Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › BATTERY ECU
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0424584 BATTERY ECU A

HYBRID / BATTERY CONTROL  BATTERY ECU  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during battery ECU assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of battery ECU assembly Current sensor offset learning DTCs are stored (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



NOTICE:
·

The type of battery ECU assembly to be used varies depending on the vehicle model.

·

The type of battery ECU assembly to be used varies depending on the vehicle model.

·

If the wrong type of battery ECU assembly is installed, the ignition switch cannot be turned on (READY).

·

After installing the battery ECU assembly, perform the following to check that the ignition switch can be turned on (READY).

-

Turn the ignition switch to ON (READY).

-

Turn the ignition switch off and wait for 30 seconds or more.

-

Turn the ignition switch on (READY) again.




HINT:
·

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2. WHEN REPLACING BATTERY ECU ASSEMBLY

HV battery learning values are stored in the battery ECU assembly and ECM and are used to detect malfunctions and illuminate the hybrid battery indicator light in the combination meter assembly. When either of these ECUs is replaced, the new ECU receives the HV battery learning values from the other ECU and stores them.

NOTICE:
·

Do not replace the battery ECU assembly and ECM at the same time as the HV battery learning values will be lost. However, if it is necessary to replace both ECUs at the same time, replace them by following the procedure below.

·

Do not replace the battery ECU assembly or ECM with a used one from another vehicle.



a.

Procedure when replacing both battery ECU assembly and ECM:

i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


ii.

Replace either ECU.


iii.

Connect the cable to the negative (-) auxiliary battery terminal.


iv.

Turn the ignition switch on (READY) and wait for 5 minutes or more.


v.

Turn the ignition switch off and disconnect the cable from the negative (-) auxiliary battery terminal.


vi.

Replace the other ECU.


vii.

Connect the cable to the negative (-) auxiliary battery terminal.


viii.

Check that the ignition switch can be turned on (READY).

HINT:

If the battery ECU assembly and ECM are replaced at the same time without following the above procedure, replace either of the ECUs with its original one and then replace it again by following the above procedure. If the correct procedure is not followed, perform the procedure again from the beginning.




Hide 7.INSTALL CONNECTOR COVER ASSEMBLY

Hide 73350C 9.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 10.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 11.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 76971G 12.REMOVE REAR UNDER COVER

Hide 71033 13.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide G92N1 14.REMOVE HV BATTERY UPPER COVER PANEL

Hide G9290A 15.REMOVE NO.1 HV BATTERY HOSE

Hide 821H1 16.DISCONNECT FLOOR UNDER WIRE

Hide G920NB 18.REMOVE UPPER HV BATTERY COVER SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A464174C01
1.385,0.021 1.604,0.188 0.219,0.167 10 true *a 0.469,0.073 0.677,0.229 0.208,0.156 10 true *b 1.896,0.063 2.115,0.229 0.219,0.167 10 true *a 3.073,1.479 3.292,1.646 0.219,0.167 10 true *a 0.198,1.063 0.417,1.229 0.219,0.167 10 true *a 2.698,2 2.906,2.177 0.208,0.177 10 true *b 1.927,1.927 2.115,2.104 0.188,0.177 10 true *b 1.146,1.885 1.354,2.063 0.208,0.177 10 true *b 0.615,1.719 0.823,1.885 0.208,0.167 10 true *b 2.313,0.177 2.5,0.354 0.188,0.177 10 true *b
*a Bolt
*b Nut


Remove the 4 bolts, 6 nuts and upper HV battery cover sub-assembly from the HV battery.


Hide G929A 19.REMOVE NO. 1 HV BATTERY HOSE

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A464182

Remove the clip and No. 1 HV battery hose from the HV battery.


Hide 89890A 20.REMOVE BATTERY ECU ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A464185

Move the lock lever while pushing the lock on the connector, and disconnect the 3 battery ECU assembly connectors.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



b.
A464186

Remove the 3 nuts and battery ECU assembly from the HV battery.

NOTICE:

If the battery ECU assembly has been struck or dropped, replace it.