Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for HV Model)
RM36W0E _58 Vehicle Interior _088019 HEATING / AIR CONDITIONING _0420299 AIR CONDITIONING SYSTEM(for HV Model) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for HV Model)  P1C7C49  Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure  


DESCRIPTION

This DTC is stored if there is insulation malfunction in the high-voltage circuit in the air conditioning system. Possible causes are poor insulation in the compressor with motor assembly, or mixing of any oil other than ND-OIL 11 in the refrigerant cycle.

HINT:

A high-voltage motor is built into the compressor with motor assembly and is cooled directly with refrigerant. Compressor oil (ND-OIL 11) with high insulation performance is used because leakage of electrical power may occur if regular compressor oil (ND-OIL 8) is used.


DTC No. Detection Item DTC Detection Condition Trouble Area Memory
P1C7C49 Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure Diagnosis Condition:

None


Malfunction Status:

High voltage system insulation malfunction


Detection Time:

None


·

Compressor oil

·

Refrigerant pipe line

·

Compressor with motor assembly


Memorized

WIRING DIAGRAM

E389760E07
0.125,0.979 2.51,1.167 2.385,0.188 10 false Air Conditioning Amplifier Assembly 0.156,2.469 2.542,2.656 2.385,0.188 10 false Battery State Sensor Assembly 0.146,6.406 2.521,6.729 2.375,0.323 10 false Compressor with Motor Assembly 5.031,6.917 7.052,7.344 2.021,0.427 10 false Inverter with Converter Assembly 2.583,5.969 4.708,6.354 2.125,0.385 10 false HV Air Conditioning Wire 2.25,7.021 4.24,7.281 1.99,0.26 10 false : CAN Communication Line 2.24,7.427 4.031,7.729 1.792,0.302 10 false : LIN Communication Line 5.385,3.875 7.156,4.25 1.771,0.375 10 false Hybrid Vehicle Control ECU 0.177,2.313 0.552,2.51 0.375,0.198 10 false O68 0.938,1.823 1.313,2.021 0.375,0.198 10 false LIN 6.031,3.219 6.406,3.417 0.375,0.198 10 false LIN3 5.375,3.708 5.75,3.906 0.375,0.198 10 false A68 3.76,3.781 5.031,4.021 1.271,0.24 10 false from IGP Relay 2.188,3.927 3.25,4.115 1.063,0.188 10 false ECU-IGP NO. 3 1.25,1.667 1.625,1.865 0.375,0.198 10 false 2 5.75,3.063 6.125,3.26 0.375,0.198 10 false 28 1.313,3.229 1.688,3.427 0.375,0.198 10 false D75 1.333,3.792 1.708,3.99 0.375,0.198 10 false D75 1.313,4.354 1.688,4.552 0.375,0.198 10 false D75 1.365,5.125 1.74,5.323 0.375,0.198 10 false b1 1.365,5.646 1.74,5.844 0.375,0.198 10 false b1 0.771,3.229 1.375,3.479 0.604,0.25 10 false DOUT 0.938,3.781 1.313,3.979 0.375,0.198 10 false IG1 0.865,4.344 1.24,4.542 0.375,0.198 10 false GND 0.969,5.135 1.344,5.333 0.375,0.198 10 false PB 0.958,5.656 1.333,5.854 0.375,0.198 10 false PE 5.292,5.021 5.74,5.219 0.448,0.198 10 false ACPB 5.292,5.531 5.74,5.729 0.448,0.198 10 false ACPE 5.042,6.75 5.417,6.948 0.375,0.198 10 false b2 1.406,3 1.781,3.198 0.375,0.198 10 false 3 1.406,3.573 1.781,3.771 0.375,0.198 10 false 1 1.406,4.135 1.781,4.333 0.375,0.198 10 false 2 1.406,4.917 1.781,5.115 0.375,0.198 10 false 2 1.396,5.448 1.771,5.646 0.375,0.198 10 false 1 5.083,5.021 5.458,5.219 0.375,0.198 10 false 1 5.073,5.552 5.448,5.75 0.375,0.198 10 false 2

CAUTION / NOTICE / HINT

CAUTION:
·

When performing troubleshooting for P1C7C49, be sure to use tools wrapped in insulating tape. (It is extremely dangerous if high voltage is short circuited to the ground via a tool.)

