Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2020.03–2020.07
RM36W0E _57 Power Source / Network _088060 NETWORKING _0420500 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B120687  P/W Master SW System Missing Message  B232187  D-Door P/W System Missing Message  B232287  P-Door P/W System Missing Message  B232387  RR-Door P/W System Missing Message  B232487  RL-Door P/W System Missing Message  


DESCRIPTION

This DTC is stored when LIN communication between the main body ECU (multiplex network body ECU) and multiplex network master switch assembly, front power window regulator motor assembly RH, front power window regulator motor assembly LH, rear power window regulator motor assembly RH or rear power window regulator motor assembly LH stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B120687 P/W Master SW System Missing Message No communication between multiplex network master switch assembly and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Multiplex network master switch assembly

·

Wire harness or connector


B232187 D-Door P/W System Missing Message No communication between front power window regulator motor assembly RH and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Multiplex network master switch assembly

·

Front power window regulator motor assembly RH

·

Wire harness or connector


B232287 P-Door P/W System Missing Message No communication between front power window regulator motor assembly LH and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Front power window regulator motor assembly LH

·

Wire harness or connector


B232387 RR-Door P/W System Missing Message No communication between rear power window regulator motor assembly RH and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Rear power window regulator motor assembly RH

·

Wire harness or connector


B232487 RL-Door P/W System Missing Message No communication between rear power window regulator motor assembly LH and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Rear power window regulator motor assembly LH

·

Wire harness or connector



WIRING DIAGRAM

C436187E02
0.615,3.406 2.448,3.625 1.833,0.219 10 false : LIN Communication Line 0.115,2.083 1.74,2.677 1.625,0.594 10 false Main Body ECU (Multiplex Network Body ECU) 1.885,1.792 3.021,2.406 1.135,0.615 10 false Power Distribution Box Assembly 0.094,1.917 0.625,2.219 0.531,0.302 10 false MB 1.302,1.406 1.854,1.615 0.552,0.208 10 false LIN2 2.823,1.406 3.375,1.615 0.552,0.208 10 false 4E 1.698,1.25 1.948,1.417 0.25,0.167 10 false 15 2.813,1.188 3.063,1.354 0.25,0.167 10 false 17 6.542,3.438 6.698,3.635 0.156,0.198 10 false A

C407699E12
3.031,1.281 3.323,1.5 0.292,0.219 10 false K5 3.031,1.438 4.615,1.969 1.583,0.531 10 false Multiplex Network Master Switch Assembly 3.969,0.615 4.323,0.844 0.354,0.229 10 false LIN1 3.958,0.99 4.313,1.219 0.354,0.229 10 false LIN2 4.344,0.844 4.698,1.073 0.354,0.229 10 false 16 4.344,0.438 4.698,0.667 0.354,0.229 10 false 17 3.25,1 3.604,1.229 0.354,0.229 10 false GND 3.25,0.604 3.74,0.833 0.49,0.229 10 false B 3.01,0.49 3.365,0.719 0.354,0.229 10 false 11 3.01,0.885 3.365,1.115 0.354,0.229 10 false 12 1.792,0.771 2.656,1.021 0.865,0.25 10 false ECU-B NO. 2 1.865,2.708 2.729,2.958 0.865,0.25 10 false DOOR F/R 2.927,3.135 3.219,3.354 0.292,0.219 10 false K7 2.917,3.292 4.844,3.729 1.927,0.438 10 false Front Power Window Regulator Motor Assembly RH 4.031,2.74 4.385,2.969 0.354,0.229 10 false LIN 4.344,2.583 4.698,2.813 0.354,0.229 10 false 9 3.281,2.948 3.635,3.177 0.354,0.229 10 false GND 3.063,2.844 3.417,3.073 0.354,0.229 10 false 1 3.271,2.552 3.625,2.781 0.354,0.229 10 false B 3.083,2.427 3.438,2.656 0.354,0.229 10 false 2 1.854,4.302 2.719,4.552 0.865,0.25 10 false DOOR F/L 3.25,4.521 3.604,4.75 0.354,0.229 10 false GND 3.083,4.396 3.438,4.625 0.354,0.229 10 false 1 3.271,4.094 3.625,4.323 0.354,0.229 10 false B 3.104,3.99 3.458,4.219 0.354,0.229 10 false 2 4.042,4.333 4.396,4.563 0.354,0.229 10 false LIN 4.385,4.156 4.74,4.385 0.354,0.229 10 false 9 2.948,4.927 4.875,5.51 1.927,0.583 10 false Front Power Window Regulator Motor Assembly LH 2.969,4.75 3.26,4.969 0.292,0.219 10 false L7 2.938,6.521 4.823,6.938 1.885,0.417 10 false Rear Power Window Regulator Motor Assembly LH 2.948,6.365 3.24,6.583 0.292,0.219 10 false N4 3.25,6.135 3.604,6.365 0.354,0.229 10 false GND 3.271,5.75 3.625,5.979 0.354,0.229 10 false B 3.094,5.677 3.448,5.906 0.354,0.229 10 false 2 4.031,5.917 4.385,6.146 0.354,0.229 10 false LIN 4.354,5.802 4.708,6.031 0.354,0.229 10 false 9 1.896,5.927 2.76,6.177 0.865,0.25 10 false DOOR R/L 3.073,6.031 3.427,6.26 0.354,0.229 10 false 1 1.875,7.479 2.74,7.729 0.865,0.25 10 false DOOR R/R 2.969,7.958 3.26,8.177 0.292,0.219 10 false M4 2.958,8.115 4.854,8.604 1.896,0.49 10 false Rear Power Window Regulator Motor Assembly RH 4.042,7.458 4.396,7.688 0.354,0.229 10 false LIN 4.344,7.333 4.698,7.563 0.354,0.229 10 false 9 3.26,7.656 3.615,7.885 0.354,0.229 10 false GND 3.073,7.573 3.427,7.802 0.354,0.229 10 false 1 3.292,7.281 3.646,7.51 0.354,0.229 10 false B 3.094,7.219 3.448,7.448 0.354,0.229 10 false 2 0.656,8.219 2.521,8.427 1.865,0.208 10 false : LIN Communication Line 0.146,0.573 1.75,0.854 1.604,0.281 10 false from Auxiliary Battery 0.115,2.51 1.719,2.792 1.604,0.281 10 false from Auxiliary Battery 0.115,4.104 1.719,4.385 1.604,0.281 10 false from Auxiliary Battery 0.135,5.729 1.74,6.01 1.604,0.281 10 false from Auxiliary Battery 0.115,7.271 1.719,7.552 1.604,0.281 10 false from Auxiliary Battery 6.417,0.063 6.573,0.26 0.156,0.198 10 false A

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC is B232588 output A
DTC B120687, B232187, B232287, B232387 and B232487 are output B
DTC B120687 and B232187 are output C
Only DTC B120687 is output D
Only DTC B232187 is output E
Only DTC B232287 is output F
Only DTC B232387 is output G
Only DTC B232487 is output H
DTC is not output I



A

B

3.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

C

5.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

D

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)

E

7.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

F

10.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

G

12.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

H

14.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

I

3.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the K5 multiplex network master switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
4E-17 - K5-17 (LIN1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT POWER DISTRIBUTION BOX ASSEMBLY
a.

Remove the power distribution box assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

C433197C02
1.875,0.333 2.292,0.583 0.417,0.25 5.5,0.083 5.917,0.333 0.417,0.25 2.271,0.927 2.469,1.385 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 2.01,0.385 2.323,0.542 0.313,0.156 10 false MB 5.615,0.125 5.927,0.281 0.313,0.156 10 false 4E 2.323,1.417 2.74,1.594 0.417,0.177 10 false LIN2
*a Component without harness connected
(Power Distribution Box Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

This inspection is to check the LIN communication line in the power distribution box assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


Standard Resistance:
Tester Connection Condition Specified Condition
4E-17 - MB-15 (LIN2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the K5 multiplex network master switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
4E-17 - K5-17 (LIN1) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the K5 multiplex network master switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K5-11 (B) - K5-12 (GND) Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K5-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the K7 front power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4E-17 - K7-9 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - AUXILIARY BATTERY AND BODY GROUND)

NG

9.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
8.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the K7 front power window regulator motor assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K7-2 (B) - K7-1 (GND) Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K7-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the K5 multiplex network master switch assembly connector.


b.

Disconnect the K7 front power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Condition Specified Condition
4E-17 - K7-9 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the L7 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
4E-17 - L7-9 (LIN) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the L7 front power window regulator motor assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L7-2 (B) - L7-1 (GND) Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L7-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the M4 rear power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
4E-17 - M4-9 (LIN) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the M4 rear power window regulator motor assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M4-2 (B) - M4-1 (GND) Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M4-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the 4E power distribution box assembly connector.


b.

Disconnect the N4 rear power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
4E-17 - N4-9 (LIN) Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the N4 rear power window regulator motor assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N4-2 (B) - N4-1 (GND) Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N4-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR