Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS › 2020.03–2020.09
RM36W0E _59 Vehicle Exterior _088018 WINDOW / GLASS _0424524 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  INSTALLATION  


PROCEDURE

Hide 68131 1.CLEAN BACK DOOR GLASS

a.

When reusing the back door glass:

i.
B106929

Using a scraper, remove any remaining adhesive residue from the back window glass.

NOTICE:

Be careful not to damage the back door glass.




b.

Clean the outer circumference of the back door glass with a non-residue solvent.

NOTICE:
·

Do not touch the back window glass surface after cleaning it.

·

Even if using a new back door glass, clean it with a non-residue solvent.




Hide 62785F 2.INSTALL BACK DOOR GLASS SPACER

a.

Using a brush or sponge, coat the installation area of the 2 back door glass spacers with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.

Install 2 new back door glass spacers to the back door glass as shown in the illustration.

B563201C02
1.073,1.135 1.25,0.917 1.25,0.917 1.167,0.594 false 0.865,1.083 0.74,0.781 0.74,0.781 0.948,0.542 false 6.125,1.115 5.896,0.865 5.896,0.865 6.021,0.573 false 6.302,1.094 6.417,0.823 6.417,0.823 6.219,0.563 false 1.802,0.042 2.115,0.198 0.313,0.156 10 false *a 0.542,0.708 0.854,0.865 0.313,0.156 10 false *b 1.313,0.865 1.625,1.021 0.313,0.156 10 false *b 5.719,0.792 6.031,0.948 0.313,0.156 10 false *b 6.479,0.76 6.792,0.917 0.313,0.156 10 false *b
*a Back Side of Back Door Glass *b Ceramic Notch



Hide 64828B 3.INSTALL BACK WINDOW GLASS CLIP LH

a.

Using a brush or sponge, coat the installation area of the back window glass clip LH with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B563199C03
0.094,0.083 0.406,0.281 0.313,0.198 10 false *a
*a Back Side of Back Door Glass
V100155

Adhesive Tape


Install a new back window glass clip LH to the back door glass as shown in the illustration.


c.

Remove the adhesive tape.


Hide 64827B 4.INSTALL BACK WINDOW GLASS CLIP RH

HINT:

Use the same procedure as for the LH side.


Hide 75574C 5.INSTALL NO. 1 BACK WINDOW OUTSIDE MOULDING LH

a.

Using a brush or sponge, coat the installation area of the No. 1 back window outside moulding LH with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.

Install a new back window outside moulding LH to the back door glass as shown in the illustration.

B563202C02
5.24,0.771 5.063,0.5 true 5.531,2.458 5.24,2.313 true 0.344,0.438 0.656,0.594 0.313,0.156 10 false *a 5.563,2.417 5.875,2.573 0.313,0.156 10 false *b 4.896,0.365 5.208,0.521 0.313,0.156 10 false *b 5.865,0.448 6.177,0.604 0.313,0.156 10 false a 5.917,0.719 6.229,0.875 0.313,0.156 10 false a 5.656,1.698 5.969,1.854 0.313,0.156 10 false b 5.813,1.896 6.125,2.052 0.313,0.156 10 false c
*a Back Side of Back Door Glass *b Ceramic Notch


Standard Dimension:
Area Dimension
a 0 to 3.0 mm (0 to 0.118 in.)
b 0 to 2.0 mm (0 to 0.0787 in.)
c 0 to 1.0 mm (0 to 0.0394 in.)



Hide 75573G 6.INSTALL NO. 1 BACK WINDOW OUTSIDE MOULDING RH

HINT:

Use the same procedure as for the LH side.


Hide 64813B 7.INSTALL BACK WINDOW GLASS ADHESIVE DAM

a.

Using a brush or sponge, coat the installation area of the back window glass adhesive dam with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.

Install a new back window glass adhesive dam to the back door glass as shown in the illustration.

B563203C02
0.677,0.865 0.844,0.76 true 6.302,0.76 6.49,0.865 true 2.094,0.833 2.406,0.99 0.313,0.156 10 false *a 0.438,0.885 0.625,1.031 0.188,0.146 10 true *b 6.531,0.896 6.719,1.042 0.188,0.146 10 true *b
*a Back Side of Back Door Glass *b Ceramic Notch



Hide 64813B 8.INSTALL NO. 2 BACK WINDOW GLASS ADHESIVE DAM

a.

Using a brush or sponge, coat the installation area of the No. 2 back window glass adhesive dam with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.

Install a new No. 2 back window glass adhesive dam to the back door glass as shown in the illustration.

B563204C02
2.125,2.073 2.458,2.01 true 3.25,1.958 3.542,2.073 true 4.74,1.958 5.042,2.073 true 1.427,0.073 1.74,0.229 0.313,0.156 10 false *a 2.521,1.906 2.719,2.063 0.198,0.156 10 true *b 3.031,1.854 3.229,2.01 0.198,0.156 10 true *b 4.5,1.865 4.698,2.021 0.198,0.156 10 true *b
*a Back Side of Back Door Glass *b Ceramic Notch



Hide 68131 9.INSTALL BACK DOOR GLASS

a.

Clean and shape the contact surface of the vehicle body.

i.
B153152C19
0,0 0,0 false
V100155

Adhesive


Using a knife, cut away excess adhesive on the contact surface of the vehicle body as shown in the illustration.

NOTICE:

Leave as much adhesive on the vehicle body as possible.




b.

Back door glass preliminary installation procedures:

i.

Install the suction cups to the back door glass.


ii.

Temporarily place the back door glass onto the vehicle body and set it so that the gap between the body and upper portion and sides of the back door glass is even.



c.

Position the back door glass.

i.

Using suction cups, place the back door glass in the correct position.


ii.

Check that the whole contact surface of the back door glass rim is perfectly even.


iii.
B563205C03
1.333,0.521 1.313,0.958 1.313,0.958 1.51,0.813 true 1.219,1 1.448,1.188 0.229,0.188 10 true *a
*a Matchmark
V100155

Protective Tape


Align the matchmarks on the back door glass and back door panel.

NOTICE:

Check that the back window glass clip LH and back window glass clip RH are engaged to the back door panel correctly.



iv.

Remove the back door glass.



d.

Using a brush, coat the installation surfaces on the back door panel with primer M.

NOTICE:
·

Do not coat the adhesive with primer M.

·

Do not apply too much primer M.

·

Allow the primer M to dry for 3 minutes or more.

·

Throw away any leftover primer M.



HINT:

If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.



e.

Using a brush or sponge, coat the adhesive application area with primer G.

B563206C02
6.094,2.042 6.302,2 false 5.271,0.938 5.5,1.021 false 5.094,0.865 5.406,1.021 0.313,0.156 10 false *1 6.365,1.927 6.677,2.083 0.313,0.156 10 false *2 0.531,0.854 0.844,1.01 0.313,0.156 10 false *a 1.896,2.354 2.052,2.51 0.156,0.156 10 true B 1.927,1.125 2.083,1.281 0.156,0.156 10 false A 1.917,1.448 2.073,1.604 0.156,0.156 10 true A 1.906,2.708 2.063,2.865 0.156,0.156 10 false B 0.573,1.219 0.729,1.375 0.156,0.156 10 false C 0.906,1.302 1.063,1.458 0.156,0.156 10 true C 4.74,0.406 5.052,0.563 0.313,0.156 10 false A-A 4.792,1.521 5.104,1.677 0.313,0.156 10 false B-B 4.24,2.51 4.552,2.667 0.313,0.156 10 false C-C 5.948,3.521 6.104,3.677 0.156,0.156 10 false c 5.76,1.531 5.917,1.688 0.156,0.156 10 false b 5.74,0.51 5.896,0.667 0.156,0.156 10 false a
*1 Back Window Glass Adhesive Dam *2 No. 2 Back Window Glass Adhesive Dam
*a Back Side of Back Door Glass - -
V100155

Primer G - -


Standard Dimension:
Area Dimension
a 11 mm (0.433 in.) or more
b 11 mm (0.433 in.) or more
c 44.4 mm (1.75 in.)


NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



f.

Apply adhesive to the back door glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent


i.
B214800C28
1.198,0.438 1.385,0.5 false 0.5,0.625 0.656,0.823 0.156,0.198 10 false a 1.344,1.365 1.5,1.563 0.156,0.198 10 false a 1.115,0.885 1.271,1.083 0.156,0.198 10 false b 0.76,1 0.917,1.198 0.156,0.198 10 false b 1.406,0.438 1.646,0.615 0.24,0.177 10 false *a
*a Nozzle
V100155

Adhesive


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 12 to 15 mm (0.472 to 0.591 in.)
b 8.0 to 11 mm (0.315 to 0.433 in.)




g.

Load the sealer gun with the cartridge.


h.

Apply adhesive to the back door glass as shown in the illustration.

B563207C02
5.406,0.802 5.635,0.875 false 6.063,2.052 6.219,1.958 false 5.229,0.719 5.542,0.875 0.313,0.156 10 false *1 6.271,1.865 6.583,2.021 0.313,0.156 10 false *2 0.521,0.729 0.833,0.885 0.313,0.156 10 false *a 1.927,1.104 2.083,1.26 0.156,0.156 10 false A 1.875,1.448 2.031,1.604 0.156,0.156 10 true A 1.906,2.719 2.063,2.875 0.156,0.156 10 false B 1.896,2.354 2.052,2.51 0.156,0.156 10 true B 0.917,1.302 1.073,1.469 0.156,0.167 10 true C 0.563,1.188 0.719,1.344 0.156,0.156 10 false C 4.458,0.156 4.781,0.323 0.323,0.167 10 false A-A 5.042,1.333 5.365,1.5 0.323,0.167 10 false B-B 4.156,2.448 4.479,2.615 0.323,0.167 10 false C-C 5.385,0.25 5.542,0.406 0.156,0.156 10 false a 6.083,1.365 6.24,1.521 0.156,0.156 10 false b 5.896,3.531 6.052,3.688 0.156,0.156 10 false c
*1 Back Window Glass Adhesive Dam *2 No. 2 Back Window Glass Adhesive Dam
*a Back Side of Back Door Glass - -
V100155

Adhesive - -


Standard Dimension:
Area Dimension
a 23.5 mm (0.925 in.)
b 21.2 mm (0.835 in.)
c 51.4 mm (2.02 in.)



i.

Install the back door glass.

i.
B563205C04
1.313,0.5 1.344,0.917 1.344,0.917 1.5,0.792 true 1.271,0.979 1.5,1.167 0.229,0.188 10 true *a
*a Matchmark


Using suction cups, position the back door glass so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the back window glass clip LH and back window glass clip RH are engaged to the back door panel correctly.

·

Check the clearance between the back door panel and back door glass.




ii.

Lightly press the outer surface of the back door glass to ensure a close fit and engage the back window glass clip LH and back window glass clip RH.

HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.




j.

Using a scraper, remove any excess or protruding adhesive.


k.

Hold the back door glass using protective tape until the applied adhesive becomes hard.

HINT:

Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.



l.

Connect each connector and engage each clamp.


Hide 10.INSTALL REAR SPOILER ASSEMBLY (w/ Rear Spoiler)

Hide 85110R 12.INSTALL REAR WIPER MOTOR ASSEMBLY

Hide 76811B 13.INSTALL LUGGAGE COMPARTMENT DOOR OUTSIDE GARNISH

Hide 14.INSPECT FOR LEAK

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.