Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420053 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P056014  System Voltage (BATT) Circuit Short to Ground or Open  


DESCRIPTION

Auxiliary battery power is supplied to the AM terminal of the battery ECU assembly in order to store DTCs and freeze frame data. Even if the ignition switch is turned off, back-up power is supplied.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P056014 System Voltage (BATT) Circuit Short to Ground or Open Malfunction in the battery ECU assembly back-up power source circuit
(1 trip detection logic)
·

Wire harness or connector

·

Battery ECU assembly

·

Fuse


Comes on Master Warning:
Comes on

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON and wait for 5 seconds or more.

4.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A378946E15
5.229,2.875 6.844,3.438 1.615,0.563 10 false Battery ECU Assembly 4.938,2.875 5.406,3.302 0.469,0.427 10 false z12 5.688,1.125 6.135,1.573 0.448,0.448 10 false AM 5.667,1.708 6.115,2.156 0.448,0.448 10 false GND 5.406,1.021 5.854,1.469 0.448,0.448 10 false 12 5.406,1.604 5.854,2.052 0.448,0.448 10 false 34 3.594,1.313 4.802,1.917 1.208,0.604 10 false ECU-B NO. 1 1.125,1.292 2.063,1.854 0.938,0.563 10 false BATT-MAIN 0.948,2.135 1.885,2.698 0.938,0.563 10 false Auxiliary 2.438,1 3.375,1.563 0.938,0.563 10 false 1 2.646,1 3.583,1.563 0.938,0.563 10 false 2 2.073,1.302 3.323,1.656 1.25,0.354 10 false INP STD NO. 1-3 0.948,2.323 1.885,2.885 0.938,0.563 10 false Battery

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK FUSE (ECU-B NO. 1)

Pre-procedure1

a.
A459947C01
2.177,1.5 2.396,0.813 false 0.135,0.115 0.552,0.573 0.417,0.458 10 false *1 2.385,0.583 2.813,1.146 0.427,0.563 10 false *2
*1 Power Distribution Box Assembly
*2 ECU-B NO. 1 Fuse


Remove the ECU-B NO. 1 fuse from the power distribution box assembly.


Procedure1

b.

Check if there is an open circuit in the ECU-B NO. 1 fuse in the power distribution box assembly.

OK:

There is no open circuit in the ECU-B NO. 1 fuse.



Post-procedure1

c.

Install the ECU-B NO. 1 fuse.


Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY)

NG

REPLACE FUSE (ECU-B NO. 1)

2.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



Procedure1

c.
A458604N01
0.938,0.229 1.313,0.448 0.375,0.219 0.979,0.24 1.281,0.417 0.302,0.177 10 true z12

Check the connector connections and contact pressure of the relevant terminals for the battery ECU assembly.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connectors are connected securely and there are no contact pressure problems.



Post-procedure1

d.

Install the No. 1 HV battery hose.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AM VOLTAGE)

NG

CONNECT SECURELY

3.CHECK HARNESS AND CONNECTOR (AM VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



c.
A458604N01
0.938,0.229 1.313,0.448 0.375,0.219 0.979,0.24 1.281,0.417 0.302,0.177 10 true z12

Disconnect the z12 battery ECU assembly connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


Procedure1

e.
A459571C01
1.49,0.115 1.948,0.427 0.458,0.313 1.729,2.844 2.073,2.219 true 2.583,2.875 2.281,2 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.615,0.198 2.073,0.396 0.458,0.198 10 false z12 2.521,2.917 2.833,3.115 0.313,0.198 10 false AM 1.583,2.917 2.021,3.115 0.438,0.198 10 false GND
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z12-12 (AM) - z12-34 (GND) Ignition switch off 11 to 14 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.



HINT:

As there might be an intermittent malfunction in the battery ECU assembly power source circuit, inspect the following even if the measured voltage is as specified.

·

Installation condition of fuse(s) (before removing fuse(s)) (Power Source Circuit)

·

Fuse condition (before and after removing fuse(s)) (Power Source Circuit)

·

Connection condition of connectors (Power Source Circuit)

·

Wire harness condition (Power Source Circuit)

·

Wire harness condition (GND circuit)




Post-procedure1

f.

Disconnect the cable from the negative (-) auxiliary battery terminal.


g.

Reconnect the z12 battery ECU assembly connector.


h.

Install the No. 1 HV battery hose.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY ECU ASSEMBLY POWER SOURCE CIRCUIT)