When working near the engine room while the engine has started or the power source mode is engine switch on (IG), do not touch the fan and generator V belt or rotating components such as the fan, etc.
Touching the fan and generator V belt or rotating components such as the fan, etc. could result in your hand or clothing getting caught and pulled in.
1.INSPECT ENGINE COOLANT
2.INSPECT ENGINE OIL
3.INSPECT AUXILIARY BATTERY CONDITION
19100P
4.INSPECT SPARK PLUG
17801
5.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Remove the air cleaner filter element sub-assembly.
Click hereGeneral>MAINTENANCE>M15A-FKS AIR CLEANER FILTER ELEMENT>REMOVAL
Visually check that the air cleaner filter element sub-assembly is not damaged or excessively oily. If necessary, replace the air cleaner filter element sub-assembly.
If there is any dirt or clogs in the air cleaner filter element sub-assembly, clean it with compressed air.
If any dirt or clogs remain even after cleaning the air cleaner filter element sub-assembly with compressed air, replace it.
Install the air cleaner filter element sub-assembly.
Click hereGeneral>MAINTENANCE>M15A-FKS AIR CLEANER FILTER ELEMENT>INSTALLATION
16361A
6.INSPECT FAN AND GENERATOR V BELT
16620D
7.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY
Remove the fan and generator V belt.
Turn the V-ribbed belt tensioner assembly clockwise and counterclockwise and check that it turns smoothly and does not catch.
If the V-ribbed belt tensioner assembly does not turn smoothly or catches, replace the V-ribbed belt tensioner assembly.
Install the fan and generator V belt.
Click hereGeneral>MAINTENANCE>M15A-FKS DRIVE BELT>INSTALLATION
13750
8.INSPECT VALVE LASH ADJUSTER ASSEMBLY NOISE
Rev up the engine several times. Check that the engine does not emit unusual noises.
If unusual noises occur, warm up the engine and idle it for 30 minutes or more, then perform the inspection.
If any defects or problems are found during the inspection, perform the valve lash adjuster assembly inspection.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION
9.INSPECT IGNITION TIMING
Check the ignition timing with the cooling fan off.
Turn off all electrical systems and the A/C.
When checking the ignition timing, the transaxle should be in neutral or park.
Warm up and stop the engine.
Connect the GTS to the DLC3.
Start the engine and run it at idle.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Ignition Timing Cylinder #1.
| Tester Display |
|---|
| Ignition Timing Cylinder #1 |
| Condition | Specified Condition |
|---|---|
| Idle speed | -5 to 15°CA BTDC |
Enter the following menus: Powertrain / Engine / Active Test / Activate the TC Terminal / ON.
| Active Test Display |
|---|
| Activate the TC Terminal |
| Data List Display |
|---|
| Ignition Timing Cylinder #1 |
Monitor Ignition Timing Cylinder #1 of the Data List.
| Condition | Specified Condition |
|---|---|
| Idle speed | 8 to 12°CA BTDC |
Enter the following menus: Powertrain / Engine / Active Test / Activate the TC Terminal / OFF.
Check that the ignition timing advances immediately when the engine speed is increased.
10.INSPECT ENGINE IDLE SPEED
Check the ignition timing with the cooling fan off.
Turn off all electrical systems and the A/C.
When checking the ignition timing, the transaxle should be in neutral or park.
Warm up and stop the engine.
Connect the GTS to the DLC3.
Start the engine and run it at idle.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Engine Speed.
| Tester Display |
|---|
| Engine Speed |
Read the value displayed on the tester.
| Condition | Specified Condition |
|---|---|
| P Position | 790 to 890 rpm |
| Condition | Specified Condition |
|---|---|
| P Position | 830 to 930 rpm |
11.INSPECT COMPRESSION
Keep the spark plug holes free of foreign matter when measuring the compression pressure.
Warm up and stop the engine.
Check for DTCs.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
Remove the 3 spark plugs.
Disconnect the No. 6 engine wire connector.
Check the cylinder compression pressure.
Insert a compression gauge into the spark plug hole.
Fully open the throttle.
While cranking the engine, measure the compression pressure.
| Item | Minimum Compression Pressure | Standard Compression Pressure |
|---|---|---|
| No.1 Cylinder | 1300 kPa
13.3 kgf/cm2 189 psi |
1500 kPa
15.3 kgf/cm2 218 psi |
| No.2 Cylinder | 1300 kPa
13.3 kgf/cm2 189 psi |
1500 kPa
15.3 kgf/cm2 218 psi |
| No.3 Cylinder | 1300 kPa
13.3 kgf/cm2 189 psi |
1500 kPa
15.3 kgf/cm2 218 psi |
| Pressure Difference between Each Cylinder | - | 200 kPa or less
2.0 kgf/cm2 or less 29 psi or less |
Always use a fully charged auxiliary battery to obtain an engine speed of 250 rpm or more.
Inspect all cylinders in the same way.
Measure the compression pressure as quickly as possible.
If the cylinder compression pressure is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect it again.
If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.
If the compression pressure stays low, a valve may be stuck or seated improperly, or there may be leaks in the cylinder head gasket.
Connect the No. 6 engine wire connector.
Install the 3 spark plugs.
Click hereGeneral>MAINTENANCE>M15A-FKS SPARK PLUG>INSTALLATION
Clear the DTCs.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
After the inspection, clear the DTCs, check for DTCs again and make sure the normal system code is output.
12.INSPECT CO/HC
This check determines whether or not the idle CO/HC complies with regulations.
Start the engine.
Run the engine at 2500 rpm for approximately 180 seconds.
Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idle.
Immediately check the CO/HC concentration during idle and when the engine is running at 2500 rpm.
When performing a 2 mode (with the engine idling/running at 2500 rpm) test, the measurement procedures are determined by applicable local regulations.
If the CO/HC concentration does not comply with the regulations, perform troubleshooting in the order given below.
Check for DTCs.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
See the following table for possible causes, then inspect the applicable parts and repair them if necessary.
| CO | HC | Problem | Cause |
|---|---|---|---|
| Normal | High | Rough idle | 1.
Faulty ignition: -
Incorrect valve timing -
Fouled, shorted or improperly gapped spark plugs 2.
Incorrect valve clearance (valve lash adjuster assembly) 3.
Leaks in intake or exhaust valves 4.
Leaks in cylinders |
| Low | High | Rough idle (Fluctuating HC reading) | 1.
Vacuum leaks: -
PCV hoses -
Intake manifold -
Throttle body with motor assembly 2.
Lean mixture causing misfire |
| High | High | Rough idle (Black smoke from exhaust) | 1.
Restricted air cleaner filter element sub-assembly 2.
Plugged PCV valve 3.
Faulty SFI systems: -
Fuel pressure regulator assembly -
Engine coolant temperature sensor -
Mass air flow meter -
ECM -
Fuel injector assemblies -
Throttle position sensor (built into throttle body with motor assembly) |