Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420051 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Drive Mode Select Switch Circuit  


DESCRIPTION

When the drive mode switch (combination switch assembly) is operated, a switch signal is sent to the hybrid vehicle control ECU and the hybrid vehicle control ECU changes the drive mode.

HINT:
·

If the ignition switch is turned off while in POWER mode, the drive mode will automatically be changed to NORMAL mode when the ignition switch is turned to ON.

·

If the ignition switch is turned off while in NORMAL mode or ECO mode, the selected drive mode will resume when the ignition switch is turned to ON.



WIRING DIAGRAM

C280820E49
4.688,2.729 5.146,2.927 0.458,0.198 10 false H44 4.688,2.875 6.552,3.302 1.865,0.427 10 false Hybrid Vehicle Control ECU 5.094,2.042 5.708,2.24 0.615,0.198 10 false PDRV 4.823,2.031 5.104,2.344 0.281,0.313 10 false 37 1.344,2.781 1.802,2.979 0.458,0.198 10 false H18 1.333,2.927 4.458,3.26 3.125,0.333 10 false Drive Mode Switch (Combination Switch Assembly) 3.198,2.063 3.417,2.333 0.219,0.271 10 false 8 2.802,2.063 3.167,2.313 0.365,0.25 10 false DRV 1.771,2.063 2.229,2.26 0.458,0.198 10 false E 1.583,2.052 1.75,2.302 0.167,0.25 10 false 5 1.646,1.219 3.563,1.427 1.917,0.208 10 false Combination Meter Assembly 5.75,1.708 6.063,1.906 0.313,0.198 10 false +B 0.563,3.375 2.479,3.625 1.917,0.25 10 false : CAN Communication Line

PROCEDURE

1.READ VALUE USING GTS (CAN BUS CHECK)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Pattern Select Switch EV Mode Circuit

Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed B



A

2.CHECK DTC OUTPUT (HEALTH CHECK)

B

2.CHECK DTC OUTPUT (HEALTH CHECK)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>Pattern Select Switch EV Mode Circuit

Result:
Result Proceed to
No DTCs are output A
DTCs are output B



A

3.CHECK DRIVE MODE STATUS (NORMAL MODE, ECO MODE, POWER MODE)

B

GO TO DTC CHART

3.CHECK DRIVE MODE STATUS (NORMAL MODE, ECO MODE, POWER MODE)
a.

Turn the ignition switch to ON.


b.

Operate the drive mode switch (combination switch assembly) to change the drive mode.


c.

Check that the drive mode indicator is displayed on the multi-information display and changes according to the selected drive mode.

Result:
Result Proceed to
The display changes according to the drive mode switch (combination switch assembly) operation. A
The display does not change according to the drive mode select switch (combination switch assembly) operation. B



d.

Turn the ignition switch off.



A

B

4.READ VALUE USING GTS (POWERTRAIN DRIVE MODE SWITCH)
4.READ VALUE USING GTS (POWERTRAIN DRIVE MODE SWITCH)
a.

Read the value displayed on the GTS.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition
Powertrain Drive Mode Switch Drive mode switch (combination switch assembly) condition ON or OFF Drive mode sswitch (combination switch assembly) not operated: OFF
Drive mode switch (combination switch assembly) being pushed and held: ON
Powertrain > Hybrid Control > Data List
Tester Display
Powertrain Drive Mode Switch
50003 397 324
Result:
Result Proceed to
The display changes according to the drive mode switch (combination switch assembly) operation. A
The display does not change according to the drive mode switch (combination switch assembly) operation. B



b.

Turn the ignition switch off.



A

B

5.INSPECT DRIVE MODE SWITCH (COMBINATION SWITCH ASSEMBLY)
5.INSPECT DRIVE MODE SWITCH (COMBINATION SWITCH ASSEMBLY)

OK

6.CHECK HARNESS AND CONNECTOR (DRIVE MODE SWITCH (COMBINATION SWITCH ASSEMBLY) - BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (DRIVE MODE SWITCH (COMBINATION SWITCH ASSEMBLY) - BODY GROUND)
a.

Disconnect the H18 drive mode switch (combination switch assembly) connector.


b.
A368640C12
0.417,1 0.844,1.302 0.427,0.302 1.104,1.823 1.375,1.5 true 0.188,0.198 0.5,0.354 0.313,0.156 10 false *a 0.521,1.083 0.833,1.24 0.313,0.156 10 false H18 1.021,1.865 1.188,2.042 0.167,0.177 10 false E
*a Front view of wire harness connector
(to Drive Mode Switch (Combination Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H18-5 (E) - Body ground Always Below 1 Ω



c.

Reconnect the H18 drive mode switch (combination switch assembly) connector.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - DRIVE MODE SWITCH (COMBINATION SWITCH ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - DRIVE MODE SWITCH (COMBINATION SWITCH ASSEMBLY))
a.

Disconnect the H44 hybrid vehicle control ECU connector.


b.

Disconnect the H18 drive mode switch (combination switch assembly) connector.


c.
A368646C35
1.625,0.219 2.115,0.51 0.49,0.292 1.49,2.542 1.979,2.833 0.49,0.292 2.563,2.115 2.271,1.552 true 2.333,4.219 2.094,3.771 true 0.302,0.177 0.615,0.333 0.313,0.156 10 false *a 0.333,2.76 0.646,2.917 0.313,0.156 10 false *b 1.635,2.625 1.948,2.781 0.313,0.156 10 false H18 1.771,0.302 2.083,0.458 0.313,0.156 10 false H44 2.563,2.177 3.115,2.406 0.552,0.229 10 false PDRV 2.365,4.24 2.729,4.438 0.365,0.198 10 false DRV
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Drive Mode Switch (Combination Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H44-37 (PDRV) - H18-8 (DRV) Always Below 1 Ω
H44-37 (PDRV) or H18-8 (DRV) - Body ground Always 10 kΩ or higher



d.

Reconnect the H18 drive mode switch (combination switch assembly) connector.


e.

Reconnect the H44 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR