Home › Engine / Hybrid System › M15A-FKS (ENGINE MECHANICAL) › ENGINE UNIT › 2020.03–2020.07
RM36W0E _51 Engine / Hybrid System _087837 M15A-FKS ENGINE MECHANICAL _0424630 ENGINE UNIT A

M15A-FKS ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 19100P 1.REMOVE SPARK PLUG

Hide 89448D 3.REMOVE OIL PRESSURE AND TEMPERATURE SENSOR

Hide 11102A 4.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11102A 5.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 15370 6.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side)

Hide 15370 7.INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side)

Hide 16031 8.INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Hide 16032 9.INSTALL WATER INLET WITH WATER PUMP HOUSING SUB-ASSEMBLY

Hide 12180E 10.REMOVE OIL FILLER CAP ASSEMBLY

a.
A458819

Remove the oil filler cap sub-assembly from the cylinder head cover sub-assembly.


Hide 12108A 11.REMOVE OIL FILLER CAP GASKET

a.
A366042

Remove the oil filler cap gasket from the oil filler cap sub-assembly.


Hide 11401G 12.REMOVE CRANKSHAFT POSITION SENSOR

Hide 12204C 13.REMOVE PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

Hide 29300 14.REMOVE VACUUM PUMP ASSEMBLY

Hide 13470 15.REMOVE CRANKSHAFT PULLEY ASSEMBLY

a.
A458820C01
1.042,1.104 0.573,1.073 0.573,1.073 0.813,0.646 false 0.083,0.146 0.26,0.354 0.177,0.208 10 true *a 2.438,1.896 2.656,2.115 0.219,0.219 10 true *b 0.25,1.01 0.708,1.208 0.458,0.198 10 false SST
*a Hold
*b Turn


Using SST, hold the crankshaft pulley assembly and loosen the crankshaft pulley set bolt. Further loosen the crankshaft pulley set bolt until 2 or 3 threads remain screwed into the crankshaft.

SST
09213-54015  
09330-00021  


b.
A458821C01
1.313,1.135 1.5,1.135 false 2.052,0.188 2.167,0.188 2.167,0.188 2.198,0.635 true 1.896,0.115 2.208,0.313 0.313,0.198 10 false *1 1.021,1.042 1.479,1.24 0.458,0.198 10 false SST 0.073,2.01 0.385,2.208 0.313,0.198 10 false *a 0.927,3.146 1.25,3.344 0.323,0.198 10 false *b
*1 Crankshaft Pulley Set Bolt
*a Hold
*b Turn


Using SST and the crankshaft pulley set bolt, remove the crankshaft pulley assembly and crankshaft pulley set bolt.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05070, 09957-04010)

HINT:

Apply lubricant to the threads and end of SST.



Hide 16304 16.REMOVE OUTLET WATER SUB-ASSEMBLY

a.
A458822

Using an 8 mm socket wrench, remove the 2 bolts, outlet water sub-aseembly and water outlet gasket from the cylinder head sub-assembly.


Hide 16305E 17.REMOVE OUTLET WATER BY-PASS SUB-ASSEMBLY

a.
A458823

Using an 8 mm socket wrench, remove the 2 bolts, outlet water by-pass sub-assembly and outlet water pipe gasket from the cylinder head sub-assembly.


Hide 11201 18.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A458824

Using an 8 mm socket wrench, remove the 13 bolts and cylinder head cover sub-assembly from the camshaft housing sub-assembly.


b.
A458825

Remove the 5 cylinder head cover gaskets from the cylinder head cover sub-assembly.


c.
A458826

Remove the camshaft bearing cap oil hole gasket from the No. 1 camshaft bearing cap.


Hide 11193 19.REMOVE SPARK PLUG TUBE GASKET

a.
A458827C01
2.031,0.594 1.865,0.594 1.865,0.594 1.542,0.885 true 2.094,0.51 2.313,0.698 0.219,0.188 10 true *a
*a Protective Tape


Using a screwdriver, pry out the 3 spark plug tube gaskets from the cylinder head cover sub-assembly.

NOTICE:

Be careful not to damage the cylinder head cover sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 12315A 20.REMOVE ENGINE MOUNTING BRACKET RH

a.
A458828

Remove the 3 bolts and engine mounting bracket RH from the No. 2 timing chain cover assembly.


Hide 11320B 21.REMOVE NO. 2 TIMING CHAIN COVER ASSEMBLY

Hide 11301C 22.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 13519 23.REMOVE OIL PUMP DRIVE GEAR

a.
A465641

Remove the oil pump drive gear from the crankshaft.


Hide 24.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

a.

Temporarily install the crankshaft pulley bolt.

