MALFUNCTION DESCRIPTION
The hybrid vehicle control ECU detects a VB sensor or VL sensor malfunction.
The cause of this malfunction may be one of the following:
Voltage sensor malfunction
Motor generator control ECU (MG ECU) malfunction
Communication (wire harness) malfunction
HV battery malfunction
No. 1 traction battery device box assembly malfunction
Inverter with converter assembly malfunction
High-voltage wire harness malfunction
High-voltage connector or connection malfunction
Inspection Overview
| Inspection Content | Reason (Narrow Down in Order Using Inspection Procedures Below) | Inspection Step |
|---|---|---|
| Check for DTCs (HV) | Output DTCs | 1 |
| Check for DTCs (check voltage sensor malfunction locations)
Check for DTCs (drive test) |
Ignition switch to ON (READY) (vehicle stopped or being driven) and then check whether DTCs are output again. | 3, 4 |
| Read value using GTS | Data List value | 5 |
| Check freeze frame data (HV) | Freeze Frame Data | 6 |
| Read value using GTS | Accelerator and brake pedal simultaneously depressed Data List value | 7 |
For a description of the boost converter.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL SYSTEM>P0CA300
The MG ECU uses a voltage sensor (VL) that is built into the boost converter to detect the high voltage before it is boosted. The ECU also uses the battery ECU assembly to detect HV battery voltage (VB).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P1C2D62 | Hybrid/EV Battery "A" Voltage Sensor/Boosting Converter Voltage Sensor "A" Signal Compare Failure | Voltages from HV battery voltage (VB) sensor and boost converter voltage (VL) sensor deviate:
Difference between "VL-Voltage before Boosting" and "Hybrid/EV Battery Voltage" is large when the boosting request is given. (1 trip detection logic) |
·
Inverter with converter assembly ·
Battery ECU assembly |
Comes on | Master Warning: Comes on |
| DTC No. | Data List |
|---|---|
| P1C2D62 | ·
Hybrid/EV Battery Voltage ·
VL-Voltage before Boosting ·
VH-Voltage after Boosting ·
Boost Ratio |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON (READY).
With the shift lever in D, depress both the accelerator pedal and brake pedal at the same time to raise the "Hybrid/EV Battery SOC" to a sufficient level.
Move the shift lever to P, check that the engine is stopped and move the shift lever to N.
Set the A/C for maximum cooling.
Leave the vehicle for a few minutes.
When the accelerator pedal is not depressed with the ignition switch ON (READY) and shift lever in P, if "VL-Voltage before Boosting" and the "Hybrid/EV Battery Voltage" is approximately the same after repair, the condition is judged as normal.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Pre-procedure1
None.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| P1C2D62 and Microcomputer malfunction of Hybrid control system DTCs in the table below are output | A |
| P1C2D62 and Microcomputer malfunction of Motor generator control system DTCs in the table below are output | B |
| P1C2D62 and Microcomputer malfunction of Hybrid battery system DTCs in the table below are output | C |
| P1C2D62 and Power source circuit malfunction of Motor generator control system DTCs in the table below are output | D |
| P1C2D62 and Communication system malfunction of Hybrid control system DTCs in the table below are output | E |
| P1C2D62 and Sensor and actuator circuit malfunction of Hybrid battery system DTCs in the table below are output | F |
| P1C2D62 and System malfunction of Motor generator control system DTCs in the table below are output | G |
| P0E311C, P0CA300 or P0B231C is output and DTCs other than the DTCs in the table below are output | H |
| P1C2D62,P0E311C and P0CA300 are output | I |
| P1C2D62 and P0B231 are output | J |
| Only P1C2D62 is output | K |
| Malfunction Content | System | Relevant DTC | |
|---|---|---|---|
| Microcomputer malfunction | Hybrid control system | P060647 | Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure |
| P0A1B49 | Drive Motor "A" Control Module Internal Electronic Failure | ||
| P060B49 | Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure | ||
| P060687 | Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message | ||
| P060A47 | Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure | ||
| P060A87 | Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message | ||
| Motor generator control system | P0A1A47 | Generator Control Module Watchdog / Safety MC Failure | |
| P0A1A49 | Generator Control Module Internal Electronic Failure | ||
| P0A1B1F | Generator Control Module Circuit Intermittent | ||
| P1C2A1C | Generator A/D Converter Circuit Circuit Voltage Out of Range | ||
| P1C2A49 | Generator A/D Converter Circuit Internal Electronic Failure | ||
| P313383 | Communication Error from Generator to Drive Motor "A" Value of Signal Protection Calculation Incorrect | ||
| P313386 | Communication Error from Generator to Drive Motor "A" Signal Invalid | ||
| P313387 | Communication Error from Generator to Drive Motor "A" Missing Message | ||
| Hybrid battery system | P060B49 | Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure | |
| P060687 | Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message | ||
| P060A47 | Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure | ||
| P060A87 | Hybrid/EV Battery Energy Control Module Processor from Monitoring Processor Missing Message | ||
| P0E2D00 | Hybrid/EV Battery Energy Control Module Hybrid/EV Battery Monitor Performance | ||
| Power source circuit malfunction | Motor generator control system | P06D61C | Generator Control Module Offset Power Circuit Voltage Out of Range |
| Communication system malfunction | Hybrid control system | P312387 | Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message |
| U011187 | Lost Communication with Hybrid/EV Battery Energy Control Module "A" Missing Message | ||
| Sensor and actuator circuit malfunction | Hybrid battery system | P301A1C | Hybrid Battery Stack 1 Cell Voltage Detection Voltage Out of Range |
| P1A001C | Hybrid Battery Stack 2 Cell Voltage Detection Voltage Out of Range | ||
| P1AFD1C | Flying Capacitor/Internal Control Module Hybrid/EV Battery Monitor Voltage Out of Range | ||
| System malfunction | Motor generator control system | P0E3116 | DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Below Threshold |
| P0E3117 | DC/DC Converter Voltage Sensor "A" (VL) Circuit Voltage Above Threshold | ||
P1C2D62 may be output as a result of the malfunction indicated by the DTCs above.
The chart above is listed in inspection order of priority.
Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
Post-procedure1
Turn the ignition switch off.
A
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
B
C
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
D
E
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
F
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
G
H
I
J
K
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P06881F
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Apply the parking brake and secure the wheels using chocks.
Perform this test with the AUTO function (shift-linked function) of the electronic parking brake system off.
When the parking brake indicator (red) is illuminated after the electric parking brake switch (electric parking brake switch assembly) has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch (electric parking brake switch assembly) is pulled to the lock side one more time.
Turn the ignition switch to ON (READY). *1
If the value of "Hybrid/EV Battery SOC" is less than 55%, move the shift lever to D and charge the HV battery by depressing the accelerator pedal and brake pedal simultaneously until the value reaches 55% or more. *2
| Tester Display |
|---|
| Hybrid/EV Battery SOC |
| Hybrid/EV Battery Current |
Move the shift lever to P. *3
Set the air conditioning to MAX COOL and turn the headlights on. *4
Confirm that "Hybrid/EV Battery Current" is more than 3 A. *5
With the engine stopped and the conditions of steps *3, *4 and *5 satisfied, leave the vehicle for 15 seconds. *6
Procedure1
Check for DTCs. *7
If the low HV battery information comes on, move the shift lever to P and start the engine to charge the HV battery. After the engine stops, perform steps *1 through *7 again.
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| No DTCs in the table below are output | B |
| P0E311C or P0CA300 is output | C |
| P0B231C or P1C8349 is output | D |
| P300000 is output | E |
| Malfunction Content | System | Relevant DTC | |
|---|---|---|---|
| Sensor and actuator circuit malfunction | Hybrid control system | P0E311C | Boosting Converter Voltage Sensor "A" Voltage Out of Range |
| P0B231C | Hybrid/EV Battery "A" Voltage Sensor Voltage Out of Range | ||
| System malfunction | Hybrid control system | P1C8349 | High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction |
| Motor generator control system | P0CA300 | DC/DC Converter Step Up Voltage Performance | |
| Hybrid battery system | P300000 | Hybrid/EV Battery Discharge Control Malfunction | |
Post-procedure1
Turn the ignition switch off.
A
B
C
D
E
Pre-procedure1
Turn the ignition switch to ON (READY). *8
Perform a road test that repeats full acceleration to 60 km/h (37 mph) and then braking to a complete stop three times. *9
Perform this road test only in an appropriate safe location, in accordance with all local laws.
This road test is performed to drive the car under high load and cause a change in the HV battery voltage.
Procedure1
Check for DTCs. *10
| Result | Proceed to |
|---|---|
| DTCs are output | A |
| No DTCs in the table below are output | B |
| P0E311C or P0CA300 is output | C |
| P0B231C or P1C8349 is output | D |
| P300000 is output | E |
| Malfunction Content | System | Relevant DTC | |
|---|---|---|---|
| Sensor and actuator circuit malfunction | Hybrid control system | P0E311C | Boosting Converter Voltage Sensor "A" Voltage Out of Range |
| P0B231C | Hybrid/EV Battery "A" Voltage Sensor Voltage Out of Range | ||
| System malfunction | Hybrid control system | P1C8349 | High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction |
| Motor generator control system | P0CA300 | DC/DC Converter Step Up Voltage Performance | |
| Hybrid battery system | P300000 | Hybrid/EV Battery Discharge Control Malfunction | |
Post-procedure1
Turn the ignition switch off.
A
B
C
D
E
Pre-procedure1
Apply the parking brake and secure the wheels using chocks.
Perform this test with the AUTO function (shift-linked function) of the electronic parking brake system off.
When the parking brake indicator (red) is illuminated after the electric parking brake switch (electric parking brake switch assembly) has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch (electric parking brake switch assembly) is pulled to the lock side one more time.
Turn the ignition switch to ON (READY).
Procedure1
If the value of "Hybrid/EV Battery SOC" is less than 55%, move the shift lever to D and charge the HV battery by depressing the accelerator pedal and brake pedal simultaneously until the value reaches 55% or more.
| Tester Display |
|---|
| VL-Voltage before Boosting |
| VH-Voltage after Boosting |
| Hybrid/EV Battery SOC |
| Hybrid/EV Battery Voltage |
Release the accelerator pedal, move the shift lever to P and wait for the engine to stop. Read the Data List when the engine stops.
If the engine starts, wait until it stops before continuing.
| Result | Proceed to |
|---|---|
| Both of the following are not satisfied. | A |
| Both of the following are satisfied:
·
Difference between "Hybrid/EV Battery Voltage" and "VH-Voltage after Boosting" is less than 5 V. ·
Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" is more than 30 V. |
B |
| Both of the following are satisfied:
·
Difference between "VH-Voltage after Boosting" and "VL-Voltage before Boosting" is less than 5 V. ·
Difference between "Hybrid/EV Battery Voltage" and "VH-Voltage after Boosting" is more than 15 V. |
C |
Post-procedure1
Turn the ignition switch off.
A
B
C
Pre-procedure1
None.
Procedure1
Read the freeze frame data of DTC P1C2D62.
| Tester Display |
|---|
| VL-Voltage before Boosting |
| Hybrid/EV Battery Voltage |
| Result | Proceed to |
|---|---|
| Both of the following are satisfied or both of the following are not satisfied. | A |
| "VL-Voltage before Boosting" is less than 129 V or more than 201 V. | B |
| "Hybrid/EV Battery Voltage" is less than 129 V or more than 201 V. | C |
Post-procedure1
Turn the ignition switch off.
A
B
C
Pre-procedure1
Apply the parking brake and secure the wheels using chocks.
Perform this test with the AUTO function (shift-linked function) of the electronic parking brake system off.
When the parking brake indicator (red) is illuminated after the electric parking brake switch (electric parking brake switch assembly) has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch (electric parking brake switch assembly) is pulled to the lock side one more time.
Turn the ignition switch to ON (READY).
Procedure1
If the value of "Hybrid/EV Battery SOC" is less than 55%, move the shift lever to D and charge the HV battery by depressing the accelerator pedal and brake pedal simultaneously until the value reaches 55% or more.
| Tester Display |
|---|
| Hybrid/EV Battery SOC |
| Hybrid/EV Battery Voltage |
| Hybrid/EV Battery Cell 1 Voltage |
| Hybrid/EV Battery Cell 2 Voltage |
| Hybrid/EV Battery Cell 3 Voltage |
| Hybrid/EV Battery Cell 4 Voltage |
| Hybrid/EV Battery Cell 5 Voltage |
| Hybrid/EV Battery Cell 6 Voltage |
| Hybrid/EV Battery Cell 7 Voltage |
| Hybrid/EV Battery Cell 8 Voltage |
| Hybrid/EV Battery Cell 9 Voltage |
| Hybrid/EV Battery Cell 10 Voltage |
| Hybrid/EV Battery Cell 11 Voltage |
| Hybrid/EV Battery Cell 12 Voltage |
| Hybrid/EV Battery Cell 13 Voltage |
| Hybrid/EV Battery Cell 14 Voltage |
| Hybrid/EV Battery Cell 15 Voltage |
| Hybrid/EV Battery Cell 16 Voltage |
| Hybrid/EV Battery Cell 17 Voltage |
| Hybrid/EV Battery Cell 18 Voltage |
| Hybrid/EV Battery Cell 19 Voltage |
| Hybrid/EV Battery Cell 20 Voltage |
| Hybrid/EV Battery Cell 21 Voltage |
| Hybrid/EV Battery Cell 22 Voltage |
| Hybrid/EV Battery Cell 23 Voltage |
| Hybrid/EV Battery Cell 24 Voltage |
| Hybrid/EV Battery Cell 25 Voltage |
| Hybrid/EV Battery Cell 26 Voltage |
| Hybrid/EV Battery Cell 27 Voltage |
| Hybrid/EV Battery Cell 28 Voltage |
| Hybrid/EV Battery Cell 29 Voltage |
| Hybrid/EV Battery Cell 30 Voltage |
| Hybrid/EV Battery Cell 31 Voltage |
| Hybrid/EV Battery Cell 32 Voltage |
| Hybrid/EV Battery Cell 33 Voltage |
| Hybrid/EV Battery Cell 34 Voltage |
| Hybrid/EV Battery Cell 35 Voltage |
| Hybrid/EV Battery Cell 36 Voltage |
| Hybrid/EV Battery Cell 37 Voltage |
| Hybrid/EV Battery Cell 38 Voltage |
| Hybrid/EV Battery Cell 39 Voltage |
| Hybrid/EV Battery Cell 40 Voltage |
| Hybrid/EV Battery Cell 41 Voltage |
| Hybrid/EV Battery Cell 42 Voltage |
| Hybrid/EV Battery Cell 43 Voltage |
| Hybrid/EV Battery Cell 44 Voltage |
| Hybrid/EV Battery Cell 45 Voltage |
| Hybrid/EV Battery Cell 46 Voltage |
| Hybrid/EV Battery Cell 47 Voltage |
| Hybrid/EV Battery Cell 48 Voltage |
Release the accelerator pedal, move the shift lever to P and wait for the engine to stop. Read the Data List when the engine stops.
If the engine starts, wait until it stops before continuing.
| Result | Proceed to |
|---|---|
| Both of the following are satisfied:
·
Sum of all "Hybrid/EV Battery Cell 1 to 48 Voltage" is more than ("Hybrid/EV Battery Voltage" - 10 V) ·
Sum of all "Hybrid/EV Battery Cell 1 to 48 Voltage" is less than ("Hybrid/EV Battery Voltage" + 10 V) |
A |
| The preceding condition is not satisfied. | B |
Post-procedure1
Turn the ignition switch off.
A
B