Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2020.03–2020.07
RM36W0E _56 Audio / Visual / Telematics _088597 AUDIO / VIDEO _0422141 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  B1324  Lost Communication with Meter  B1325  Lost Communication with HUD  


DESCRIPTION

These DTCs are stored when communication between the radio and display receiver assembly and combination meter assembly or headup display (meter mirror sub-assembly)* is not possible.

*: w/ Headup Display System


DTC No. Detection Item DTC Detection Condition Trouble Area
B1324 Lost Communication with Meter CAN reception error
·

Local bus communication line

·

Combination meter power source circuit

·

Combination meter assembly

·

Radio and display receiver assembly

·

Harness or connector

·

No. 4 global can junction connector


B1325 Lost Communication with HUD CAN reception error
·

Local bus communication line

·

Headup display (meter mirror sub-assembly) power source circuit

·

Headup display (meter mirror sub-assembly)

·

Radio and display receiver assembly

·

Harness or connector

·

No. 4 global can junction connector



HINT:

The radio and display receiver assembly is the master unit.


WIRING DIAGRAM

E439849E03
2.927,2.115 4.104,2.5 1.177,0.385 10 false Combination Meter Assembly 2.917,1.958 3.365,2.25 0.448,0.292 10 false H6 3.708,1.635 4.156,1.927 0.448,0.292 10 false ES 3.073,1.073 3.521,1.365 0.448,0.292 10 false B 3.063,1.49 3.51,1.781 0.448,0.292 10 false IG+ 2.823,0.979 3.271,1.271 0.448,0.292 10 false 22 2.833,1.396 3.281,1.688 0.448,0.292 10 false 38 3.99,0.948 4.438,1.24 0.448,0.292 10 false 27 3.979,1.24 4.427,1.531 0.448,0.292 10 false 10 3.99,1.521 4.438,1.813 0.448,0.292 10 false 23 4.323,0.948 4.771,1.24 0.448,0.292 10 false 11 4.313,1.24 4.76,1.531 0.448,0.292 10 false 22 5.51,0.948 5.958,1.24 0.448,0.292 10 false 10 5.521,1.229 5.969,1.521 0.448,0.292 10 false 21 5.917,0.958 6.365,1.25 0.448,0.292 10 false 5 5.958,1.854 7.146,2.448 1.188,0.594 10 false Radio and Display Receiver Assembly 5.917,1.24 6.365,1.531 0.448,0.292 10 false 6 5.958,1.698 6.906,2.26 0.948,0.563 10 false H80 6.083,1.063 7.031,1.625 0.948,0.563 10 false CNH1 6.083,1.344 7.031,1.906 0.948,0.563 10 false CNL1 0.292,1.063 1.677,1.406 1.385,0.344 10 false from Auxiliary Battery 0.219,1.49 1.615,1.771 1.396,0.281 10 false from IGR-NO. 1 Relay 1.813,1.208 2.958,1.542 1.146,0.333 10 false ECU-DCC NO. 2 1.958,1.646 2.813,1.99 0.854,0.344 10 false METER-IGR 2.833,4.104 4.25,4.708 1.417,0.604 10 false Headup Display (Meter Mirror Sub-assembly)* 2.833,3.948 3.781,4.344 0.948,0.396 10 false H61 1.781,3.083 3.74,3.438 1.958,0.354 10 false ECU-DCC NO. 2 1.844,3.76 3.802,4.115 1.958,0.354 10 false ECU-IGR NO. 1 0.219,3.604 1.604,3.854 1.385,0.25 10 false from IGR-NO. 1 Relay 4.333,4.729 6.677,5.01 2.344,0.281 10 false No. 4 Global Can Junction Connector 4.333,4.563 6.292,4.917 1.958,0.354 10 false H115 3.083,2.938 3.531,3.229 0.448,0.292 10 false B 3.052,3.625 3.5,3.917 0.448,0.292 10 false IG 3.698,3.438 4.146,3.729 0.448,0.292 10 false ES 3.656,2.896 4.104,3.188 0.448,0.292 10 false TX+ 3.677,3.177 4.135,3.583 0.458,0.406 10 false TX- 3.969,2.781 4.417,3.073 0.448,0.292 10 false 14 3.969,3.052 4.417,3.344 0.448,0.292 10 false 15 4.385,2.781 4.833,3.073 0.448,0.292 10 false 9 4.333,3.083 4.781,3.375 0.448,0.292 10 false 20 3.979,3.344 4.427,3.635 0.448,0.292 10 false 4 2.875,2.833 3.323,3.125 0.448,0.292 10 false 2 2.875,3.51 3.323,3.802 0.448,0.292 10 false 1 1.01,5.01 3.615,5.385 2.604,0.375 10 false : Local Bus Communication Line 3.49,1.063 3.938,1.354 0.448,0.292 10 false MSCH 3.521,1.344 3.969,1.635 0.448,0.292 10 false MSCL 0.281,2.906 1.688,3.26 1.406,0.354 10 false from Auxiliary Battery 4.333,5.24 6.677,5.521 2.344,0.281 10 false *: w/ Headup Display System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK DTC
a.

Check for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTC B1324 and B1325 are not output A
DTC B1324 and B1325 are output B
DTC B1324 is output C
DTC B1325 is output D



A

B

2.CHECK LOCAL BUS

C

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE)

D

16.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) POWER SOURCE)
2.CHECK LOCAL BUS
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-10 - H115-21 Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK A
NG (Below 54 Ω) B
NG (70 Ω or higher) C



A

B

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

C

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H115 No. 4 global can junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-10 - H115-21 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

NG

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H115 No. 4 global can junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-11 - H115-22 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
5.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H115 No. 4 global can junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-9 - H115-20 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

6.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
6.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H61 headup display (meter mirror sub-assembly) connector.


c.

Connect the H115 No. 4 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H61-14 (TX+) - H61-15 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H6 combination meter assembly connector.


c.

Connect the H115 No. 4 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-27 (MSCH) - H6-10 (MSCL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H80 radio and display receiver assembly connector.


c.

Connect the H115 No. 4 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-5 (CNH1) - H80-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H80 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-5 (CNH1) - H80-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

10.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
10.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H115 No. 4 global can junction connector.


c.

Connect the H80 radio and display receiver assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-10 - H115-21 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY POWER SOURCE)
a.

Disconnect the H6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-23 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H6-22 (B) - Body ground Ignition switch off 11 to 14 V
H6-38 (IG+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H115 No. 4 global can junction connector.


c.

Connect the H6 combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-11 - H115-22 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

NG

15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
13.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H115 No. 4 global can junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-10 - H115-21 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

14.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
14.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H80 radio and display receiver assembly connector.


c.

Connect the H115 No. 4 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-5 (CNH1) - H80-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H6 combination meter assembly connector.


c.

Connect the H115 No. 4 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-27 (MSCH) - H6-10 (MSCL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) POWER SOURCE)
a.

Disconnect the H61 headup display (meter mirror sub-assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H61-4 (ES) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H61-2 (B) - Body ground Ignition switch off 11 to 14 V
H61-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H115 No. 4 global can junction connector.


c.

Connect the H61 headup display (meter mirror sub-assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-9 - H115-20 Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

NG

20.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
18.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H115 No. 4 global can junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H115-10 - H115-21 Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

19.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
19.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H80 radio and display receiver assembly connector.


c.

Connect the H115 No. 4 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-5 (CNH1) - H80-6 (CNL1) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H61 headup display (meter mirror sub-assembly) connector.


c.

Connect the H115 No. 4 global can junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H61-14 (TX+) - H61-15 (TX-) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE HEADUP DISPLAY (METER MIRROR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR