Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420051 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1CFA12  IGB Signal Circuit Short to Auxiliary Battery  


DESCRIPTION

The hybrid vehicle control ECU monitors the IGB signal received from the certification ECU (smart key ECU assembly). When an error is detected in the IGB signal, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P1CFA12 IGB Signal Circuit Short to Auxiliary Battery An IGB signal from the hybrid vehicle control ECU is on when the ignition switch is off.
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Certification ECU (smart key ECU assembly)


Does not come on Master Warning: Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

4.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A165972E70
0.552,3.052 2.729,3.417 2.177,0.365 10 false Certification ECU (Smart Key ECU Assembly) 1.729,1.542 2.208,1.854 0.479,0.313 10 false IGB 2.083,1.542 2.375,1.854 0.292,0.313 10 false 4 4.99,1.531 5.281,1.781 0.292,0.25 10 false 43 5.24,1.531 5.646,1.802 0.406,0.271 10 false IGB 4.938,3.073 6.677,3.667 1.74,0.594 10 false Hybrid Vehicle Control ECU 4.938,2.896 5.771,3.094 0.833,0.198 10 false H44 0.563,2.885 0.969,3.156 0.406,0.271 10 false H45

CAUTION / NOTICE / HINT

NOTICE:

If the certification ECU (smart key ECU assembly) is replaced, refer to Service Bulletin.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

2.CHECK CONNECTOR CONNECTION CONDITION (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

CONNECT SECURELY

2.CHECK CONNECTOR CONNECTION CONDITION (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Check the connector connection condition of the certification ECU (smart key ECU assembly).

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connector is connected securely and there are no contact problems.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IGB TERMINAL VOLTAGE)

NG

CONNECT SECURELY

3.CHECK HARNESS AND CONNECTOR (IGB TERMINAL VOLTAGE)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

A458550C10
4.698,0.24 5.167,0.521 0.469,0.281 5.771,2.302 5.469,1.635 true 0.271,0.167 0.583,0.323 0.313,0.156 10 false *a 5.771,2.344 6.083,2.5 0.313,0.156 10 false IGB 4.823,0.313 5.135,0.469 0.313,0.156 10 false H44
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
H44-43 (IGB) - Body ground Ignition switch off Below 1 V



Post-procedure1

c.

None.

Result:
Proceed to
OK
NG




OK

NG

4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

Pre-procedure1

a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

A458550C10
4.698,0.24 5.167,0.521 0.469,0.281 5.771,2.302 5.469,1.635 true 0.271,0.167 0.583,0.323 0.313,0.156 10 false *a 5.771,2.344 6.083,2.5 0.313,0.156 10 false IGB 4.823,0.313 5.135,0.469 0.313,0.156 10 false H44
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
H44-43 (IGB) - Body ground Ignition switch off Below 1 V



Post-procedure1

c.

Reconnect the H45 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR