Refer to the DTC summary for DTC P1C7779.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1C7779
Refer to the description for DTC P1C7779.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1C7779
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P1C8679 | Transmission (Input) Mechanical Linkage Failure | Hybrid vehicle transaxle malfunction (input system lock):
When the vehicle is stopped, an engine cranking signal is sent but the generator (MG1) does not rotate. The generator (MG1) or the engine does not rotate, or the planetary gear unit is malfunctioning. (1 trip detection logic) |
·
Engine ·
Hybrid vehicle transaxle assembly ·
Transmission input damper assembly |
Does not come on | Master Warning: Comes on |
| DTC No. | Data List |
|---|---|
| P1C8679 | ·
Generator Revolution ·
Motor Revolution ·
Engine Speed |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
With the vehicle stopped and the shift lever in P, turn the ignition switch to ON (READY) and gradually depress the accelerator pedal so that the engine starts.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
If this DTC is output, the engine or gears in the transaxle may have seized. Before performing this inspection, check the engine oil, hybrid transaxle fluid, coolant (for Engine) and coolant (for Inverter) levels.
Pre-procedure1
None.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| P1C8679 only is output, or DTCs except the ones in the table below are also output | A |
| Any of the following DTCs including pending DTCs are also output | B |
| Malfunction Content | Relevant DTC | |
|---|---|---|
| Sensor and actuator circuit malfunction | P1C8779 | Generator Mechanical Linkage Failure |
| P1C8879 | Planetary Gear Mechanical Linkage Failure | |
P1C8679 may be output as a result of the malfunction indicated by the DTCs above.
Post-procedure1
Turn the ignition switch off.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1C7779
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1C7779
| Proceed to |
|---|
| NEXT |
NEXT
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1C7779
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1C7779
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1C7779
| Result | Proceed to |
|---|---|
| The absolute value of the difference is less than 500 rpm | A |
| The absolute value of the difference is 500 rpm or more continuously for 1 second | B |
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1C7779
| Proceed to |
|---|
| OK |
| NG |
OK
NG