Home › Engine / Hybrid System › M15A-FXE (FUEL) › FUEL INJECTOR
RM36W0E _51 Engine / Hybrid System _088661 M15A-FXE FUEL _0422113 FUEL INJECTOR A

M15A-FXE FUEL  FUEL INJECTOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Replacement of fuel injector assembly

·

Replacement of No. 2 fuel pressure sensor (for low pressure side)


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 4.REMOVE EGR VALVE WITH EGR CCOLER ASSEMBLY

Hide 25624 5.REMOVE EGR VALVE ADAPTER

a.
A465995

Using an 8 mm socket wrench, remove the bolt.


b.

Disengage the guide to remove the EGR valve adapter.


Hide 23902 6.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A465996

Disconnect the fuel tube sub-assembly from the fuel delivery pipe sub-assembly.

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23814B 7.REMOVE FUEL DELIVERY PIPE

a.
A465997

Remove the 2 bolts and fuel delivery pipe with the 3 fuel injector assemblies from the cylinder head sub-assembly.

NOTICE:

Be careful not to drop the fuel injector assemblies when removing the fuel delivery pipe sub-assembly.



Hide 23891 8.REMOVE FUEL DELIVERY SPACER

a.
A465998

Remove the 2 fuel delivery spacers from the cylinder head sub-assembly.


Hide 23291 9.REMOVE INJECTOR VIBRATION INSULATOR

a.
A465999

Remove the 3 injector vibration insulators from the cylinder head sub-assembly.


Hide 82125N 10.REMOVE NO. 5 ENGINE WIRE

a.
A466000

Disconnect the 4 connectors from the 3 fuel injector assemblies and fuel pressure sensor.


b.

Disengage the 2 clamps to remove the No. 5 engine wire from the fuel delivery pipe.


Hide 23250 11.REMOVE FUEL INJECTOR ASSEMBLY

a.
A401652

Pull the 3 fuel injector assemblies out of the fuel delivery pipe.


b.
A401653

Remove the O-ring from each fuel injector assembly.


c.
A401654N01
2,0.417 2.771,0.615 0.771,0.198 10 false No. 1

Attach a tag or label with the corresponding cylinder number to each fuel injector assembly so that they can be installed to their original locations.

NOTICE:

Cover the fuel injector assemblies with plastic bags to prevent damage and contamination.