Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420051 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  U011187  Lost Communication with Hybrid/EV Battery Energy Control Module "A" Missing Message  


DESCRIPTION

The hybrid vehicle control ECU transmits and receives signals via CAN communication to and from the battery ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
U011187 Lost Communication with Hybrid/EV Battery Energy Control Module "A" Missing Message The hybrid vehicle control ECU cannot receive signals from the battery ECU assembly
(1 trip detection logic)
·

Battery ECU assembly

·

Hybrid vehicle control ECU

·

Wire harness or connector


Comes on Master Warning:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 2 minutes or more.

4.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A460068E02
2.01,3.917 4.073,4.208 2.063,0.292 10 false Hybrid Vehicle Control ECU 5.521,4.208 7.031,4.448 1.51,0.24 10 false Battery ECU Assembly 0.521,4.573 2.313,4.854 1.792,0.281 10 false Auxiliary Battery 0.719,5.385 2.49,5.594 1.771,0.208 10 false : CAN Communication Line 3.885,2.115 4.698,2.313 0.813,0.198 10 false IGCT-MAIN 4.823,1.281 5.781,1.51 0.958,0.229 10 false IGCT NO.2 1.271,3.438 2.229,3.667 0.958,0.229 10 false IGCT-MAIN 2.719,1.823 3.177,2.01 0.458,0.188 10 false MREL 2.75,2.646 3.188,2.844 0.438,0.198 10 false CA4H 2.76,3.115 3.198,3.292 0.438,0.177 10 false CA4L 5.958,3.104 6.917,3.333 0.958,0.229 10 false CA1L 5.958,2.729 6.917,2.958 0.958,0.229 10 false CA1H 5.969,1.125 6.927,1.354 0.958,0.229 10 false IGCT 3.792,1.729 3.938,1.927 0.146,0.198 10 false 1 4.469,1.708 4.667,1.896 0.198,0.188 10 false 2 3.781,1.021 3.917,1.229 0.135,0.208 10 false 3 4.479,1.021 4.615,1.219 0.135,0.198 10 false 5 5.219,1 5.396,1.177 0.177,0.177 10 false 2 4.917,1 5.063,1.188 0.146,0.188 10 false 1 5.698,1 5.938,1.188 0.24,0.188 10 false 24 3.229,1.708 3.469,1.906 0.24,0.198 10 false 47 5.667,2.458 5.875,2.646 0.208,0.188 10 false 36 5.667,2.927 5.896,3.115 0.229,0.188 10 false 35 5.969,0.583 6.927,0.813 0.958,0.229 10 false AM 5.708,0.479 5.958,0.656 0.25,0.177 10 false 12 4.802,0.75 5.76,0.979 0.958,0.229 10 false ECU-B NO.1 1.021,0.75 2.146,0.958 1.125,0.208 10 false INP STD NO.1-3 1.271,0.469 1.438,0.667 0.167,0.198 10 false 1 1.573,0.458 1.781,0.656 0.208,0.198 10 false 2 5.958,3.552 6.917,3.781 0.958,0.229 10 false GND 0.385,3.396 1.167,3.594 0.781,0.198 10 false BATT-MAIN 5.198,0.458 5.375,0.635 0.177,0.177 10 false 2 4.906,0.469 5.052,0.656 0.146,0.188 10 false 1 3.24,2.448 3.479,2.646 0.24,0.198 10 false 10 3.229,2.948 3.469,3.146 0.24,0.198 10 false 23 5.656,3.406 5.885,3.594 0.229,0.188 10 false 34 5.521,4.042 5.823,4.229 0.302,0.188 10 false z12 2.021,3.76 2.323,3.948 0.302,0.188 10 false H44

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C44
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

·

As interlock circuit DTCs or other DTCs may be stored when the ignition switch is turned to ON in the following procedure, make sure to clear the DTCs after inspection.



PROCEDURE

1.CHECK DTC OUTPUT (HV BATTERY)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

c.

Turn the ignition switch off.



A

2.CHECK BATTERY ECU ASSEMBLY (IGCT VOLTAGE)

B

2.CHECK BATTERY ECU ASSEMBLY (IGCT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Disconnect the z12 battery ECU assembly connector

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




Procedure1

e.
A459571C10
1.49,0.115 1.948,0.427 0.458,0.313 1.677,2.875 2.073,2.219 true 2.781,0.656 2.688,0.656 2.688,0.656 2.281,1.958 true 2.188,2.875 2.292,2.094 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.615,0.198 2.073,0.396 0.458,0.198 10 false z12 2.833,0.604 3.302,0.833 0.469,0.229 10 false AM 1.552,2.917 1.99,3.115 0.438,0.198 10 false GND 2.063,2.917 2.531,3.146 0.469,0.229 10 false IGCT
*a Front view of wire harness connector
(Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z12-12 (AM) - z12-34 (GND) Ignition switch off 11 to 14 V
z12-24 (IGCT) - z12-34 (GND) Ignition switch ON 11 to 14 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



HINT:

As there might be an intermittent malfunction in the battery ECU assembly power source circuit, inspect the following even if the measured voltage is as specified:

·

Installation condition of fuse(s) (before removing fuse(s)) (IGCT circuit)

·

Fuse condition (before and after removing fuse(s)) (IGCT circuit)

·

Connection condition of connectors (IGCT circuit)

·

Wire harness condition (IGCT circuit)

·

Wire harness condition (GND circuit)




Post-procedure1

f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) auxiliary battery terminal.


h.

Install the No. 1 HV battery hose.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY ECU ASSEMBLY POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY ECU ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the H44 hybrid vehicle control ECU connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check that each connector between the hybrid vehicle control ECU and battery ECU assembly is not loose or disconnected.




c.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



d.
A458604N04
0.938,0.229 1.313,0.448 0.375,0.219 1.031,0.26 1.302,0.427 0.271,0.167 10 true z12

Disconnect the z12 battery ECU assembly connector.

NOTICE:
·

Before disconnecting the connector, check that it is not loose or disconnected.

·

Check the terminals of the connector for deformation and corrosion.




Procedure1

e.

Measure the resistance according to the value(s) in the table below.

A459864C02
4.927,0.438 5.354,0.75 0.427,0.313 1.688,0.125 2.115,0.438 0.427,0.313 2.688,2.344 2.385,1.802 true 2.031,2.313 2.302,1.802 true 6.125,2.26 5.688,1.438 true 5.156,2.26 5.552,1.573 true 0.813,0.26 1.125,0.458 0.313,0.198 10 false *a 3.833,0.26 4.146,0.458 0.313,0.198 10 false *b 1.813,0.219 2.271,0.417 0.458,0.198 10 false z12 5.042,0.521 5.5,0.719 0.458,0.198 10 false H44 1.875,2.385 2.333,2.583 0.458,0.198 10 false CA1L 2.542,2.396 3,2.594 0.458,0.198 10 false CA1H 5.99,2.313 6.448,2.51 0.458,0.198 10 false CA4H 4.979,2.302 5.438,2.5 0.458,0.198 10 false CA4L
*a Front view of wire harness connector
(to Battery ECU Assembly)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
z12-36 (CA1H) - H44-10 (CA4H) Ignition switch off Below 1 Ω
z12-35 (CA1L) - H44-23 (CA4L) Ignition switch off Below 1 Ω
H44-10 (CA4H) - Other terminals and body ground Ignition switch off 10 kΩ or higher
H44-23 (CA4L) - Other terminals and body ground Ignition switch off 10 kΩ or higher


NOTICE:

Make sure that each connector between the battery ECU assembly and hybrid vehicle control ECU assembly is not loose or disconnected and its terminals are not deformed or corroded.



f.

Connect the cable to the negative (-) auxiliary battery terminal.


g.

Turn the ignition switch to ON.


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z12-36 (CA1H) - Body ground Ignition switch ON Below 1 V
z12-35 (CA1L) - Body ground Ignition switch ON Below 1 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




Post-procedure1

i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Reconnect the z12 battery ECU assembly connector.


l.

Install the No. 1 HV battery hose.


m.

Reconnect the H44 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HYBRID VEHICLE CONTROL ECU
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.


c.
A458604N04
0.938,0.229 1.313,0.448 0.375,0.219 1.031,0.26 1.302,0.427 0.271,0.167 10 true z12

Disconnect the z12 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


Procedure1

f.
A459571C07
1.49,0.115 1.948,0.427 0.458,0.313 1.677,2.875 2.073,2.219 true 2.719,2.875 2.302,2.208 true 2.188,2.875 2.177,2.219 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.615,0.198 2.073,0.396 0.458,0.198 10 false z12 2.615,2.917 3.083,3.146 0.469,0.229 10 false CA1H 1.552,2.917 1.99,3.115 0.438,0.198 10 false GND 2.063,2.917 2.531,3.146 0.469,0.229 10 false CA1L
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z12-36 (CA1H) - z12-34 (GND) Ignition switch ON 2.5 to 3.5 V
z12-35 (CA1L) - z12-34 (GND) Ignition switch ON 1.5 to 2.5 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z12-36 (CA1H) - z12-35 (CA1L) Ignition switch off 108 to 132 Ω



Post-procedure1

j.

Reconnect the z12 battery ECU assembly connector.


k.

Install the No. 1 HV battery hose.


Result:
Proceed to
OK
NG



OK

NG