTICE:

When replacing the exhaust manifold and the front exhaust pipe assembly in order to replace the three-way catalytic converter, it is not necessary to replace the air fuel ratio sensor (sensor 1) and the air fuel ratio sensor (sensor 2).


HINT:

Confirm the replacement parts, referring to the illustration in the Catalyst Location.


a.

Replace the exhaust manifold (TWC: Front catalyst).

Click hereEngine / Hybrid System>M15A-FKS (INTAKE / EXHAUST)>EXHAUST MANIFOLD>REMOVAL


b.

Replace the front exhaust pipe assembly (TWC: Rear catalyst).

Click hereEngine / Hybrid System>M15A-FKS (INTAKE / EXHAUST)>EXHAUST PIPE>REMOVAL


Result:
Proceed to
NEXT



NEXT

END