Home › Vehicle Exterior › WINDOW / GLASS › WINDOW DEFOGGER SYSTEM › 2020.03–2020.07
RM36W0E _59 Vehicle Exterior _088018 WINDOW / GLASS _0420294 WINDOW DEFOGGER SYSTEM J

WINDOW / GLASS  WINDOW DEFOGGER SYSTEM  Rear Window Defogger System does not Operate  


DESCRIPTION

for Manual Air Conditioning System:

When the rear window defogger switch on the No. 1 heater control sub-assembly is pressed, the operation signal is transmitted to the air conditioning amplifier assembly and power distribution box assembly via LIN communication. When the power distribution box assembly receives the signal, it turns on the DEF relay to operate the window defogger system.


for Automatic Air Conditioning System:

An operation request signal is sent to the air conditioning amplifier assembly via LIN communication when the rear window defogger switch (air conditioning control assembly) is operated. When the air conditioning amplifier assembly receives the signal, it sends an operation request signal via CAN communication to the main body ECU (multiplex network body ECU).When the main body ECU (multiplex network body ECU) receives the signal, it sends an operation request signal via CPXI communication to the power distribution box assembly. After the operation request signal is received by the power distribution box assembly it outputs an operation signal and operates the window defogger.


WIRING DIAGRAM

E426700E04
6.021,5.323 6.177,5.521 0.156,0.198 10 false E 5.01,5.302 5.167,5.5 0.156,0.198 10 false B 3.094,3.438 5.396,3.729 2.302,0.292 10 false No. 1 Heater Control Sub-assembly 6.26,5.417 6.573,5.615 0.313,0.198 10 false Y9 1.208,4.896 1.615,5.083 0.406,0.188 10 false IC 1.188,6.313 3.313,6.563 2.125,0.25 10 false Power Distribution Box Assembly 4.708,5.802 6.458,6.26 1.75,0.458 10 false Rear Window Defogger Wire (Back Door Glass) 3.094,3.271 3.552,3.469 0.458,0.198 10 false H56 5.635,1.438 6.25,1.635 0.615,0.198 10 false IG+ 2.354,2.76 2.969,2.958 0.615,0.198 10 false ERDF 5.51,2.802 6.125,3 0.615,0.198 10 false RDEF 3.76,4.396 4.167,4.583 0.406,0.188 10 false 4C 3.76,4.198 4.167,4.385 0.406,0.188 10 false 24 2.625,4.729 3.031,4.917 0.406,0.188 10 false +B1 3.75,5.427 4.156,5.615 0.406,0.188 10 false 4E 3.75,5.219 4.156,5.406 0.406,0.188 10 false 43 4.698,5.417 5.01,5.615 0.313,0.198 10 false X3 0.177,0.198 4.031,0.438 3.854,0.24 12 false for Manual Air Conditioning System: 4.708,5.219 5.115,5.406 0.406,0.188 10 false 1 6.292,5.208 6.698,5.396 0.406,0.188 10 false 1 6.01,2.802 6.417,2.99 0.406,0.188 10 false 6 2.156,2.76 2.563,2.948 0.406,0.188 10 false 2 6,1.438 6.406,1.625 0.406,0.188 10 false 5 3.052,1.396 3.667,1.594 0.615,0.198 10 false OFF 3.479,1.396 4.094,1.594 0.615,0.198 10 false ON 2.333,2.042 4.635,2.333 2.302,0.292 10 false Rear Window Defogger Switch 2.781,1.604 3.396,1.802 0.615,0.198 10 false - 2.781,1.833 3.396,2.031 0.615,0.198 10 false - 2.938,2.667 3.979,3.073 1.042,0.406 10 false Timer circuit 3.615,0.49 4.854,0.771 1.24,0.281 10 false from IGP Relay 5.167,0.698 6.406,0.979 1.24,0.281 10 false ECU-IGP NO. 3 1.833,5.688 2.469,5.906 0.635,0.219 10 false RR DEF

E426701E07
0.24,0.219 4.458,0.458 4.219,0.24 12 false for Automatic Air Conditioning System: 5.115,1.719 6.583,2.156 1.469,0.438 10 false Air Conditioning Control Assembly 0.625,4.979 2.281,5.438 1.656,0.458 10 false Main Body ECU (Multiplex Network Body ECU) 2.938,4.99 5.073,5.219 2.135,0.229 10 false Power Distribution Box Assembly 5.438,3.906 5.75,4.104 0.313,0.198 10 false 43 5.438,4.104 5.75,4.302 0.313,0.198 10 false 4E 2.26,3.5 2.583,3.677 0.323,0.177 10 false 22 2.25,3.708 2.563,3.906 0.313,0.198 10 false MB 3.01,1.719 4.583,2.177 1.573,0.458 10 false Air Conditioning Amplifier Assembly 5.438,6.25 5.75,6.448 0.313,0.198 10 false X3 3.542,6.25 3.854,6.448 0.313,0.198 10 false Y9 3.896,6.156 4.208,6.354 0.313,0.198 10 false E 5.177,6.156 5.49,6.354 0.313,0.198 10 false B 0.729,6.615 2.792,6.854 2.063,0.24 10 false : CAN Communication Line 0.74,6.99 2.677,7.208 1.938,0.219 10 false : LIN Communication Line 0.729,7.365 2.708,7.646 1.979,0.281 10 false : CXPI Communication Line 3.719,6.708 5.458,7.427 1.74,0.719 10 false Rear Window Defogger Wire (Back Door Glass) 3.583,6.052 3.906,6.229 0.323,0.177 10 false 1 3.177,3.688 3.49,3.885 0.313,0.198 10 false IC 5.469,6.042 5.792,6.219 0.323,0.177 10 false 1 3.802,4.365 4.448,4.573 0.646,0.208 10 false RR DEF 4.563,3.427 5.208,3.635 0.646,0.208 10 false +B1 1.802,3.708 2.417,3.906 0.615,0.198 10 false CXPI