·

Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION



NOTICE:
·

Electrical insulation performance may decrease significantly if even a small amount of oil other than ND-OIL 11 is used (or enters) in the refrigerant cycle, causing a DTC to be output.

·

Replace the main components of the refrigerant cycle (evaporator, condenser, and compressor) if a large amount of oil other than ND-OIL 11 enters the system. Failing to do so may cause electrical insulation performance to remain low, causing a DTC to be stored.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When the cable is disconnected from the negative (-) auxiliary battery terminal, the memory of various systems will be cleared. Because of this, be sure to make a record of the contents memorized in each system before starting work. When work is finished, adjust each system to its previous state.

·

The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs for both systems are output simultaneously.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

·

The air conditioning system uses the CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the air conditioning system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING



HINT:

When using a megohmmeter to measure the electrical resistance, use the 500 V range.


PROCEDURE

1.CHECK COMPRESSOR OIL
a.

Check that no types of compressor oil other than ND-OIL 11 (such as ND-OIL 8, etc.) were used in the past.

HINT:
·

Electrical insulation performance may decrease significantly if even a small amount of oil other than ND-OIL 11 is used (or enters) in the refrigerant cycle, causing a DTC to be output.

·

Replace the main components of the refrigerant cycle (evaporator, condenser, and compressor) if a large amount of oil other than ND-OIL 11 enters the system. Failing to do so may cause electrical insulation performance to remain low, causing a DTC to be stored.




Result:
Proceed to
OK
NG



OK

2.CLEAR DTC

NG

2.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Hybrid Control > Clear DTCs
50002 397

Result:
Proceed to
NEXT



NEXT

3.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY (PE - BODY GROUND)
3.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY (PE - BODY GROUND)
CAUTION:

Because the compressor with motor assembly has a high-voltage circuit, put on insulated gloves and remove the service plug grip to cut off the high-voltage circuit before inspecting the compressor with motor assembly.


Pre-procedure1

a.

Turn the ignition switch ON (READY).


b.

Prepare the vehicle according to the table below for 3 minutes.

Item Condition
Blower speed HI
Temperature setting MAX COLD
A/C switch On


c.

Turn the ignition switch off.


d.

Remove the service plug grip.

HINT:

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


NOTICE:
·

After removing the service plug grip, turning the ignition switch ON (READY) may cause a malfunction. Do not turn the ignition switch ON (READY) with the service plug grip removed.

·

Turning the ignition switch ON (READY) with connectors disconnected with cause other DTCs to be stored, so clear the DTCs after the inspection.



HINT:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>DTC CHECK / CLEAR



e.

Disconnect the compressor with motor assembly connector.


Procedure1

f.
E437396C01
1.531,0.25 1.948,0.5 0.417,0.25 2.156,1.646 1.969,1.229 true 2.146,1.688 2.479,1.885 0.333,0.198 10 false PE 0.271,0.219 0.583,0.417 0.313,0.198 10 false *a 1.677,0.313 1.99,0.51 0.313,0.198 10 false b1
*a Component without harness connected
(Compressor with Motor Assembly)


Using a megohmmeter, measure the resistance according to the value(s) in the table below.

CAUTION:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
b1-1 (PE) - Body ground Always 2 MΩ or higher


NOTICE:

If the result is NG, it can be suspected that an oil other than ND-OIL 11 has been mixed into the refrigeration cycle. Because the electrical insulation performance cannot be restored by cleaning and replacing the oil, it is necessary to replace all the components related to the refrigeration cycle (No. 1 cooler evaporator, cooler condenser assembly, compressor with motor assembly, cooler expansion valve, and piping).



Post-procedure1

g.

None


Result:
Proceed to
OK
NG



OK

4.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY (PB - BODY GROUND)

NG

4.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY (PB - BODY GROUND)
CAUTION:

Because the compressor with motor assembly has a high-voltage circuit, put on insulated gloves and remove the service plug grip to cut off the high-voltage circuit before inspecting the compressor with motor assembly.


a.
E437396C02
1.531,0.25 1.948,0.5 0.417,0.25 1.313,1.656 1.521,1.208 true 1.198,1.688 1.531,1.885 0.333,0.198 10 false PB 0.271,0.219 0.583,0.417 0.313,0.198 10 false *a 1.677,0.313 1.99,0.51 0.313,0.198 10 false b1
*a Component without harness connected
(Compressor with Motor Assembly)


Using a megohmmeter, measure the resistance according to the value(s) in the table below.

CAUTION:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
b1-2 (PB) - Body ground Always 2 MΩ or higher


NOTICE:

If the result is NG, it can be suspected that an oil other than ND-OIL 11 has been mixed into the refrigeration cycle. Because the electrical insulation performance cannot be restored by cleaning and replacing the oil, it is necessary to replace all the components related to the refrigeration cycle (No. 1 cooler evaporator, cooler condenser assembly, compressor with motor assembly, cooler expansion valve, and piping).



Result:
Proceed to
OK
NG



OK

5.INSPECT REFRIGERANT CYCLE (PE - BODY GROUND)

NG

5.INSPECT REFRIGERANT CYCLE (PE - BODY GROUND)
CAUTION:

Because the compressor with motor assembly has a high-voltage circuit, put on insulated gloves and remove the service plug grip to cut off the high-voltage circuit before inspecting the compressor with motor assembly.


Pre-procedure1

a.

Connect the b1 compressor with motor assembly connector.


b.

Install the service plug grip.

HINT:

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



c.

Turn the ignition switch ON (READY).


d.

Set the A/C temperature to 25°C (77°F) and blower switch to LO and operate the compressor with motor assembly for 10 minutes to circulate the refrigerant and collect as much compressor oil as possible in the compressor with motor assembly.


e.

Using a spot cooler or other tool, cool down the compressor with motor assembly for 30 minutes, or leave the vehicle overnight before inspection.

NOTICE:

Do not operate the compressor before inspection.



f.

Turn the ignition switch off.


g.

Remove the service plug grip.

HINT:

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


NOTICE:
·

After removing the service plug grip, turning the ignition switch ON (READY) may cause a malfunction. Do not turn the ignition switch ON (READY) with the service plug grip removed.

·

Turning the ignition switch ON (READY) with connectors disconnected with cause other DTCs to be stored, so clear the DTCs after the inspection.



HINT:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>DTC CHECK / CLEAR



h.

Disconnect the compressor with motor assembly connector.


Procedure1

i.
E437396C01
1.531,0.25 1.948,0.5 0.417,0.25 2.156,1.646 1.969,1.229 true 2.146,1.688 2.479,1.885 0.333,0.198 10 false PE 0.271,0.219 0.583,0.417 0.313,0.198 10 false *a 1.677,0.313 1.99,0.51 0.313,0.198 10 false b1
*a Component without harness connected
(Compressor with Motor Assembly)


Using a megohmmeter, measure the resistance according to the value(s) in the table below.

CAUTION:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
b1-1 (PE) - Body ground Always 3 MΩ or higher


NOTICE:

If the result is NG, it can be suspected that an oil other than ND-OIL 11 has been mixed into the refrigeration cycle. Because the electrical insulation performance cannot be restored by cleaning and replacing the oil, it is necessary to replace all the components related to the refrigeration cycle (No. 1 cooler evaporator, cooler condenser assembly, compressor with motor assembly, cooler expansion valve, and piping).



Post-procedure1

j.

None


Result:
Proceed to
OK
NG



OK

6.INSPECT REFRIGERANT CYCLE (PB - BODY GROUND)

NG

6.INSPECT REFRIGERANT CYCLE (PB - BODY GROUND)
CAUTION:

Because the compressor with motor assembly has a high-voltage circuit, put on insulated gloves and remove the service plug grip to cut off the high-voltage circuit before inspecting the compressor with motor assembly.


a.
E437396C02
1.531,0.25 1.948,0.5 0.417,0.25 1.313,1.656 1.521,1.208 true 1.198,1.688 1.531,1.885 0.333,0.198 10 false PB 0.271,0.219 0.583,0.417 0.313,0.198 10 false *a 1.677,0.313 1.99,0.51 0.313,0.198 10 false b1
*a Component without harness connected
(Compressor with Motor Assembly)


Using a megohmmeter, measure the resistance according to the value(s) in the table below.

CAUTION:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
b1-2 (PB) - Body ground Always 3 MΩ or higher


NOTICE:

If the result is NG, it can be suspected that an oil other than ND-OIL 11 has been mixed into the refrigeration cycle. Because the electrical insulation performance cannot be restored by cleaning and replacing the oil, it is necessary to replace all the components related to the refrigeration cycle (No. 1 cooler evaporator, cooler condenser assembly, compressor with motor assembly, cooler expansion valve, and piping).



Result:
Proceed to
OK
NG



OK

NG