Home › General › MAINTENANCE › P910 HYBRID TRANSAXLE FLUID › 2020.03–2020.07
RM36W0E _V1 General _088300 MAINTENANCE _0421999 P910 HYBRID TRANSAXLE FLUID A

MAINTENANCE  P910 HYBRID TRANSAXLE FLUID  REPLACEMENT  


PROCEDURE

Hide 51451A 1.REMOVE CENTER ENGINE UNDER COVER

Hide 2.REPLACE HYBRID TRANSAXLE FLUID

a.

Lift the vehicle. [#1]

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/- 1°).



b.
C429453

Using a 10 mm hexagon socket wrench, remove the filler plug and gasket from the hybrid vehicle transaxle assembly. [#2]


c.
C429454

Using a 10 mm hexagon socket wrench, remove the drain plug and gasket from the hybrid vehicle transaxle assembly and drain the hybrid transaxle fluid. [#3]


d.

Using a 10 mm hexagon socket wrench, temporarily install the drain plug and gasket to the hybrid vehicle transaxle assembly. [#4]

HINT:

Reuse the old gasket as the drain plug will be removed again.



e.
C429455C04
2.417,1.125 2.719,0.781 false 2.75,0.656 2.99,0.865 0.24,0.208 10 false *a 3.146,1.708 3.375,1.917 0.229,0.208 10 false *b
*a Filler Nozzle
*b 0 to 8 mm (0 to 0.315 in.)


Add hybrid transaxle fluid until the hybrid transaxle fluid level is between 0 to 8 mm (0 to 0.315 in.) from the bottom lip of the filler plug opening. [#5]

NOTICE:
·

Use Toyota Genuine ATF WS.

Using transmission fluid other than the above type may cause abnormal noise or vibration, or ultimately damage the transmission of your vehicle.

·

Be sure to fully insert the filler nozzle into the filler plug opening.

·

Be sure to add hybrid transaxle fluid slowly. If hybrid transaxle fluid is added quickly, the hybrid transaxle fluid may hit internal parts and bounce back, resulting in hybrid transaxle fluid coming out of the filler plug opening.

·

Be sure to directly check that the hybrid transaxle fluid level is within the specified range.

·

An insufficient or excessive amount of hybrid transaxle fluid may damage the hybrid vehicle transaxle assembly.




f.

Using a 10 mm hexagon socket wrench, temporarily install the filler plug and gasket to the hybrid vehicle transaxle assembly. [#6]

HINT:

Reuse the old gasket as the filler plug will be removed again.



g.

Lower the vehicle. [#7]


h.

Put the engine in Inspection Mode (Maintenance Mode). [#8]

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


i.

Idle the engine for 30 seconds with the ignition switch on (READY). [#9]


j.

Turn the ignition switch off. [#10]


k.

Repeat steps [#1] to [#10].


l.

Repeat steps [#1] to [#3].


m.

Using a 10 mm hexagon socket wrench, install the drain plug and a new gasket to the hybrid vehicle transaxle assembly.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


n.

Using a 10 mm hexagon socket wrench, temporarily install the filler plug and gasket to the hybrid vehicle transaxle assembly.

HINT:

Reuse the old gasket as the filler plug will be removed again.



Hide 5.INSPECT FOR HYBRID TRANSAXLE FLUID LEAK

Hide 51451A 6.INSTALL CENTER ENGINE UNDER COVER