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

With the negative (-) battery terminal connected, disconnect/do not connect the connector of the power distribution box assembly.

·

When replacing the power distribution box assembly, the system may not operate normally if the same part number is not used.

·

The window defogger system uses the CAN communication system, LIN communication system and CXPI communication system. Inspect the communication function by following How to Proceed with Troubleshooting.

Troubleshoot the window defogger system after confirming that the communication system is functioning properly.*1

Click hereVehicle Exterior>WINDOW / GLASS>WINDOW DEFOGGER SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

*1: for Automatic Air Conditioning System




PROCEDURE

1.READ VALUE USING GTS (REAR DEFOGGER INPUT SIGNAL)
a.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Defogger Input Signal Window defogger switch signal input condition ON or OFF ON: Rear window defogger switch is on
OFF: Rear window defogger switch is off
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Rear Defogger Input Signal
50003 475 1280
OK:

The Data List value displays "ON" with the rear window defogger switch set to ON.



Result:
Result Proceed to
OK A
NG (for Automatic Air Conditioning System) B
NG (for Manual Air Conditioning System) C



A

2.READ VALUE USING GTS (REAR DEFOGGER OUTPUT SIGNAL)

B

5.CHECK AIR CONDITIONING SYSTEM

C

8.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - NO. 1 HEATER CONTROL SUB-ASSEMBLY)
2.READ VALUE USING GTS (REAR DEFOGGER OUTPUT SIGNAL)
a.

Using the GTS, read the Data List.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Defogger Output Signal Window defogger output condition ON or OFF ON: Window defogger operates
OFF: Window defogger does not operate
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Rear Defogger Output Signal
50003 475 1281
OK:

When the rear window defogger switch is ON, the data monitor standard value is "ON".



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR WINDOW DEFOGGER WIRE [BACK DOOR GLASS])

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR WINDOW DEFOGGER WIRE [BACK DOOR GLASS])
a.

Disconnect the X3 rear window defogger wire (back door glass) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4E-43 - X3-1 (B) Always Below 1 Ω
4E-43 or X3-1 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (REAR WINDOW DEFOGGER WIRE [BACK DOOR GLASS] - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (REAR WINDOW DEFOGGER WIRE [BACK DOOR GLASS] - BODY GROUND)
a.

Disconnect the Y9 rear window defogger wire (back door glass) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y9-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR REAR WINDOW DEFOGGER WIRE (BACK DOOR GLASS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK AIR CONDITIONING SYSTEM
a.

Check the air conditioning system.


HINT:

Both the window defogger system operation signal and air conditioning system operation signal are transmitted to the air conditioning amplifier assembly via the same communication line.


OK:

The air conditioning system operates normally.



Result:
Result Proceed to
OK A
NG (for HV Model) B
NG (for Gasoline Model) C



A

6.CHECK AIR CONDITIONING CONTROL ASSEMBLY

B

C

6.CHECK AIR CONDITIONING CONTROL ASSEMBLY
a.

Check that the defogger indicator illuminates when the window defogger switch is on.

OK:

Defogger indicator illuminates.



Result:
Proceed to
OK
NG



OK

7.PERFORM ACTIVE TEST USING GTS

NG

7.PERFORM ACTIVE TEST USING GTS
a.

Using the GTS, perform the Active Test.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range
Rear Defogger Relay Rear window defogger wire (Back door glass) OFF or ON
Body Electrical > Air Conditioner > Active Test
Tester Display
Rear Defogger Relay
50004 450 7
OK:

Rear window defogger wire (back door glass) warms up.



Result:
Proceed to
OK
NG



OK

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - NO. 1 HEATER CONTROL SUB-ASSEMBLY)
a.

Disconnect the 4C power distribution box assembly connector.


b.

Disconnect the H56 No. 1 heater control sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4C-24 - H56-6 (RDEF) Always Below 1 Ω
4C-24 or H56-6 (RDEF) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (NO. 1 HEATER CONTROL SUB-ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (NO. 1 HEATER CONTROL SUB-ASSEMBLY - BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H56-5 (IG+) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H56-2 (ERDF) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR