13801
1.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Turn the roller by hand to check that it turns smoothly.
If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.
13750
2.INSPECT VALVE LASH ADJUSTER ASSEMBLY
Keep the valve lash adjuster assembly free from dirt and foreign matter.
Only use clean engine oil.
Place the valve lash adjuster assembly into a container filled with engine oil.
Insert the tip of SST into the valve lash adjuster assembly plunger and use the tip to press down on the check ball inside the plunger.
| *a | Correct | *b | Incorrect |
| *c | Tapered Path | *d | Low Pressure Chamber |
| *e | High Pressure Chamber | *f | Plunger |
| *g | Check Ball | - | - |
Squeeze SST and the valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.
Check the movement of the plunger and bleed the air.
Plunger moves up and down.
When bleeding air from the high-pressure chamber, make sure that the tip of SST is pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.
After bleeding the air, remove SST. Then try to quickly and firmly press the plunger by hand.
The plunger is very difficult to move.
If the plunger is easy to move, replace the valve lash adjuster assembly.
13501A
3.INSPECT INTAKE CAMSHAFT SUB-ASSEMBLY
Inspect the intake camshaft sub-assembly for runout.
Place the intake camshaft sub-assembly on V-blocks.
Using a dial indicator, measure the runout at the center journal.
0.03 mm (0.00118 in.)
If the runout is more than the maximum, replace the intake camshaft sub-assembly.
Check the intake camshaft sub-assembly oil clearance after replacing the intake camshaft sub-assembly.
Inspect the cam lobes.
Using a micrometer, measure the cam lobe height.
42.616 to 42.716 mm (1.678 to 1.682 in.)
42.506 mm (1.673 in.)
If the cam lobe height is less than the minimum, replace the intake camshaft sub-assembly.
Inspect the intake camshaft sub-assembly journals.
Using a micrometer, measure the journal diameter.
| Item | Specified Condition |
|---|---|
| No. 1 journal | 33.984 to 34.000 mm (1.33795 to 1.33858 in.) |
| Other journals | 23.959 to 23.975 mm (0.94326 to 0.94389 in.) |
If the journal diameter is not as specified, check the intake camshaft sub-assembly oil clearance.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION
13502B
4.INSPECT EXHAUST CAMSHAFT SUB-ASSEMBLY
Inspect the exhaust camshaft sub-assembly for runout.
Place the exhaust camshaft sub-assembly on V-blocks.
Using a dial indicator, measure the runout at the center journal.
0.03 mm (0.00118 in.)
If the runout is more than the maximum, replace the exhaust camshaft sub-assembly.
Check the camshaft oil clearance after replacing the exhaust camshaft sub-assembly.
Inspect the cam lobes.
Using a micrometer, measure the cam lobe height.
| Item | Specified Condition |
|---|---|
| Exhaust camshaft sub-assembly | 41.990 to 42.090 mm (1.653 to 1.657 in.) |
| Exhaust camshaft sub-assembly (for Fuel Pump) | 39.550 to 39.650 mm (1.557 to 1.561 in.) |
| Item | Specified Condition |
|---|---|
| Exhaust camshaft sub-assembly | 41.880 mm (1.649 in.) |
| Exhaust camshaft sub-assembly (for Fuel Pump) | 39.450 mm (1.553 in.) |
If the cam lobe height is less than the minimum, replace the exhaust camshaft sub-assembly.
Inspect the exhaust camshaft sub-assembly journals.
Using a micrometer, measure the journal diameter.
| Item | Specified Condition |
|---|---|
| No. 1 journal | 40.984 to 41.000 mm (1.61354 to 1.61417 in.) |
| Other journals | 23.959 to 23.975 mm (0.94326 to 0.94389 in.) |
If the journal diameter is not as specified, check the camshaft oil clearance.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION
5.INSPECT CAMSHAFT OIL CLEARANCE
Clean the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, 2 No. 3 camshaft bearing caps, camshaft housing sub-assembly and camshaft journals.
Place the intake camshaft sub-assembly and exhaust camshaft sub-assembly on the camshaft housing sub-assembly.
| *a | Plastigage |
Lay a strip of Plastigage across each of the camshaft journals.
Install the camshaft bearing caps.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE MECHANICAL)>ENGINE UNIT>REASSEMBLY
Do not turn the camshafts.
Remove the camshaft bearing caps.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY
| *a | Plastigage |
| *b | No. 1 Journal |
| *c | Other Journal |
Measure the Plastigage at its widest point.
| Item | Specified Condition |
|---|---|
| No. 1 journal | 0.035 to 0.072 mm (0.00138 to 0.00283 in.) |
| Other journals | 0.025 to 0.062 mm (0.00098 to 0.00244 in.) |
| Item | Specified Condition |
|---|---|
| No. 1 journal | 0.027 to 0.064 mm (0.00106 to 0.00252 in.) |
| Other journals | 0.025 to 0.062 mm (0.00098 to 0.00244 in.) |
| Item | Specified Condition |
|---|---|
| No. 1 journal | 0.085 mm (0.00335 in.) |
| Other journals | 0.085 mm (0.00335 in.) |
| Item | Specified Condition |
|---|---|
| No. 1 journal | 0.085 mm (0.00335 in.) |
| Other journals | 0.085 mm (0.00335 in.) |
Completely remove the Plastigage after the inspection.
If the oil clearance is more than the maximum, replace the intake camshaft sub-assembly or exhaust camshaft sub-assembly. If necessary, replace the camshaft housing sub-assembly.
13506
6.INSPECT CHAIN SUB-ASSEMBLY
| *a | Measurement Length |
Using a spring scale, pull the chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.
Using a vernier caliper, measure the length of 15 links.
116.30 mm (4.58 in.)
Perform the measurement at 3 random places. Use the average of the measurements.
If the average elongation is more than the maximum, replace the chain sub-assembly.
13050
7.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
Place the chain sub-assembly around the camshaft timing gear assembly.
Using a vernier caliper, measure the diameter of the camshaft timing gear assembly and chain sub-assembly.
100.01 mm (3.94 in.)
The vernier caliper must be in contact with the chain rollers when measuring.
If the diameter is less than the minimum, replace the chain sub-assembly and camshaft timing gear assembly.
13070A
8.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
Place the chain sub-assembly around the camshaft timing exhaust gear assembly.
Using a vernier caliper, measure the diameter of the camshaft timing exhaust gear assembly and chain sub-assembly.
100.01 mm (3.94 in.)
The vernier caliper must be in contact with the chain rollers when measuring.
If the diameter is less than the minimum, replace the chain sub-assembly and camshaft timing exhaust gear assembly.
13521
9.INSPECT CRANKSHAFT TIMING SPROCKET
Place the chain sub-assembly around the crankshaft timing sprocket.
Using a vernier caliper, measure the diameter of the crankshaft timing sprocket and chain sub-assembly.
51.35 mm (2.02 in.)
The vernier caliper must be in contact with the chain rollers when measuring.
If the diameter is less than the minimum, replace the chain sub-assembly and crankshaft timing sprocket.
13540
10.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY
| *a | Plunger |
Push the plunger and check that it moves smoothly.
If the plunger does not move smoothly, replace the No. 1 chain tensioner assembly.
13559
11.INSPECT CHAIN TENSIONER SLIPPER
| *a | Depth |
Using a vernier caliper, measure the wear depth of the chain tensioner slipper.
1.0 mm (0.0394 in.)
If the depth is more than the maximum, replace the chain tensioner slipper.
13561
12.INSPECT NO. 1 CHAIN VIBRATION DAMPER
| *a | Depth |
Using a vernier caliper, measure the wear depth of the No. 1 chain vibration damper.
1.0 mm (0.0394 in.)
If the depth is more than the maximum, replace the No. 1 chain vibration damper.
11101A
13.INSPECT CYLINDER HEAD SET BOLT
for 140 mm cylinder head set bolt:
| *a | Measurement Point |
| *b | 105 mm (4.134 in.) |
Using a vernier caliper, measure the diameter of the threads at the measurement point.
10.7 to 10.9 mm (0.421 to 0.429 in.)
10.6 mm (0.417 in.)
105 mm (4.134 in.)
If the diameter is less than the minimum, replace the cylinder head set bolt with a new one. Failure to do so may lead to engine damage.
If there is any thread deformation, replace the cylinder head set bolt with a new one.
for 130 mm cylinder head set bolt:
| *a | Measurement Point |
| *b | 115 mm (4.528 in.) |
Using a vernier caliper, measure the diameter of the threads at the measurement point.
9.7 to 9.9 mm (0.382 to 0.390 in.)
9.6 mm (0.378 in.)
115 mm (4.528 in.)
If the diameter is less than the minimum, replace the cylinder head set bolt with a new one. Failure to do so may lead to engine damage.
If there is any thread deformation, replace the cylinder head set bolt with a new one.