Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › SFI SYSTEM
RM36W0E _51 Engine / Hybrid System _087499 M15A-FKS ENGINE CONTROL _0418534 SFI SYSTEM C

M15A-FKS ENGINE CONTROL  SFI SYSTEM  P001013  A Camshaft Position Actuator Bank 1 Circuit Open  


DESCRIPTION

The VVT (Variable Valve Timing) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing.

The cam timing oil control solenoid assembly (for intake camshaft) operates according to signals received from the ECM to control the position of the camshaft timing oil control valve assembly and supply engine oil. The camshaft timing oil control valve assembly moves when the ECM applies 12 V to the cam timing oil control solenoid assembly. The ECM changes the energizing time of the cam timing oil control solenoid assembly (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A321256E30
1.615,4.625 1.74,4.083 1.74,4.083 1.885,4.083 false 2.594,4.948 3.083,5.25 3.083,5.25 3.167,5.25 true 2.865,4.719 3.365,4.396 3.365,4.396 3.51,4.396 true 4.083,4.833 4.25,4.667 4.25,4.667 4.417,4.667 true 0.115,0.125 1.344,0.323 1.229,0.198 10 false VVT System: 1.927,1.458 3.448,1.667 1.521,0.208 10 false Actual Valve Timing 1.979,2.156 3.406,2.427 1.427,0.271 10 false Target Valve Timing 2.271,2.896 3.073,3.167 0.802,0.271 10 false Correction 0.26,3.74 1.292,3.979 1.031,0.24 10 false Duty-cycle 1.948,4.021 6.396,4.344 4.448,0.323 10 false Cam Timing Oil Control Solenoid Assembly (for Intake Camshaft) 3.552,4.333 6.802,4.583 3.25,0.25 10 false VVT Controller (Camshaft Timing Gear Assembly) 3.26,5.188 6.656,5.563 3.396,0.375 10 false Camshaft Timing Gear Bolt (Intake Camshaft Timing Oil Control Valve) 4.531,4.583 6.5,4.771 1.969,0.188 10 false Intake Camshaft 4.656,0.74 6.802,0.958 2.146,0.219 10 false Camshaft Position Sensor 4.604,1.25 6.344,1.5 1.74,0.25 10 false Crankshaft Position Sensor 4.813,1.76 7.063,2.052 2.25,0.292 10 false Mass Air Flow Meter 4.698,2.292 6.677,2.594 1.979,0.302 10 false Throttle Position Sensor 4.365,3.063 6.865,3.365 2.5,0.302 10 false Engine Coolant Temperature Sensor 4.771,3.573 6.75,3.875 1.979,0.302 10 false Vehicle Speed Sensor 2.438,3.396 3.115,3.729 0.677,0.333 10 false ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P001013 A Camshaft Position Actuator Bank 1 Circuit Open Open or short in cam timing oil control solenoid assembly (for intake camshaft) circuit (1 trip detection logic).
·

Open or short in cam timing oil control solenoid assembly (for intake camshaft) circuit

·

Cam timing oil control solenoid assembly (for intake camshaft)

·

ECM


Comes on DTC stored SAE: P0010

MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the cam timing oil control solenoid assembly (for intake camshaft) circuit. If the cam timing oil control solenoid assembly duty-cycle is excessively high or low while the ignition switch is ON or the engine is running, the ECM will illuminate the MIL and store this DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Wait 5 seconds.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P001013.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A395475E04
1.781,0.76 1.938,0.958 0.156,0.198 10 false 2 1.792,1.385 1.948,1.583 0.156,0.198 10 false 1 4.594,0.74 4.823,0.938 0.229,0.198 10 false 27 4.927,0.75 5.417,0.917 0.49,0.167 10 false OC1+ 4.938,1.406 5.427,1.573 0.49,0.167 10 false OC1- 5.375,2.24 5.865,2.406 0.49,0.167 10 false D51 5.375,2.427 5.865,2.594 0.49,0.167 10 false ECM 0.26,1.813 0.75,1.979 0.49,0.167 10 false D16 0.25,1.979 2.917,2.396 2.667,0.417 10 false Cam Timing Oil Control Solenoid Assembly (for Intake Camshaft) 1.573,1.385 1.729,1.583 0.156,0.198 10 false - 1.573,0.76 1.729,0.958 0.156,0.198 10 false + 4.594,1.375 4.823,1.573 0.229,0.198 10 false 26

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTC after recording the freeze frame data and DTC.

Powertrain > Engine > Clear DTCs
50002 372

Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

2.READ OUTPUT DTC (DTC P001013)
2.READ OUTPUT DTC (DTC P001013)

Pre-procedure1

a.

Start the engine.


Procedure1

b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Post-procedure1

c.

None.


Result:
Result Proceed to
P001013 is output A
DTCs are not output B



A

3.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)

B

3.INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)

OK

4.CHECK HARNESS AND CONNECTOR (CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT) - ECM)

NG

REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)

4.CHECK HARNESS AND CONNECTOR (CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT) - ECM)

Pre-procedure1

a.

Disconnect the cam timing oil control solenoid assembly (for intake camshaft) connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D16-2 (+) - D51-27 (OC1+) Always Below 1 Ω
D16-1 (-) - D51-26 (OC1-) Always Below 1 Ω
D16-2 (+) or D51-27 (OC1+) - Body ground and other terminals Always 10 kΩ or higher
D16-1 (-) or D51-26 (OC1-) - Body ground and other terminals Always 10 kΩ or higher



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR