Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY › 2020.03–2020.07
RM36W0E _58 Vehicle Interior _088297 SEAT _0421671 FRONT SEAT ASSEMBLY A

SEAT  FRONT SEAT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front seat assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)

CAUTION:
B401522

·

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Wear protective gloves. Sharp areas on the parts may injure your hands.



NOTICE:

If a front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad, separate type front seatback cover and front seatback pad with cover with the necessary parts in accordance with the extent of the collision damage.


HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for the driver side and front passenger side.

·

The procedure listed below is for the driver side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch is turned off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


Hide 72123A 3.REMOVE FRONT OUTER SEAT TRACK BRACKET COVER

a.

Operate the seat track adjusting handle to move the front seat assembly to the rearmost position.


b.
B575636

Disengage the claws to remove the front outer seat track bracket cover.


Hide 72127A 4.REMOVE FRONT INNER SEAT TRACK BRACKET COVER

HINT:

Use the same procedure as for the outer side.


Hide 72137T 5.REMOVE REAR OUTER SEAT TRACK BRACKET COVER

a.

Operate the seat track adjusting handle to move the front seat assembly to the foremost position.


b.
B575637

Disengage the claws and guide to remove the rear outer seat track bracket cover.


Hide 72158E 6.REMOVE REAR INNER SEAT TRACK BRACKET COVER

a.
B575638

Disengage the claws and guide to remove the rear inner seat track bracket cover.


Hide 7.REMOVE FRONT SEAT ASSEMBLY

a.
B575485

Using a T50 "TORX" socket wrench, remove the 2 bolts on the rear side of the front seat assembly.


b.

Operate the seat track adjusting handle to move the front seat assembly to the rearmost position.


c.
B575486

Using a T50 "TORX" socket wrench, remove the 2 bolts on the front side of the front seat assembly.


d.

Operate the seat track adjusting handle to move the front seat assembly to the center position.


e.

Operate the reclining adjuster release handle and move the seatback to the upright position.


f.

Disconnect the front seat airbag assembly connector and front seat center airbag assembly connector under the front seat assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



g.

Disconnect each connector and disengage each clamp under the front seat assembly.


h.
B575487

Remove the front seat assembly as shown in the illustration.

NOTICE:
·

2 or more people are required when carrying the front seat assembly out of the vehicle.

·

Protect the front seat leg.

·

Be careful not to damage the front seat assembly, body exterior or body interior.