Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420051 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P312387  Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message  


DESCRIPTION

Refer to the description for P0D2D16.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>P0D2D16

The MG ECU, which is built into in the inverter with converter assembly, controls motor (MG2) based on commands from the hybrid vehicle control ECU. The MG ECU monitors communication data and detects malfunctions.

The hybrid vehicle control ECU monitors communication data and detects malfunctions.

A communication error between the MG ECU and the hybrid vehicle control ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message Error in reception from inverter with converter assembly (MG ECU) via serial communication (out of communication standard)
(1 trip detection logic)
·

Wire harness or connector

·

Inverter with converter assembly

·

Hybrid vehicle control ECU

·

PCU FR fuse


Comes on Master Warning: Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

With ignition switch ON and wait for 2 minutes or more.

4.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for the inverter low-voltage circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Inverter Low-voltage Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery



·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.


·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.


·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.INSPECT FUSE (PCU FR)

Pre-procedure1

a.

Remove the PCU FR fuse from the No. 5 relay block assembly.


Procedure1

b.
A459748C01
2.052,0.74 2.625,1.26 true 0.208,0.156 0.521,0.313 0.313,0.156 10 false *1 2.677,1.292 2.99,1.448 0.313,0.156 10 false *2
*1 No. 5 Relay Block Assembly
*2 PCU FR Fuse


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
PCU FR fuse Always Below 1 Ω



Post-procedure1

c.

Install the PCU FR fuse.


Result:
Proceed to
OK
NG



OK

2.CLEAR DTC

NG

10.REPLACE FUSE (PCU FR)
2.CLEAR DTC

NEXT

3.CHECK DIAGNOSIS RELATED INFORMATION AND DTC OUTPUT (HYBRID CONTROL)
3.CHECK DIAGNOSIS RELATED INFORMATION AND DTC OUTPUT (HYBRID CONTROL)

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 2 minutes or more.


Procedure1

b.

Check Diagnosis Related Information.

Powertrain > Hybrid Control > Utility
Tester Display
Diagnosis Related Information
50005 397 56
Result:
Result Proceed to
Diagnosis Related Information P312387 is output A
Diagnosis Related Information P312387 is not output B



Post-procedure1

c.

Turn the ignition switch off.



A

4.CHECK DTC OUTPUT

B

4.CHECK DTC OUTPUT

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
P312387 is output A
P312387 is not output B



Post-procedure1

c.

Turn the ignition switch off.



A

5.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

B

5.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

6.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

6.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>P033500

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

7.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A56 inverter with converter assembly connector.


Procedure1

c.
A365593C78
0.292,0.906 0.667,1.167 0.375,0.26 2.042,0.917 2.604,0.302 true 1.906,0.906 1.906,0.292 true 2.031,1.25 2.719,1.833 true 1.906,1.25 1.917,1.833 true 0.115,0.125 0.427,0.323 0.313,0.198 10 false *a 0.375,0.969 0.833,1.167 0.458,0.198 10 false A56 2.51,0.094 2.823,0.292 0.313,0.198 10 false +B 1.76,0.104 2.219,0.302 0.458,0.198 10 false +B2 2.563,1.865 3.021,2.063 0.458,0.198 10 false GND1 1.823,1.865 2.438,2.063 0.615,0.198 10 false GND2
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A56-24 (GND1) - Body ground Ignition switch off Below 1 Ω
A56-23 (GND2) - Body ground Ignition switch off Below 1 Ω



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A56-6 (+B) - Body ground Ignition switch ON 11 to 14 V
A56-5 (+B2) - Body ground Ignition switch ON 11 to 14 V


NOTICE:

Turning the ignition switch to ON with the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



Post-procedure1

g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the A56 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - HYBRID VEHICLE CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A56 inverter with converter assembly connector.


c.

Disconnect the A68 hybrid vehicle control ECU connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


Procedure1

f.
A459743C01
0.167,1.219 0.604,1.51 0.438,0.292 0.073,3.365 0.51,3.656 0.438,0.292 1.396,1.5 0.729,2.156 true 1.51,1.5 1.792,2.167 true 0.844,3.604 0.594,4.26 true 1.052,3.469 1.656,4.302 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 0.125,2.479 0.438,2.677 0.313,0.198 10 false *b 0.271,1.302 0.729,1.5 0.458,0.198 10 false A56 0.177,3.448 0.635,3.646 0.458,0.198 10 false A68 1.604,2.208 2.219,2.406 0.615,0.198 10 false HMCH 0.542,2.208 1.156,2.406 0.615,0.198 10 false HMCL 1.51,4.302 2.125,4.5 0.615,0.198 10 false HMCL 0.417,4.292 1.031,4.49 0.615,0.198 10 false HMCH
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A68-2 (HMCL) - Body ground Ignition switch ON Below 1 V
A68-13 (HMCH) - Body ground Ignition switch ON Below 1 V


NOTICE:

Turning the ignition switch to ON with the hybrid vehicle control ECU connector and the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A56-19 (HMCL) - A68-2 (HMCL) Ignition switch off Below 1 Ω
A56-20 (HMCH) - A68-13 (HMCH) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A56-19 (HMCL) or A68-2 (HMCL) - Body ground and other terminals Ignition switch off 10 kΩ or higher
A56-20 (HMCH) or A68-13 (HMCH) - Body ground and other terminals Ignition switch off 10 kΩ or higher


HINT:

As there might be an intermittent malfunction, inspect the following items even if the measured resistance is as specified.

Check that each connector between the inverter with converter assembly and hybrid vehicle control ECU is not loose or disconnected.



Post-procedure1

j.

Reconnect the A68 hybrid vehicle control ECU connector.


k.

Reconnect the A56 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

9.CHECK HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HYBRID VEHICLE CONTROL ECU
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A56 inverter with converter assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

A458550C13
2.49,0.26 2.948,0.573 0.458,0.313 3.083,2.333 3.365,1.281 true 3.906,2.323 3.563,1.385 true 0.313,0.24 0.625,0.396 0.313,0.156 10 false *a 2.615,0.365 3.25,0.615 0.635,0.25 10 false A68 2.781,2.354 3.417,2.604 0.635,0.25 10 false HMCL 3.906,2.354 4.542,2.604 0.635,0.25 10 false HMCH
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A68-2 (HMCL) - A68-13 (HMCH) Ignition switch off 110 to 130 Ω



Post-procedure1

d.

Reconnect the A56 inverter with converter assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

10.REPLACE FUSE (PCU FR)

Pre-procedure1

a.
A459748C01
2.052,0.74 2.625,1.26 true 0.208,0.156 0.521,0.313 0.313,0.156 10 false *1 2.677,1.292 2.99,1.448 0.313,0.156 10 false *2
*1 No. 5 Relay Block Assembly
*2 PCU FR Fuse


Replace the PCU FR fuse.


b.

Turn the ignition switch to ON (READY).


Procedure1

c.

Check if there is an open circuit in the PCU FR fuse in the No. 5 relay block assembly.

OK:

There is no open circuit in the PCU FR fuse.


HINT:

If the fuse does not become open again after turning the ignition switch to ON (READY), it can be assumed that the previous fuse failed due to age.



Post-procedure1

d.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

END

NG

11.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - PCU FR FUSE)
11.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - PCU FR FUSE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the PCU FR fuse from the No. 5 relay block assembly.


c.

Disconnect the A56 inverter with converter assembly connector.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

A459996C01
4.156,1.156 4.583,1.438 0.427,0.281 5.688,1.25 5.292,0.521 true 5.771,1.229 6.146,0.51 true 0.365,0.135 0.677,0.292 0.313,0.156 10 false *1 2.594,0.219 2.906,0.375 0.313,0.156 10 false *2 4.542,0.156 4.854,0.313 0.313,0.156 10 false *a 5.042,0.375 5.469,0.708 0.427,0.333 10 false +B2 6.198,0.354 6.625,0.688 0.427,0.333 10 false +B 4.26,1.229 4.625,1.51 0.365,0.281 10 false A56
*1 No. 5 Relay Block Assembly *2 PCU FR Fuse Holder
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
- -


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A56-6 (+B), A56-5 (+B2) or 2 (PCU FR fuse holder) - Body ground and other terminals Ignition switch off 10 kΩ or higher



Post-procedure1

e.

Reconnect the A56 inverter with converter assembly connector.


f.

Install the PCU FR fuse.


Result:
Proceed to
OK
NG



OK

12.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
12.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NEXT

REPLACE FUSE (PCU FR)

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (PCU FR)