Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › SFI SYSTEM › 2020.03–2020.07
RM36W0E _51 Engine / Hybrid System _087499 M15A-FKS ENGINE CONTROL _0418534 SFI SYSTEM J

M15A-FKS ENGINE CONTROL  SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal ST1 of the ignition switch assembly*1 or terminal STAR of the certification ECU (smart key ECU assembly)*2 to the park/neutral position switch assembly*3 or clutch start switch assembly*4 and to terminal STA of the ECM (STA signal).

*1: w/o Entry and Start System

*2: w/ Entry and Start System

*3: for Continuously Variable Transaxle Models

*4: for Manual Transaxle Models

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.

Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B




A

2.READ VALUE USING GTS (STARTER SW)

B

23.READ VALUE USING GTS (STARTER SW)
2.READ VALUE USING GTS (STARTER SW)
a.

Fully depress the clutch pedal (for Manual Transaxle Models with Clutch Start System).


b.

Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11
OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Result Proceed to
NG (for Continuously Variable Transaxle Models) A
NG (for Manual Transaxle Models) B
OK C



A

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

B

9.INSPECT CLUTCH START SWITCH ASSEMBLY

C

15.INSPECT ST NO. 1 RELAY
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>PARK / NEUTRAL POSITION SWITCH>INSPECTION

Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

4.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

B

6.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

C

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Disconnect the certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D45-5 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω
A54-30 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
H45-3 (STA), 2 (ST NO. 1 relay), D45-5 (L) or A54-30 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-10 (STAR) - D45-4 (B) Always Below 1 Ω
H45-10 (STAR) - A54-23 (NSW) Always Below 1 Ω
H45-10 (STAR), D45-4 (B) or A54-23 (NSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D45-5 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω
A54-30 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
D45-5 (L), 2 (ST NO. 1 relay) or A54-30 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the ignition switch assembly connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-4 (ST2) - D45-4 (B) Always Below 1 Ω
H54-4 (ST2) - A54-23 (NSW) Always Below 1 Ω
H54-4 (ST2), D45-4 (B) or A54-23 (NSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT IGNITION SWITCH ASSEMBLY

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

9.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.


Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

10.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

B

12.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

C

REPLACE CLUTCH START SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the clutch start switch assembly connector.


b.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Disconnect the certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-1 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω
A54-30 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
H45-3 (STA), 2 (ST NO. 1 relay), A64-1 (L) or A54-30 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - CLUTCH START SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - CLUTCH START SWITCH ASSEMBLY - ECM)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-10 (STAR) - A64-2 (B) Always Below 1 Ω
H45-10 (STAR) or A64-2 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the clutch start switch assembly connector.


b.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-1 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω
A54-30 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
A64-1 (L), 2 (ST NO. 1 relay) or A54-30 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the ignition switch assembly connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-4 (ST2) - A64-2 (B) Always Below 1 Ω
H54-4 (ST2) or A64-2 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>M15A-FKS (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

15.INSPECT ST NO. 1 RELAY

OK

16.INSPECT STARTER ASSEMBLY

NG

REPLACE ST NO. 1 RELAY

16.INSPECT STARTER ASSEMBLY
a.

Inspect the starter assembly.

Click hereEngine / Hybrid System>M15A-FKS (STARTING)>STARTER>INSPECTION


Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)

NG

17.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (ST NO. 1 relay) - D54-1 (ST) Always Below 1 Ω
3 (ST NO. 1 relay) or D54-1 (ST) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

18.CHECK TERMINAL VOLTAGE (BATTERY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK TERMINAL VOLTAGE (BATTERY - STARTER ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Disconnect the starter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) battery terminal - D80-1 (B) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

19.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)
A457773C03
0.115,0.125 0.427,0.281 0.313,0.156 10 false *1 2.063,2.333 2.375,2.49 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 1 Relay


a.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (ST NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST NO. 1 RELAY)

20.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
a.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ST NO. 1 relay) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for Continuously Variable Transaxle Models) A
OK (for Manual Transaxle Models) B
NG C



A

21.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

B

22.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - CLUTCH START SWITCH ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ST NO. 1 relay) - D45-5 (L) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - CLUTCH START SWITCH ASSEMBLY)
a.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ST NO. 1 relay) - A64-1 (L) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.READ VALUE USING GTS (STARTER SW)
a.

Fully depress the clutch pedal (for Manual Transaxle Models with Clutch Start System).


b.

Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11
OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY - ECM)