Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › THROTTLE BODY
RM36W0E _51 Engine / Hybrid System _087500 M15A-FXE ENGINE CONTROL _0422219 THROTTLE BODY A

M15A-FXE ENGINE CONTROL  THROTTLE BODY  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 22271 1.INSTALL THROTTLE BODY GASKET

a.
A463100C01
1.615,0.594 1.927,0.49 true 1.969,0.354 2.229,0.563 0.26,0.208 10 true *a
*a Protrusion


Install a new throttle body gasket to the intake manifold with the protrusion of the throttle body gasket oriented as shown in the illustration.


Hide 22030 2.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A463101

Using an 8 mm socket wrench, install the throttle body with motor assembly to the intake manifold with the 3 bolts.

NOTICE:

If the throttle body with motor assembly has been struck or dropped, replace it.


Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the throttle body with motor assembly connector.


c.
A463036C01
0.677,3.042 0.99,2.771 true 0.771,2.24 1.083,2.438 0.313,0.198 10 false *a 0.51,3.01 0.823,3.208 0.313,0.198 10 false *d 1.323,2.948 1.635,3.146 0.313,0.198 10 false *c 1.417,2.677 1.729,2.875 0.313,0.198 10 false *b 1.313,2.438 1.625,2.635 0.313,0.198 10 false *c
*a Top of Vehicle
*b Left of Vehicle
*c 45°(Claw of Clip Location)
*d Paint Mark


Connect the No. 5 water by-pass hose to the throttle body with motor assembly and slide the clip to secure it.

NOTICE:

Make sure to position the clip as shown in the illustration.



d.
A463037C01
2.708,3.073 2.49,2.781 true 2.229,2.229 2.542,2.427 0.313,0.198 10 false *a 2.51,2.25 2.823,2.448 0.313,0.198 10 false *c 2.938,2.792 3.25,2.99 0.313,0.198 10 false *b 2.844,2.583 3.156,2.781 0.313,0.198 10 false *c 2.74,3 3.052,3.198 0.313,0.198 10 false *d
*a Top of Vehicle
*b Left of Vehicle
*c 45°(Claw of Clip Location)
*d Paint Mark


Connect the No. 8 water by-pass hose to the throttle body with motor assembly and slide the clip to secure it.

NOTICE:

Make sure to position the clip as shown in the illustration.



Hide 17881 3.INSTALL NO. 1 AIR CLEANER HOSE

a.
A463884C01
0.438,0.854 0.781,0.333 true 0.917,1.208 1.042,0.99 false 2.365,0.708 2.49,0.49 true 2.531,1.229 2.792,0.802 true 1.521,1.938 1.719,1.802 true 0.344,2.865 0.646,2.646 true 2.146,3.25 2.448,3.031 true 0.823,0.229 1.031,0.427 0.208,0.198 10 false *a 0.792,1.177 1,1.375 0.208,0.198 10 false *b 2.521,0.354 2.729,0.552 0.208,0.198 10 true *b 2.375,1.167 2.583,1.365 0.208,0.198 10 false *a 1.76,1.708 1.948,1.885 0.188,0.177 10 true *1 0.146,2.833 0.333,3.01 0.188,0.177 10 true *2 1.927,3.188 2.115,3.365 0.188,0.177 10 true *2 1.948,4.042 2.156,4.24 0.208,0.198 10 false *d 2.5,3.5 2.708,3.698 0.208,0.198 10 false *c 0.74,3.479 0.948,3.677 0.208,0.198 10 false *c 1.292,4.083 1.5,4.281 0.208,0.198 10 false *d
*1 No. 2 Ventilation Hose
*2 Hose Clip
*a Protrusion
*b Cutout
*c Top of Vehicle
*d Front of Vehicle


Install the No. 1 air cleaner hose to the throttle body with motor assembly and tighten the hose clamp.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)

NOTICE:

Align the cutout of the air cleaner hose with the protrusion of the throttle body with motor assembly as shown in the illustration.



b.
A463883C01
0.865,0.781 0.427,0.406 true 0.219,0.333 0.406,0.531 0.188,0.198 10 true *1 2.417,0.188 2.604,0.385 0.188,0.198 10 false *a 3.073,0.344 3.26,0.542 0.188,0.198 10 false *c 3.083,0.906 3.271,1.104 0.188,0.198 10 false *c 3.177,0.625 3.365,0.823 0.188,0.198 10 false *b
*1 Hose Clamp
*a Top of Vehicle
*b Front of Vehicle
*c 45°(Claw of Clip Location)


Connect the No. 2 ventilation hose to the cylinder head cover sub-assembly and slide the hose clip to secure it.

NOTICE:

Make sure to position the clip as shown in the illustration.



Hide 51451A 6.INSTALL CENTER ENGINE UNDER COVER

Hide 7.PERFORM INITIALIZATION

NOTICE:
·

Be sure to perform this procedure after removing and reinstalling the throttle body with motor assembly or any throttle body with motor assembly components.

·

Perform the following procedure after replacing the throttle body with motor assembly or any throttle body with motor assembly components. The following procedure should also be performed if the throttle body with motor assembly is cleaned.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

f.

Start the engine and check that the MIL is not illuminated. After the engine is warmed up, check that the idle speed is within the specified range with the A/C switch off.

Standard Idle Speed:

950 to 1050 rpm


NOTICE:
·

Be sure to perform this step with all accessories off.

·

Make sure that the shift lever is in P or N.




g.

Enter the following menus: Powertrain / Engine / Data List / Throttle Position Sensor No.1 Voltage %.

Powertrain > Engine > Data List
Tester Display
Throttle Position Sensor No.1 Voltage %
50003 372 216

h.

According to the display on the GTS, read the Data List while fully depressing the accelerator pedal and check that the value is 60% or higher.


i.

Perform a road test and confirm that there are no abnormalities.