MALFUNCTION DESCRIPTION
The hybrid vehicle control ECU detects a VB sensor malfunction.
The cause of this malfunction may be one of the following:
Battery ECU assembly malfunction
Communication (wire harness) malfunction
HV battery malfunction
The battery ECU assembly sends HV battery voltage information to the hybrid vehicle control ECU via serial communication.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0B231C | Hybrid/EV Battery "A" Voltage Sensor Voltage Out of Range | Battery ECU assembly malfunction:
When not boosting, difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is large and difference between "Hybrid/EV Battery Voltage" and "VH-Voltage after Boosting" is large. (1 trip detection logic) |
Battery ECU assembly | Comes on | Master Warning: Comes on |
| DTC No. | Data List |
|---|---|
| P0B231C | ·
Hybrid/EV Battery Voltage ·
VL-Voltage before Boosting ·
VH-Voltage after Boosting ·
Boost Ratio |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON (READY).
With the shift lever in D, depress both the accelerator pedal and brake pedal at the same time to raise the "Hybrid/EV Battery SOC" to a sufficient level.
Move the shift lever to P, check that the engine is stopped and move the shift lever to N.
Set the A/C for maximum cooling.
Leave the vehicle for a few minutes.
After the repair if "VL-Voltage before Boosting" and the "Hybrid/EV Battery Voltage" are approximately the same when the ignition switch is turned to ON (READY) with shift lever in P and the accelerator pedal not depressed, the condition is judged as normal.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Performing the check procedures for a long time with shift lever in N may cause DTC P300000 to be set.
If the battery ECU assembly has been replaced, it is necessary to confirm the voltage of each battery block. With ignition switch ON (READY), shift lever in P, the engine stopped and the HV battery voltage at 178 V or more, check the value of Data List items "Hybrid/EV Battery Voltage", "VL-Voltage before Boosting" and "VH-Voltage after Boosting". When the system is normal, the values of "Hybrid/EV Battery Voltage", "VL-Voltage before Boosting", and "VH-Voltage after Boosting" should be almost equal. If the difference between each value is more than the voltages specified below, the system is malfunctioning.
| Inspection Voltage | Maximum Voltage Difference |
|---|---|
| Difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" | 32 V |
| Difference between "Hybrid/EV Battery Voltage" and "VH-Voltage after Boosting" | 33 V |
| Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" | 56 V |
Pre-procedure1
None.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| P0B231C and Microcomputer malfunction of Hybrid control system DTCs in the table below are output | A |
| P0B231C and Microcomputer malfunction of Motor generator control system DTCs in the table below are output | B |
| P0B231C and Microcomputer malfunction of Hybrid battery system DTCs in the table below are output | C |
| P0B231C and Power source circuit malfunction of Motor generator control system DTCs in the table below are output | D |
| P0B231C and Communication system malfunction of Hybrid control system DTCs in the table below are output | E |
| P0B231C and Sensor and actuator circuit malfunction of Hybrid battery system DTCs in the table below are output | F |
| P0B231C and System malfunction of Motor generator control system DTCs in the table below are output | G |
| P0B231C and DTCs other than the DTCs in the table below are output | H |
| Only P0B231C is output | I |
| Malfunction Content | System | Relevant DTC | |
|---|---|---|---|
| Microcomputer malfunction | Hybrid control system | P0A1B49 | Drive Motor "A" Control Module Internal Electronic Failure |
| P060647 | Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure | ||
| P060B49 | Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure | ||
| P060687 | Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message | ||
| P060A47 | Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure | ||
| P060A87 | Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message | ||
| Motor generator control system | P0A1B1F | Generator Control Module Circuit Intermittent | |
| P0A1A47 | Generator Control Module Watchdog / Safety MC Failure | ||
| P0A1A49 | Generator Control Module Internal Electronic Failure | ||
| P1C2A1C | Generator A/D Converter Circuit Circuit Voltage Out of Range | ||
| P1C2A49 | Generator A/D Converter Circuit Internal Electronic Failure | ||
| P313383 | Communication Error from Generator to Drive Motor "A" Value of Signal Protection Calculation Incorrect | ||
| P313386 | Communication Error from Generator to Drive Motor "A" Signal Invalid | ||
| P313387 | Communication Error from Generator to Drive Motor "A" Missing Message | ||
| Hybrid battery system | P060B49 | Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure | |
| P060687 | Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message | ||
| P060A47 | Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure | ||
| P060A87 | Hybrid/EV Battery Energy Control Module Processor from Monitoring Processor Missing Message | ||
| P0E2D00 | Hybrid/EV Battery Energy Control Module Hybrid/EV Battery Monitor Performance | ||
| Power source circuit malfunction | Motor generator control system | P06D61C | Generator Control Module Offset Power Circuit Voltage Out of Range |
| Communication system malfunction | Hybrid control system | P312387 | Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message |
| U011187 | Lost Communication with Hybrid/EV Battery Energy Control Module "A" Missing Message | ||
| Sensor and actuator circuit malfunction | Hybrid battery system | P301A1C | Hybrid Battery Stack 1 Cell Voltage Detection Voltage Out of Range |
| P1A001C | Hybrid Battery Stack 2 Cell Voltage Detection Voltage Out of Range | ||
| P1AFD1C | Flying Capacitor/Internal Control Module Hybrid/EV Battery Monitor Voltage Out of Range | ||
| System malfunction | Motor generator control system | P0D2D16 | Drive Motor "A" Inverter Voltage Sensor (VH) Circuit Voltage Below Threshold |
| P0D2D17 | Drive Motor "A" Inverter Voltage Sensor (VH) Circuit Voltage Above Threshold | ||
| P0E3116 | DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Below Threshold | ||
| P0E3117 | DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Above Threshold | ||
P0B231C may be output as a result of the malfunction indicated by the DTCs above.
The chart above is listed in inspection order of priority.
Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
Post-procedure1
Turn the ignition switch off.
A
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
B
C
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
D
E
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
F
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
G
H
I