Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › SFI SYSTEM
RM36W0E _51 Engine / Hybrid System _087500 M15A-FXE ENGINE CONTROL _0418535 SFI SYSTEM J

M15A-FXE ENGINE CONTROL  SFI SYSTEM  Fuel Injector Circuit  


DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM

A457720E01
1.458,1.688 1.917,1.885 0.458,0.198 10 false IGP 2.479,1.052 2.938,1.25 0.458,0.198 10 false INJ 1.51,3.469 1.969,3.667 0.458,0.198 10 false IGPD 1.531,5.219 1.99,5.417 0.458,0.198 10 false IG1 0.479,4.229 0.844,4.677 0.365,0.448 10 false IGP-MAIN 0.458,5.448 0.885,5.917 0.427,0.469 10 false BATT-MAIN 1.313,5.083 1.771,5.281 0.458,0.198 10 false 8 1.135,5.344 1.594,5.542 0.458,0.198 10 false *2 1.323,5.646 1.781,5.844 0.458,0.198 10 false H54 1.313,5.813 3.24,6.26 1.927,0.448 10 false Ignition Switch Assembly*2 5.125,6.271 5.583,6.469 0.458,0.198 10 false A53 5.135,4.635 5.594,4.833 0.458,0.198 10 false D52 5.125,2.813 5.583,3.01 0.458,0.198 10 false D52 5.135,0.865 5.594,1.063 0.458,0.198 10 false D52 1.24,3.479 1.698,3.677 0.458,0.198 10 false 24 1.125,3.74 1.583,3.938 0.458,0.198 10 false *1 1.313,4.021 1.771,4.219 0.458,0.198 10 false H45 1.313,4.188 3.115,4.646 1.802,0.458 10 false Certification ECU (Smart Key ECU Assembly)*1 1.063,1.208 1.521,1.406 0.458,0.198 10 false 1 1.063,0.75 1.521,0.948 0.458,0.198 10 false 3 2,0.76 2.458,0.958 0.458,0.198 10 false 5 2,1.198 2.458,1.396 0.458,0.198 10 false 2 3.583,1.26 4.042,1.458 0.458,0.198 10 false E1 3.615,0.75 4.073,0.948 0.458,0.198 10 false 1 3.583,2.688 4.042,2.885 0.458,0.198 10 false 1 3.573,4.5 4.031,4.698 0.458,0.198 10 false 1 4.75,0.729 5.208,0.927 0.458,0.198 10 false 2 4.76,2.688 5.219,2.885 0.458,0.198 10 false 2 4.771,4.51 5.229,4.708 0.458,0.198 10 false 2 3.802,4.542 4.26,4.74 0.458,0.198 10 false #3 3.802,2.719 4.26,2.917 0.458,0.198 10 false #2 3.813,0.771 4.271,0.969 0.458,0.198 10 false #1 4.406,0.771 4.865,0.969 0.458,0.198 10 false #10 4.417,2.719 4.875,2.917 0.458,0.198 10 false #20 4.406,4.542 4.865,4.74 0.458,0.198 10 false #30 5.188,0.656 5.646,0.854 0.458,0.198 10 false 96 5.177,2.604 5.635,2.802 0.458,0.198 10 false 95 5.188,4.427 5.646,4.625 0.458,0.198 10 false 94 5.5,0.76 5.958,0.958 0.458,0.198 10 false #10 5.5,2.708 5.958,2.906 0.458,0.198 10 false #20 5.51,4.51 5.969,4.708 0.458,0.198 10 false #30 3.604,3.396 5.031,3.844 1.427,0.448 10 false Fuel Injector Assembly (No. 2 Cylinder) 3.604,3.219 4.063,3.417 0.458,0.198 10 false E2 3.583,1.438 5.01,1.885 1.427,0.448 10 false Fuel Injector Assembly (No. 1 Cylinder) 3.646,5.031 4.104,5.229 0.458,0.198 10 false E3 3.635,5.208 5.063,5.656 1.427,0.448 10 false Fuel Injector Assembly (No. 3 Cylinder) 5.521,6.177 5.979,6.375 0.458,0.198 10 false E1 5.208,6.073 5.667,6.271 0.458,0.198 10 false 6 6.063,7.031 6.521,7.229 0.458,0.198 10 false ECM 0.99,7.406 3.385,7.854 2.396,0.448 10 false *2: w/o Entry and Start System 0.99,7.073 3.385,7.521 2.396,0.448 10 false *1: w/ Entry and Start System 0.573,6.458 1.927,6.771 1.354,0.313 10 false Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT FUEL INJECTOR ASSEMBLY (POWER SOURCE)
a.

Disconnect the E1, E2 and E3 fuel injector connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E1-1 (#1) - Body ground Ignition switch ON 11 to 14 V
E2-1 (#2) - Body ground Ignition switch ON 11 to 14 V
E3-1 (#3) - Body ground Ignition switch ON 11 to 14 V


Result:
Result
OK
NG




OK

2.INSPECT FUEL INJECTOR ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (IGP RELAY - FUEL INJECTOR ASSEMBLY)
2.INSPECT FUEL INJECTOR ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)

NG

REPLACE FUEL INJECTOR ASSEMBLY

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL INJECTOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
a.

Disconnect the E1, E2 and E3 fuel injector assembly connectors.


b.

Disconnect the D52 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E1-2 (#10) - D52-96 (#10) Always Below 1 Ω
E2-2 (#20) - D52-95 (#20) Always Below 1 Ω
E3-2 (#30) - D52-94 (#30) Always Below 1 Ω
E1-2 (#10) or D52-96 (#10) - Body ground and other terminals Always 10 kΩ or higher
E2-2 (#20) or D52-95 (#20) - Body ground and other terminals Always 10 kΩ or higher
E3-2 (#30) or D52-94 (#30) - Body ground and other terminals Always 10 kΩ or higher


Result:
Result
OK
NG




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (IGP RELAY - FUEL INJECTOR ASSEMBLY)
a.

Remove the IGP relay from the No. 1 engine room relay block.


b.

Disconnect the E1, E2 and E3 fuel injector assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGP relay) - E1-1 (#1) Always Below 1 Ω
5 (IGP relay) - E2-1 (#2) Always Below 1 Ω
5 (IGP relay) - E3-1 (#3) Always Below 1 Ω
5 (IGP relay) or E1-1 (#1) - Body ground and other terminals Always 10 kΩ or higher
5 (IGP relay) or E2-1 (#2) - Body ground and other terminals Always 10 kΩ or higher
5 (IGP relay) or E3-1 (#3) - Body ground and other terminals Always 10 kΩ or higher


HINT:

If a short is detected in any of the above circuits, there may be a malfunction in the circuit of a connected ECU.


Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR