Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › SFI SYSTEM
RM36W0E _51 Engine / Hybrid System _087500 M15A-FXE ENGINE CONTROL _0418535 SFI SYSTEM C

M15A-FXE ENGINE CONTROL  SFI SYSTEM  P052400  Engine Oil Pressure Too Low  


DESCRIPTION

Variable oil pump control uses the engine oil pressure and temperature sensor and ECM to optimize the oil pressure and oil volume required by each component to reduce friction by monitoring the engine temperature and engine speed.

The ECM drives the oil pressure control valve assembly based on the oil pressure measured by the oil pressure sensor. The oil pressure is controlled by operating the oil pressure control valve assembly to regulate the amount of discharge oil.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P052400 Engine Oil Pressure Too Low When the engine is running, the oil pressure value output from the engine oil pressure and temperature sensor is less than the target value (1 trip detection logic).
·

Oil pump assembly

·

Engine oil pressure and temperature sensor

·

The engine oil level is low

·

The engine oil has deteriorated

·

ECM


Comes on DTC stored SAE Code: P0524

Related Data List/Freeze Frame Data
DTC No. Data List/Freeze Frame Data
P052400
·

Engine Speed

·

Engine Oil Temperature Sensor

·

Coolant Temperature

·

Engine Oil Pressure



MONITOR DESCRIPTION

The ECM monitors the oil pressure based on the signal output from the engine oil pressure and temperature sensor. The ECM illuminates the MIL and stores a DTC when the actual oil pressure is lower than the target oil pressure to the oil pump assembly.

MONITOR STRATEGY

Required Sensors/Components Oil pressure sensor
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

A403807E22
2.094,2.958 2.323,2.958 2.323,2.958 2.323,2.615 false 0.75,0.917 1.594,1.198 0.844,0.281 10 false 2500 rpm 0.99,1.76 1.833,2.042 0.844,0.281 10 false Idling 0.188,2.125 1.75,2.448 1.563,0.323 10 false Ignition Switch ON 2.219,1.646 3.063,1.927 0.844,0.281 10 false [A] 3.969,0.771 4.813,1.052 0.844,0.281 10 false [B] 5.188,2.021 6.031,2.302 0.844,0.281 10 false [C] 1.313,2.854 2.156,3.135 0.844,0.281 10 false Warming up 2.635,2.677 3.479,2.958 0.844,0.281 10 false 30 seconds 3.792,2.677 4.635,2.958 0.844,0.281 10 false 1 minute 5.833,2.906 6.677,3.188 0.844,0.281 10 false [D]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

9.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off [A].

10.

When the vehicle is stationery, gradually depress the accelerator pedal to increase the engine speed to 2500 rpm over a 30 second period, then run the engine speed at 2500 rpm for 1 minute before releasing the accelerator pedal to return to the idling speed [B].

11.

Repeat step [B] 3 times or more [C].

12.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

15.

Input the DTC: P052400.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.

·

If the judgment result is INCOMPLETE, perform steps [B] through [D] again.




CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY



HINT:
·

If the engine oil level is sufficient but a low engine oil level DTC is output, confirm with the customer whether engine oil was added after the vehicle had been driven with a low engine oil level.

·

If an incorrect engine oil viscosity is used, a DTC related to low oil pressure, etc., may be stored.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ENGINE OIL LEVEL

Click hereEngine / Hybrid System>M15A-FXE (LUBRICATION)>LUBRICATION SYSTEM>ON-VEHICLE INSPECTION

a.

Check the state of the oil level warning.

Result:
Result Proceed to
Engine oil level is within the specified range and oil level warning is not displayed A
Engine oil level is low and oil level warning is displayed B


HINT:

If the oil level warning is not displayed even though the engine oil level is below the Low mark, or the oil level warning is displayed even though the engine oil level is within the specified range, inspect the oil level sensor and related parts.




A

2.CHECK ENGINE OIL QUALITY

B

4.CHECK FOR ENGINE OIL LEAK
2.CHECK ENGINE OIL QUALITY

Click hereEngine / Hybrid System>M15A-FXE (LUBRICATION)>LUBRICATION SYSTEM>ON-VEHICLE INSPECTION

a.

Check that the engine oil is not contaminated with water, deteriorated, discolored or excessively thin.

OK:

The engine oil is not contaminated with water, deteriorated, discolored or excessively thin.



Result:
Proceed to
OK
NG



OK

6.CLEAR DTC

NG

3.REPLACE ENGINE OIL
3.REPLACE ENGINE OIL
HINT:
·

If the oil filter has exceeded the replacement period, replace the oil filter at the same time.



Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
4.CHECK FOR ENGINE OIL LEAK
a.

Check for engine oil leaks.

OK:

There are no engine oil leaks.


HINT:

If there are engine oil leaks, perform the following steps after repairing or replacing the malfunctioning parts.



Result:
Proceed to
NEXT



NEXT

5.ADD ENGINE OIL
5.ADD ENGINE OIL
a.

Add engine oil.

NOTICE:

Do not add engine oil to above the full level mark.



Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P052400)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P052400)

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Post-procedure1

c.

None.


Result:
Result Proceed to
P052400 is output A
DTCs are not output B



A

10.CHECK ENGINE OIL PRESSURE

B

8.READ VALUE USING GTS (ENGINE OIL PRESSURE)
8.READ VALUE USING GTS (ENGINE OIL PRESSURE)

Pre-procedure1

a.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

Procedure1

b.

Start the engine and warm it up until the engine oil temperature is 75 to 85°C (167 to 185°F), read the "Engine Oil Pressure" with the engine speed at 1500 rpm.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Engine Oil Temperature Sensor
Engine Oil Pressure
50003 372 211,261,103

Post-procedure1

c.

None.


Result:
Result Proceed to
The value of Engine Oil Pressure is 100 kPa or higher A
None of the above conditions are met B


HINT:

100 kPa = 1.0 kgf/cm2, 15 psi



A

9.READ VALUE USING GTS (ENGINE OIL PRESSURE)

B

10.CHECK ENGINE OIL PRESSURE
9.READ VALUE USING GTS (ENGINE OIL PRESSURE)

Pre-procedure1

a.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

Procedure1

b.

Start the engine and warm it up until the engine oil temperature is 75 to 85°C (167 to 185°F), read the "Engine Oil Pressure" with the engine speed at 2500 rpm.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Engine Oil Temperature Sensor
Engine Oil Pressure
50003 372 211,261,103

Post-procedure1

c.

None.


Result:
Result Proceed to
The value of Engine Oil Pressure is 200 kPa or higher A
None of the above conditions are met B


HINT:

200 kPa = 2.0 kgf/cm2, 29 psi



A

END

B

10.CHECK ENGINE OIL PRESSURE
10.CHECK ENGINE OIL PRESSURE

Pre-procedure1


b.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 3103

c.

Start the engine.


Procedure1

d.

Maintain "Coolant Temperature" at 90 to 95°C (194 to 203°F) for 3 minutes, and then read the oil pressure gauge value at 1500 rpm and 2500 rpm.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Coolant Temperature
50003 372 211,205
HINT:
·

Because the engine oil temperature cannot be checked when the engine oil pressure and temperature sensor is removed, refer to "Coolant Temperature".

·

Race the engine as necessary to maintain "Coolant Temperature" at 90 to 95°C (194 to 203°F).

·

If maintained for 3 minutes or more, the engine oil temperature may exceed 85°C (185°F).



Standard
Engine Speed Coolant Temperature Engine Oil Pressure Gauge Value
1500 rpm Maintained at 90 to 95°C (194 to 203°F) for 3 minutes
(Reference) Engine oil temperature: 75 to 85°C (167 to 185°F)
100 kPa (1.0 kgf/cm2, 15 psi) or higher
2500 rpm 200 kPa (2.0 kgf/cm2, 29 psi) or higher

HINT:

Be sure to clear the DTCs after reinstalling the oil pressure sensor (engine oil pressure and temperature sensor) or reconnecting the oil pressure sensor (engine oil pressure and temperature sensor) connector, as DTCs may be stored.



Post-procedure1

e.

None.


Result:
Proceed to
OK
NG



OK

REPLACE ENGINE OIL PRESSURE AND TEMPERATURE SENSOR

NG