Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK › 2020.03–2020.07
RM36W0E _58 Vehicle Interior _088479 DOOR LOCK _0421643 REAR DOOR LOCK A

DOOR LOCK  REAR DOOR LOCK  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the RH side.



PROCEDURE

Hide 69770B 1.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B576097

Engage the guide to install the rear door inside locking cable assembly to the rear door lock assembly.


b.
B566013C02
0,0 0,0 false
V113147

Install in this Direction


Engage the claws as shown in the illustration.


Hide 69730D 2.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B576096

Engage the guide to install the rear door lock remote control cable assembly to the rear door lock assembly.


b.
B566014C02
0,0 0,0 false
V113147

Install in this Direction


Engage the claws as shown in the illustration.


Hide 69330 3.INSTALL REAR DOOR LOCK ASSEMBLY

NOTICE:
·

When reusing a removed rear door lock assembly, replace the door lock wiring harness seal with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

·

Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the rear door lock assembly.



a.

Apply MP grease to the sliding parts of the rear door lock assembly.


b.

When reusing the rear door lock assembly:

i.
B576095

Install a new door lock wiring harness seal to the rear door lock assembly.



c.
B566015

Connect the rear door lock assembly to the release plate of the rear door outside handle frame sub-assembly as shown in the illustration, and set it to the rear door panel.

HINT:

Make sure that the release plate of the rear door outside handle frame sub-assembly is securely connected to the rear door lock assembly.



d.

Using a T30 "TORX" socket wrench, install the rear door lock assembly with the 3 screws.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


e.

Connect the connector.


Hide 68103 4.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

Hide 67407E 5.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

Hide 68142C 6.INSTALL REAR DOOR GLASS RUN

Hide 67841E 7.INSTALL REAR DOOR SERVICE HOLE COVER (w/ Rear Speaker)

Hide 67841E 8.INSTALL REAR DOOR SERVICE HOLE COVER (w/o Rear Speaker)

Hide 68198 9.INSTALL REAR DOOR BELT REAR SEAL

Hide 68196B 10.INSTALL REAR DOOR BELT FRONT SEAL

Hide 68173B 11.INSTALL REAR DOOR GLASS INNER WEATHERSTRIP

Hide 67603 12.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 13.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL

Hide 67673A 14.INSTALL REAR DOOR FRAME GARNISH

Hide 15.CONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 16. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 17. INITIALIZE POWER WINDOW CONTROL SYSTEM