Home › Vehicle Interior › SEAT BELT › OCCUPANT DETECTION SENSOR (for Front Passenger Side) › 2020.03–2020.07
RM36W0E _58 Vehicle Interior _088062 SEAT BELT _0421673 OCCUPANT DETECTION SENSOR(for Front Passenger Side) A

SEAT BELT  OCCUPANT DETECTION SENSOR(for Front Passenger Side)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the occupant detection sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)

CAUTION:
B401522

·

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Wear protective gloves. Sharp areas on the parts may injure your hands.



NOTICE:

If a front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad, separate type front seatback cover and front seatback pad with cover with the necessary parts in accordance with the extent of the collision damage.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>DISASSEMBLY


HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.REMOVE FRONT SEAT ASSEMBLY

HINT:

Use the same procedure as for the driver side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>REMOVAL


Hide 71910E 2.REMOVE FRONT SEAT HEADREST ASSEMBLY

HINT:

Use the same procedure as for the driver side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>DISASSEMBLY


Hide 71074S 3.DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER

HINT:

Use the same procedure as for the driver side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>DISASSEMBLY


Hide 73230 4.REMOVE FRONT SEAT INNER BELT ASSEMBLY

Hide 72551B 5.REMOVE RECLINING HINGE COVER

HINT:

Use the same procedure as for the driver side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>DISASSEMBLY


Hide 72526 6.REMOVE RECLINING ADJUSTER RELEASE HANDLE

HINT:

Use the same procedure as for the driver side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>DISASSEMBLY


Hide 71812D 7.REMOVE FRONT SEAT CUSHION SHIELD

Hide 71862 8.REMOVE FRONT SEAT INNER CUSHION SHIELD

Hide 9.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY

HINT:

Use the same procedure as for the driver side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>DISASSEMBLY


Hide 10.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

HINT:

Use the same procedure as for the driver side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>DISASSEMBLY


Hide 71511S 11.REMOVE OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD) (for Standard Seat Type)

a.

Using a screwdriver, disengage the claws to remove the occupant detection sensor (separate type front seat cushion pad) from the separate type front seat cushion cover as shown in the illustration.

B576212C01
1.521,2.542 1.854,2.542 false 1.885,2.438 2.198,2.635 0.313,0.198 10 false *a
*a Screwdriver - -



Hide 71511S 12.REMOVE OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD) (for Sports Seat Type)

a.

Using a screwdriver, disengage the claws to remove the occupant detection sensor (separate type front seat cushion pad) from the separate type front seat cushion cover as shown in the illustration.

B578172C01
1.51,2.583 1.844,2.583 false 1.885,2.5 2.198,2.698 0.313,0.198 10 false *a
*a Screwdriver - -