Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › 2020.03–2020.07
RM36W0E _59 Vehicle Exterior _088480 DOOR / HATCH _0421654 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the RH side.



PROCEDURE

Hide 67837C 1.INSTALL REAR DOOR DUST PROOF SEAL

a.
B621542

Engage the claws to install 2 new rear door dust proof seals.

NOTICE:

Even if there were 3 dust proof seals at the time of removal, install 2 dust proof seals as shown in the illustration.



Hide 67871 2.INSTALL REAR DOOR WEATHERSTRIP

a.
B565018C01
0.385,0.75 0.802,0.333 true 0.25,0.719 0.563,0.917 0.313,0.198 10 false *a
*a Clip A


Engage the clip A and other clips to install the rear door weatherstrip.


Hide 68630D 3.INSTALL REAR DOOR CHECK ASSEMBLY

a.

Clean the bolt hole in the vehicle body.


b.

Clean the threads of the bolt A.


c.

Apply adhesive to the threads of the bolt A.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
B565017C01
2.438,1.521 2.604,1.688 0.167,0.167 10 true *a 1.573,1.406 1.74,1.573 0.167,0.167 10 true *b 1.563,0.698 1.729,0.865 0.167,0.167 10 true *b
*a Bolt A
*b Bolt B


Install the rear door check assembly with the bolt A and 2 bolts B.

Torque:
Bolt A : 30 N*m (306 kgf*cm, 22 ft.*lbf)
Bolt B : 5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 75923 5.INSTALL NO. 2 BLACK OUT TAPE

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE (for Rear Door)>INSTALLATION


Hide 68180C 6.INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR DOOR BELT MOULDING>INSTALLATION


Hide 75707 7.INSTALL REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR DOOR WINDOW FRAME MOULDING>INSTALLATION


Hide 69203A 8.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts on the rear door outside handle frame sub-assembly.


b.
B565020C02
0,0 0,0 false
V113147

Install in this Direction


Engage the guides to install the rear door outside handle frame sub-assembly as shown in the illustration.


c.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242G 9.INSTALL REAR DOOR OUTSIDE HANDLE REAR PAD

B565014

a.

Engage the guides to install the rear door outside handle rear pad.


Hide 69241G 10.INSTALL REAR DOOR OUTSIDE HANDLE FRONT PAD

B565013

a.

Engage the guide and claws to install the rear door outside handle front pad.


Hide 69227J 11.INSTALL REAR DOOR OUTSIDE HANDLE COVER

a.
B565012

Engage the claws to install the rear door outside handle cover.


b.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69230 12.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B565024C02
0,0 0,0 false
V113147

Install in this Direction


Install the rear door outside handle assembly as shown in the illustration.


b.
B565025

Move the lever and engage the claws as shown in the illustration.


Hide 69330 13.INSTALL REAR DOOR LOCK ASSEMBLY

Hide 14.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door window regulator assembly.


b.
B565008

Install the rear door window regulator assembly with the 6 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

Connect the connector.


d.

Engage the clamp.


Hide 68103 15.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

a.

Connect the rear power window regulator switch assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Move the rear door glass sub-assembly so that the door glass bolt holes can be seen.


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.


e.

Disconnect the rear power window regulator switch assembly.


f.
B576061C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Insert the rear door glass sub-assembly into the rear door panel as shown in the illustration.

NOTICE:

Be careful not to damage the rear door glass sub-assembly.



g.

Install the rear door glass sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 67407E 16.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

a.

Install the rear door window division bar sub-assembly with the 2 bolts and nut.

Torque:
Nut : 6.0 N*m (61 kgf*cm, 53 in.*lbf)
Bolt : 8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 68142C 17.INSTALL REAR DOOR GLASS RUN

a.
B565009

Install the rear door glass run.


Hide 67841E 18.INSTALL REAR DOOR SERVICE HOLE COVER (w/ Rear Speaker)

a.

Apply new butyl tape to the rear door panel.


b.
B576062C01
0.354,0.604 0.729,0.604 true 3.125,0.5 2.729,0.5 true 3.042,3.188 2.76,2.969 true 0.125,0.521 0.333,0.719 0.208,0.198 10 true *a 3.104,0.406 3.313,0.615 0.208,0.208 10 true *a 3.052,3.083 3.25,3.292 0.198,0.208 10 true *a
*a Reference Point
V100143

Butyl Tape


Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and wire harness through a new rear door service hole cover.


c.

Install the rear door service hole cover according to the reference points on the rear door panel.

NOTICE:

Securely install the rear door service hole cover preventing wrinkles and air bubbles.



Hide 67841E 19.INSTALL REAR DOOR SERVICE HOLE COVER (w/o Rear Speaker)

a.

Apply new butyl tape to the rear door panel.


b.
B576063C01
0.344,0.271 0.708,0.542 true 2.729,0.563 3.083,0.229 true 2.719,2.938 3.052,3.156 true 0.146,0.146 0.365,0.354 0.219,0.208 10 true *a 3.073,0.115 3.281,0.313 0.208,0.198 10 true *a 3.052,3.042 3.271,3.26 0.219,0.219 10 true *a
*a Reference Point
V100143

Butyl Tape


Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and wire harness through a new rear door service hole cover.


c.

Install the rear door service hole cover according to the reference points on the rear door panel.

NOTICE:

Securely install the rear door service hole cover preventing wrinkles and air bubbles.



Hide 86160B 20.INSTALL REAR SPEAKER ASSEMBLY (w/ Rear Speaker)

Hide 68198 21.INSTALL REAR DOOR BELT REAR SEAL

a.
B565031

Install the rear door belt rear seal to the rear door glass inner weatherstrip.


Hide 68196B 22.INSTALL REAR DOOR BELT FRONT SEAL

a.
B576057

Install the rear door belt front seal to the rear door glass inner weatherstrip.


Hide 68173B 23.INSTALL REAR DOOR GLASS INNER WEATHERSTRIP

a.
B576064

Install the rear door glass weatherstrip inner with the rear door rear belt seal and rear door front belt seal.


Hide 69283A 24.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

a.
B567833

Engage the claw to install the rear door inside handle bezel plug.


Hide 69205A 25.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B564998

Engage the guides to install the rear door inside handle sub-assembly.


Hide 67603 26.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B565028C01
0.906,1.521 1.188,1.323 true 1.188,1.042 0.938,0.854 true 0.698,0.75 0.906,0.917 0.208,0.167 10 true *1 0.719,1.531 0.938,1.708 0.219,0.177 10 true *2
*1 Rear Door Inside Locking Cable Assembly
*2 Rear Door Lock Remote Control Cable Assembly
V113147

Install in this Direction


Engage the guides to connect the rear door lock remote control cable assembly and rear door inside locking cable assembly as shown in the illustration.


b.
B576065C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws and clips to install the rear door trim board sub-assembly as shown in the illustration.


c.

Install the 3 screws.


d.
B565033

Engage the claw to close the rear door inside handle bezel plug.


Hide 27.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL

a.

Connect the connector.


b.
B576053

Engage the claws and guides to install the rear power window regulator switch assembly with rear door upper armrest base panel.


Hide 67673A 28.INSTALL REAR DOOR FRAME GARNISH

a.
B564992

Engage the claws and clip to install the rear door frame garnish.


Hide 29.CONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 30. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 31.INITIALIZE POWER WINDOW CONTROL SYSTEM