Home › Engine / Hybrid System › M15A-FKS (FUEL) › FUEL INJECTOR › 2020.03–2020.07
RM36W0E _51 Engine / Hybrid System _088660 M15A-FKS FUEL _0422099 FUEL INJECTOR A

M15A-FKS FUEL  FUEL INJECTOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of fuel injector assembly Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 23801P 5.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 6.SEPARATE ENGINE WIRE

NOTICE:

When replacing the fuel delivery pipe, it is necessary to replace the No. 1 fuel pipe sub-assembly with a new one.


a.

Disengage the clamp and disconnect the connector from the fuel pressure sensor.

A459799


b.

Disengage the clamp and disconnect the 3 fuel injector assembly connectors from the fuel injector assembly.

NOTICE:

Make sure to disconnect the connectors carefully.



Hide 23845G 7.REMOVE FUEL DELIVERY INSULATOR

a.
A464830

Remove the fuel delivery insulator.


Hide 23814B 8.REMOVE FUEL DELIVERY PIPE

a.
A464831

Remove the 3 bolts and fuel delivery pipe with the 3 fuel injector assemblies from the cylinder head sub-assembly.

NOTICE:
·

Make sure not to touch or strike the tips of the fuel injector assemblies.

·

Pull and remove the fuel delivery pipe in a straight line without tilting it.




Hide 23250 9.REMOVE FUEL INJECTOR ASSEMBLY

a.
A401662N02
2.052,2.052 2.823,2.25 0.771,0.198 10 false No.3

Secure the fuel delivery pipe in a vise between aluminum plates and pull out the 3 fuel injector assemblies.

NOTICE:
·

Pull and remove each fuel injector assembly in a straight line to avoid damaging the seal surface of the fuel delivery pipe O-ring.

·

After removing the fuel injector assemblies, remove any O-rings, No. 1 fuel injector back-up rings and No. 3 fuel injector back-up rings remaining on the fuel delivery pipe side.

·

Attach a tag or label with the corresponding cylinder number to each fuel injector assembly so that they can be installed to their original locations.

·

Cover the tip of each fuel injector assembly to prevent it from being damaged.




b.

Remove the nozzle holder clamp from each fuel injector assembly.


c.

Using needle nose pliers, remove the No. 3 fuel injector back-up ring from each fuel injector assembly.

NOTICE:

Do not damage the area that contacts the O-ring.



d.

Remove the O-ring and No. 1 fuel injector back-up ring from each fuel injector assembly.


e.

Remove the C-ring from each fuel injector assembly.


f.

Remove the injector vibration insulator from each fuel injector assembly.


Hide 23255A 10.REMOVE FUEL INJECTOR SEAL

a.
A464832

Using the tip of needle nose pliers, pinch and pull the fuel injector seal at several points to stretch it.

NOTICE:
·

Excessively pinching the fuel injector seal may damage the groove of the fuel injector assembly.

·

If a fuel injector assembly is dropped or the tip of the fuel injector assembly is struck, replace it with a new one.




b.

Remove the fuel injector seal from each fuel injector assembly.