Home › Engine / Hybrid System › M15A-FXE (INTAKE / EXHAUST) › EXHAUST MANIFOLD › 2020.03–2020.07
RM36W0E _51 Engine / Hybrid System _088540 M15A-FXE INTAKE / EXHAUST _0421800 EXHAUST MANIFOLD A

M15A-FXE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17168 1.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 2 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17141 2.INSTALL EXHAUST MANIFOLD

a.

Install a new exhaust manifold to head gasket to the cylinder head sub-assembly.


b.
A463773E01
1.229,0.26 1.385,0.458 0.156,0.198 10 true 1 0.573,0.521 0.729,0.719 0.156,0.198 10 true 6 1.104,0.927 1.229,1.115 0.125,0.188 10 true 5 2.073,0.958 2.198,1.146 0.125,0.188 10 true 4 2.625,0.917 2.75,1.104 0.125,0.188 10 true 2 2.729,0.271 2.854,0.458 0.125,0.188 10 true 3

Temporarily install the exhaust manifold to the cylinder head sub-assembly with 6 new nuts.


c.

Tighten the 6 nuts in the order shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


Hide 17118 3.INSTALL MANIFOLD STAY

a.
A463772E01
2.719,0.521 2.875,0.719 0.156,0.198 10 true 1 0.719,0.698 0.875,0.896 0.156,0.198 10 true 2

Temporarily install the manifold stay to the exhaust manifold and cylinder block sub-assembly with the bolt and nut.


b.

Tighten the bolt and nut in the order shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17167 4.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 58151 6.INSTALL NO. 1 FRONT FLOOR HEAT INSULATOR

a.

Install the No. 1 front floor heat insulator to the vehicle body with the nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 17410 7.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum Free Length (Front) 41.5 mm (1.63 in.)
Minimum Free Length (Rear) 38.5 mm (1.52 in.)

If the free length is less than the minimum, replace the compression spring.


b.

Temporarily install 2 new exhaust pipe gaskets to the exhaust manifold and front exhaust pipe assembly.


c.
A435170C01
2.51,1.656 2.75,1.396 false 1.823,1.115 1.51,0.708 false 1.938,2.969 2.083,2.427 false 2.792,1.292 3.104,1.49 0.313,0.198 10 false *a 1.844,2.969 2.156,3.167 0.313,0.198 10 false *2 1.302,0.615 1.615,0.813 0.313,0.198 10 false *1
*1 Exhaust Manifold or Front Exhaust Pipe Assembly
*2 Exhaust Pipe Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in each exhaust pipe gasket until its surface is flush with the exhaust manifold and front exhaust pipe assembly.

NOTICE:
·

Be sure to install the exhaust pipe gasket in the correct direction.

·

Do not reuse the exhaust pipe gaskets.

·

Do not damage the exhaust pipe gaskets.

·

Do not push in the exhaust pipe gaskets by using the exhaust pipes when connecting them.




d.

Connect the front exhaust pipe assembly to the 3 exhaust pipe supports.


e.

Install the front exhaust pipe assembly to the exhaust manifold with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C45
2.406,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.156,0.594 false 0.771,1.198 0.927,1.198 0.927,1.198 1.094,0.896 false 0.406,1.417 0.615,1.573 0.208,0.156 10 *a 0.573,0.146 0.823,0.302 0.25,0.156 10 *1 0.573,1.125 0.813,1.313 0.24,0.188 10 *2 2.698,0.083 2.927,0.26 0.229,0.177 10 *3
*1 Exhaust Manifold
*2 Front Exhaust Pipe Assembly
*3 Exhaust Pipe Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the exhaust manifold and front exhaust pipe assembly is consistent front-to-rear and left-to-right.



f.

Install the front exhaust pipe assembly to the tail exhaust pipe assembly with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C46
2.396,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.104,0.604 false 0.781,1.188 0.938,1.188 0.938,1.188 1.094,0.885 false 0.406,1.417 0.573,1.573 0.167,0.156 10 *a 0.604,0.177 0.802,0.375 0.198,0.198 10 *1 0.604,1.135 0.813,1.333 0.208,0.198 10 *2 2.719,0.115 2.885,0.271 0.167,0.156 10 *3
*1 Front Exhaust Pipe Assembly
*2 Tail Exhaust Pipe Assembly
*3 Exhaust Pipe Gasket
*a Space between Flanges: 6.5 mm (0.256 in.)


After installation, check that the space between the flanges of the front exhaust pipe assembly and tail exhaust pipe assembly is consistent front-to-rear and left-to-right.



g.

Engage the clamp.


h.

Connect the No. 2 air fuel ratio sensor connector.


Hide 51447D 9.INSTALL CENTER NO. 4 ENGINE UNDER COVER