Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420053 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0A8196  Hybrid/EV Battery Cooling Fan 1 Component Internal Failure  P0A8198  Hybrid/EV Battery Cooling Fan 1 Component or System Over Temperature  


DESCRIPTION

Refer to the description for DTC P0A8111.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A8111

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A8196 Hybrid/EV Battery Cooling Fan 1 Component Internal Failure The battery cooling blower assembly is malfunctioning and the actual speed is not within the specified range of the target speed calculated by the ECU.*
*: This DTC is not stored when "Hybrid/EV Battery Cooling Fan 1 Frequency" is excessively low or high.
(2 trip detection logic)
·

Wire harness or connector

·

Battery cooling blower assembly

·

Battery ECU assembly

·

No. 1 HV battery intake filter

·

No. 1 hybrid battery intake duct


Comes on Master Warning:
Comes on
P0A8198 Hybrid/EV Battery Cooling Fan 1 Component or System Over Temperature The HV battery temperature is high and the battery cooling blower assembly is malfunctioning and the actual speed is not within the specified range of the target speed calculated by the ECU.*
*: This DTC is not stored when "Hybrid/EV Battery Cooling Fan 1 Frequency" is excessively low or high.
(1 trip detection logic)
·

Wire harness or connector

·

Battery cooling blower assembly

·

Battery ECU assembly

·

No. 1 HV battery intake filter

·

No. 1 hybrid battery intake duct


Comes on Master Warning:
Comes on

Related Data List
DTC No. Data List
P0A8196
·

Hybrid/EV Battery Cooling Fan 1 Drive Request

·

Hybrid/EV Battery Cooling Fan 1 Drive Status

·

Hybrid/EV Battery Cooling Fan 1 Frequency


P0A8198

The following items can be helpful when performing repairs:

Data List
·

Hybrid/EV Battery Temperature 1 to 6

·

BATT Voltage


HINT:

"Hybrid/EV Battery Cooling Fan 1 Frequency" is detected when the battery cooling blower assembly is operating and its value changes in proportion to the battery cooling blower assembly rotation speed.


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON (READY).

4.

Enter the following menus: Powertrain / HV Battery / Active Test / Control the Hybrid/EV Battery Cooling Fan.

5.

Operate the battery cooling blower assembly in each fan mode, 1 through 6, for 60 seconds or more.

HINT:

Operation of the battery cooling blower assembly can be confirmed by checking if air is sucked into the air intake port of the intake duct.


6.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

7.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A8111.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A8111

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
Only P0A8196 or P0A8198 is output A
P0A8196 or P0A8198 is output and DTCs other than the DTCs in table below are output B
P0A8196 or P0A8198 is output and hybrid battery system DTCs in table below are output C
P0A8196 or P0A8198 is output and hybrid control system DTCs in table below are output D


System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation


Post-procedure1

c.

Turn the ignition switch off.



A

2.CHECK FILTER, DUCT AND BLOWER

B

2.CHECK FILTER, DUCT AND BLOWER

C

D

2.CHECK FILTER, DUCT AND BLOWER
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the rear seat cushion leg sub-assembly.

HINT:

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL



Procedure1

c.

Check that the No. 1 HV battery intake filter, battery cooling blower assembly and No. 1 hybrid battery intake duct LH are not disconnected, damaged, or clogged with foreign matter.

A458601C01
1.417,2.49 1.823,1.906 true 4.594,2.458 5.094,1.823 true 5.427,2.469 5.677,1.896 true 1.302,2.542 1.615,2.74 0.313,0.198 10 false *1 5.292,2.51 5.604,2.708 0.313,0.198 10 false *2 4.49,2.5 4.802,2.698 0.313,0.198 10 false *3
*1 No. 1 HV Battery Intake Filter *2 Battery Cooling Blower Assembly
*3 No. 1 Hybrid Battery Intake Duct LH - -


OK:

The No. 1 HV battery intake filter, No. 1 hybrid battery intake duct LH and battery cooling blower assembly blower are not disconnected, damaged, or clogged with foreign matter.



Post-procedure1

d.

Install the rear seat cushion leg sub-assembly.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BATTERY COOLING BLOWER ASSEMBLY)

NG

CORRECT THE PROBLEM

3.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BATTERY COOLING BLOWER ASSEMBLY)

OK

4.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BATTERY COOLING BLOWER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BATTERY COOLING BLOWER ASSEMBLY)

OK

5.CHECK BATTERY ECU ASSEMBLY (GROUND SHORT CHECK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK BATTERY ECU ASSEMBLY (GROUND SHORT CHECK)

Pre-procedure1

a.

Remove the battery ECU assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



Procedure1

b.
A459830C01
0.948,2.365 1.365,2.667 0.417,0.302 0.698,3.979 1.063,3.302 true 1.594,3.958 1.208,3.448 true 0.094,0.042 0.552,0.24 0.458,0.198 10 false *a 1.49,4.021 1.948,4.219 0.458,0.198 10 false GND 1.031,2.458 1.49,2.656 0.458,0.198 10 false z12 0.604,4.021 1.063,4.219 0.458,0.198 10 false SI0
*a Component without harness connected
(Battery ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z12-23 (SI0) - z12-34 (GND) Ignition switch off 10 kΩ or higher



Post-procedure1

c.

Install the battery ECU assembly.


Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (COOLING FAN FREQUENCY)

NG

6.READ VALUE USING GTS (COOLING FAN FREQUENCY)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0A8111

Result:
Result Proceed to
Both of the value in the Data List (Hybrid/EV Battery Cooling Fan 1 Frequency) and the actual measured value at the battery ECU assembly connector are 0 Hz. A
Other than above B



A

7.CHECK BATTERY ECU ASSEMBLY

B

8.CHECK BATTERY ECU ASSEMBLY (FREQUENCY)
7.CHECK BATTERY ECU ASSEMBLY

OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY

NG

8.CHECK BATTERY ECU ASSEMBLY (FREQUENCY)

OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY

NG