Home › Engine / Hybrid System › M15A-FKS (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL › 2020.03–2020.07
RM36W0E _51 Engine / Hybrid System _087837 M15A-FKS ENGINE MECHANICAL _0424628 REAR CRANKSHAFT OIL SEAL A

M15A-FKS ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear engine oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Air leaks from intake system is repaired

·

Gas leaks from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Front wheel alignment adjustment Calibration
·

VSC disabled or malfunctions

·

DTCs are stored

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 30400 1.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (for CVT)

Hide 31250 2.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transaxle)

Hide 32101B 3.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly level.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.
A464394

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


c.
A466563

Remove the 8 bolts, rear drive plate spacer, drive plate and ring gear sub-assembly.


Hide 13405 4.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

a.

Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly level.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.
A464394

Using SST, hold the crankshaft pulley assembly.

SST
09213-54015  
09330-00021  


c.
A466564

Remove the 8 bolts, rear drive plate spacer, drive plate and ring gear sub-assembly.


Hide 19315 5.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A464827

Remove the No. 1 crankshaft position sensor plate.


Hide 11401L 6.REMOVE REAR ENGINE OIL SEAL

a.
A464828C02
2.99,1.458 3.177,0.771 true 1.813,1.458 1.542,1.135 true 2.917,1.49 3.229,1.688 0.313,0.198 10 false *b 1.833,1.5 2.052,1.698 0.219,0.198 10 true *a
*a Protective Tape
*b Cut Position


Using a knife, cut off the lip of the rear engine oil seal.


b.

Using a screwdriver, pry out the rear engine oil seal.

NOTICE:

Do not damage the surface of the rear engine oil seal press fit hole or the crankshaft.


HINT:

Tape the screwdriver tip before use.