Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV RELAY ASSEMBLY
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0424593 HV RELAY ASSEMBLY A

HYBRID / BATTERY CONTROL  HV RELAY ASSEMBLY  INSTALLATION  


PROCEDURE

Hide G3850 1.INSTALL NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Install the No. 1 traction battery device box assembly to the No. 1 hybrid battery shield sub-assembly with the 4 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

NOTICE:

If the No. 1 traction battery device box assembly has been struck or dropped, replace it with a new one.



b.

Engage the claw to install the wiring harness protector.


c.

Connect the 2 No. 1 traction battery device box assembly connectors.

NOTICE:

Make sure that the connectors are connected securely.



d.

Install the electric vehicle battery plug assembly to the HV battery with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


e.

Connect the hybrid battery terminal block connector.

NOTICE:

Make sure that the connector is connected securely.



f.

Connect the No. 1 traction battery device box assembly connector.

NOTICE:

Make sure that the connector is connected securely.



g.

Engage the claw to close the wiring harness protector.


Hide G920NB 2.INSTALL UPPER HV BATTERY COVER SUB-ASSEMBLY

Hide 821H1 4.CONNECT HV FLOOR UNDER WIRE

Hide G92N1 5.INSTALL HV BATTERY UPPER COVER PANEL

Hide 71033 6.INSTALL REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide 72693 8.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 9.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 73350C 10.CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 12. PERFORM CURRENT SENSOR OFFSET LEARNING

HINT:

Perform this procedure when the No. 1 traction battery device box assembly or battery ECU assembly has been replaced.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch on (READY).


c.

Perform a road test.

NOTICE:

Accelerate and decelerate gently. Avoid rapid acceleration and deceleration.


i.

Enter the following menus: Powertrain / HV Battery / Data List / Hybrid Battery Current.

Powertrain > HV Battery > Data List
Tester Display
Hybrid/EV Battery Current
50003 398 289

ii.

Drive the vehicle with the value of Data List item "Hybrid Battery Current" between -50 A and 50 A.

HINT:

Distance and driving time are not specified.



iii.

Turn the ignition switch off and leave the vehicle for 30 seconds or more.


iv.

Turn the ignition switch on (IG).


v.

Enter the following menus: Powertrain / HV Battery / Data List / Hybrid Battery Current.

Powertrain > HV Battery > Data List
Tester Display
Hybrid/EV Battery Current
50003 398 289

vi.

Check that the value of "Hybrid Battery Current" is between -0.5 A and 0.5 A with the ignition switch on (IG).

NOTICE:

If the value is outside the specified range, perform the road test again.


HINT:
·

When the ignition switch is on (IG), if value of "Hybrid Battery Current" is between -0.5 A and 0.5 A, current sensor offset learning has been completed.

·

Even if the current sensor offset learning is not complete, the current sensor value will be corrected by repeating the road test a maximum of 7 times.