The air fuel ratio sensor (sensor 1) is constructed of 2 zirconia cells (VS cell and IP cell), a detection chamber and a heater. It detects fuel injection volume control feedback and three-way catalyst deterioration by detecting the oxygen concentration level in the exhaust gas.
The ECM compares the VS cell voltage and target voltage (0.45 V) and outputs the Ip current for averaging the oxygen concentration level in the detection chamber.
The VS cell operates through sufficient heat and current being supplied, and a potential difference is created based on the difference in oxygen ion concentration level between the standard oxygen electrode (Platinum Element) and detection chamber.
The IP cell controls the oxygen concentration level of the detection chamber.
If the Ip current is positive, the oxygen ions in the detection chamber are sent out. If the Ip current is negative, they are sent in.
The detection chamber is between the VS cell and IP cell.
The heater heats the zirconia element through the alumina to activate the air fuel ratio sensor (sensor 1).
If the exhaust gas is at the stoichiometric air-fuel ratio, the Ip current will be 0 mA and the VS cell will be at 0.45 V.
If the exhaust gas is rich, the ECM generates a negative Ip current in order to increase the oxygen concentration level in the detection chamber.
If the exhaust gas is lean, the ECM generates a positive Ip current in order to decrease the oxygen concentration level in the detection chamber.
| *1 | Exhaust gas | *2 | Cover |
| *3 | Element | *4 | Platinum Element |
| *5 | Alumina | *6 | Element Cross Sectional Diagram |
| *7 | Heater | *8 | Zirconia (IP cell) |
| *9 | Zirconia (VS cell) | - | - |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P013001 | O2 (A/F) Sensor Circuit Bank 1 Sensor 1 General Electrical Failure | Refer to the chart below (2 trip detection logic). | ·
Open or short in air fuel ratio sensor (sensor 1) circuit ·
Air fuel ratio sensor (sensor 1) ·
ECM |
Comes on | DTC stored | SAE Code: P0130 |
| P22371B | A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Resistance Above Threshold | The air fuel ratio sensor (sensor 1) impedance is higher than 185.209 Ω (2 trip detection logic). | ·
Open or short in air fuel ratio sensor (sensor 1) circuit ·
Air fuel ratio sensor (sensor 1) ·
ECM |
Comes on | DTC stored | SAE Code: P2238 |
| P013001 Detection Conditions | Malfunction Condition | ||||||
| VS+ Low | COM Low | IP+ Low | VS+ High | COM High | IP+ High | ||
| Diagnosis Condition | Auxiliary battery voltage 10.5 V or higher | ○ | ○ | ○ | ○ | ○ | ○ |
| 5 seconds or more after turning the ignition switch to ON | ○ | ○ | ○ | ○ | ○ | ○ | |
| Malfunction Status | VS+ terminal voltage below 0.3 V | ○ | - | - | - | - | - |
| COM terminal voltage below 0.3 V | - | ○ | - | - | - | - | |
| IP+ terminal voltage below 0.3 V | - | - | ○ | - | - | - | |
| Short in VS+ terminal circuit to power source circuit | - | - | - | ○ | - | - | |
| Short in COM terminal circuit to power source circuit | - | - | - | - | ○ | - | |
| Short in IP+ terminal circuit to power source circuit | - | - | - | - | - | ○ | |
| Malfunction Duration | 5 seconds or more | 5 seconds or more | 5 seconds or more | 5 seconds or more | 5 seconds or more | 5 seconds or more | |
| P013001 Detection Conditions | Malfunction Condition | ||||
| Short in either VS+ or COM | Open circuit in VS+ | Open circuit in IP+ | Open circuit in COM | ||
| Diagnosis Condition | Auxiliary battery voltage 10.5 V or higher | ○ | ○ | ○ | ○ |
| 5 seconds or more after turning the ignition switch to ON | ○ | ○ | ○ | ○ | |
| Air fuel ratio sensor (sensor 1) impedance smaller than 100 Ω | ○ | - | - | - | |
| Air fuel ratio sensor (sensor 1) heater duty 20% or higher for 10 seconds or more | - | ○ | - | - | |
| Air fuel ratio sensor (sensor 1) impedance smaller than 400 Ω | - | - | ○ | ○ | |
| Malfunction Status | Difference between VS+ terminal voltage and COM terminal voltage below 0.2 V | ○ | - | - | - |
| VS+ terminal voltage exceeds 4.6 V | - | ○ | - | - | |
| Difference between COM sweep current (sink) and COM sweep current (source ) is 0.4 mA or higher | - | - | ○ | - | |
| COM terminal voltage is below 2.3 V or exceeds 2.7 V | - | - | - | ○ | |
| Malfunction Duration | 5 seconds or more | 5 seconds or more | 5 seconds or more | 5 seconds or more | |
These DTCs are stored when there is an open or short in the air fuel ratio sensor (sensor 1) circuit, or the air fuel ratio sensor (sensor 1) output value is abnormal. The voltage or current of the air fuel ratio sensor (sensor 1) is monitored while the ignition switch is ON or the engine is running, and the impedance (impedance is an electrical term that indicates the difficulty of flow of current) is checked while engine running. If the voltage or current of the air fuel ratio sensor (sensor 1) is outside the normal range, or the impedance is outside the normal range, the ECM illuminates the MIL and stores a DTC.
| Required Sensors/Components (Main) | Air fuel ratio sensor (sensor 1) |
| Required Sensors/Components (Related) | Engine coolant temperature sensor
Crankshaft position sensor |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Start the engine.
Wait 5 minutes.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P013001 or P22371B.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Refer to DTC P003012.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>P003012
Inspect the fuses for circuits related to this system before performing the following procedure.
Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY
(Select Powertrain in Health Check and then check the time stamp data.)
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Refer to "Data List / Active Test" [A/F (O2) Sensor Current B1S1].
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.
Pre-procedure1
Disconnect the D40 air fuel ratio sensor (sensor 1) connector.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D40-1 (IP+) - Body ground | Ignition switch ON | 2.4 to 2.6 V |
| D40-2 (COM) - Body ground | Ignition switch ON | 2.4 to 2.6 V |
| D40-3 (VS+) - Body ground | Ignition switch ON | 4.1 to 5.0 V |
| D40-1 (IP+) - D40-2 (COM) | Ignition switch ON | -0.2 to 0.2 V |
| D40-3 (VS+) - D40-2 (COM) | Ignition switch ON | 1.7 to 2.6 V |
Post-procedure1
None.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR (for Sensor 1)>REMOVAL
Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
NG
Pre-procedure1
Disconnect the D40 air fuel ratio sensor (sensor 1) connector.
Disconnect the D52 ECM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D40-4 (HA1A) - D52-28 (HA1A) | Always | Below 1 Ω |
| D40-1 (IP+) - D52-100 (IP+) | Always | Below 1 Ω |
| D40-2 (COM) - D52-99 (COM) | Always | Below 1 Ω |
| D40-3 (VS+) - D52-98 (VS+) | Always | Below 1 Ω |
| D40-4 (HA1A) or D52-28 (HA1A) - Body ground and other terminals | Always | 10 kΩ or higher |
| D40-1 (IP+) or D52-100 (IP+) - Body ground and other terminals | Always | 10 kΩ or higher |
| D40-2 (COM) or D52-99 (COM) - Body ground and other terminals | Always | 10 kΩ or higher |
| D40-3 (VS+) or D52-98 (VS+) - Body ground and other terminals | Always | 10 kΩ or higher |
Post-procedure1
None.
| Proceed to |
|---|
| OK |
| NG |
OK
NG