A466040C01
2.073,5.438 3.188,5.135 true 0.417,2.833 1.406,2.125 true 0.417,2.833 1.354,2.479 true 6.75,3 5.615,2.104 true 6.75,3 5.667,2.552 true 1.052,0.271 1.365,0.469 0.313,0.198 10 false *a 5.521,0.188 5.833,0.385 0.313,0.198 10 false *b 2.906,4.344 3.219,4.542 0.313,0.198 10 false *c 1.865,5.396 2.177,5.594 0.313,0.198 10 false *1 0.219,2.792 0.479,3 0.26,0.208 10 false *d 6.792,2.938 7.052,3.125 0.26,0.188 10 true *d
*1 Crankshaft Timing Gear Key - -
*a Approximately 45.32° *b Approximately 16.89°
*c Approximately 95° *d Timing Mark



b.

Rotate the crankshaft clockwise and align the crankshaft timing gear key as shown in the illustration.


c.

Check that the timing marks on the camshaft timing exhaust gear assembly and camshaft timing gear assembly are as shown in the illustration.


d.

Remove the crankshaft pulley bolt.

HINT:

As the exhaust camshaft sub-assembly may rotate counterclockwise strongly when the crankshaft pulley bolt is removed, use a wrench to hold the hexagonal portion of the exhaust camshaft sub-assembly.



Hide 13050 25.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A458831C01
1.615,1.26 1.906,0.917 1.906,0.917 2.063,0.917 true 2.125,0.813 2.438,1.01 0.313,0.198 10 true *a
*a Loosen
V113147

Turn


Hold the hexagonal portion of the exhaust camshaft sub-assembly with a wrench and turn the camshaft timing gear assembly clockwise to loosen the chain sub-assembly between the camshaft timing exhaust gear assembly and camshaft timing gear assembly.


b.
A458832C01
2.063,0.792 2.479,0.375 true 2.531,0.219 2.75,0.427 0.219,0.208 10 true *a
*a Hexagon Wrench


Push the plunger all the way in then insert the 1.5 mm hexagon wrench into the No. 1 chain tensioner assembly hole.


c.
A458833C01
1.885,0.219 2.198,0.417 0.313,0.198 10 false *a
*a Hold
V113147

Turn


Using a wrench, hold the hexagonal portion of the intake camshaft sub-assembly.

NOTICE:
·

Be careful not to damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube with the wrench.

·

Do not disassemble the camshaft timing gear assembly.




d.

Using a 10 mm bi-hexagonal wrench, remove the bolt and camshaft timing gear assembly from the intake camshaft sub-assembly.


Hide 13506 26.REMOVE CHAIN SUB-ASSEMBLY

a.
A458834

Remove the crankshaft timing sprocket and chain sub-assembly.


Hide 13540 27.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A466464C01
0.031,0.031 0.406,0.271 0.375,0.24 12 false *A 0.052,2.333 0.427,2.573 0.375,0.24 12 false *B
*A w/ Stud Bolt
*B w/o Stud Bolt


w/ Stud Bolt:

i.

Remove the bolt.


ii.

Remove the nut and No. 1 chain tensioner assembly from the timing chain cover assembly.



b.

w/o Stud Bolt:

i.

Remove the 2 bolts and No. 1 chain tensioner assembly from the timing chain cover assembly.



Hide 13559 28.REMOVE CHAIN TENSIONER SLIPPER

a.
A458836

Remove the bolt and chain tensioner slipper from the timing chain cover assembly.


Hide 13561 29.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A458837

Remove the 2 bolts and No. 1 chain vibration damper from the timing chain cover assembly.


Hide 13070A 30.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A458838

Using a wrench, hold the hexagonal portion of the exhaust camshaft sub-assembly.

NOTICE:

Be careful not to damage the camshaft housing sub-assembly, cylinder head sub-assembly or spark plug tube with the wrench.



b.

Using a 5 mm hexagon socket wrench, remove the 3 bolts.


c.
A458839C01
0.875,0.427 1.021,0.427 1.021,0.427 1.229,0.896 false 1,1.833 0.833,1.833 0.833,1.833 0.667,1.385 false 0.677,0.302 0.99,0.5 0.313,0.198 10 false *1 1.073,1.74 1.385,1.938 0.313,0.198 10 false *2
*1 Camshaft Timing Exhaust Gear Assembly
*2 Camshaft Timing Oil Control Valve Assembly (Exhaust Camshaft Timing Gear Bolt Assembly)


Remove the camshaft timing exhaust gear assembly and camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly) from the exhaust camshaft sub-assembly.


Hide 11310 31.REMOVE TIMING CHAIN COVER ASSEMBLY

a.
A458840

Remove the 20 bolts and timing chain cover assembly from the camshaft housing sub-assembly, cylinder head sub-assembly, cylinder block sub-assembly, stiffening crankcase assembly and oil pump assembly.


b.

Remove the timing chain cover assembly by prying between the cylinder head sub-assembly, camshaft housing sub-assembly, cylinder block sub-assembly and stiffening crankcase assembly with a screwdriver with its tip wrapped with protective tape.

A465643C01
2.031,2.396 1.625,2.229 1.625,2.229 1.938,1.979 true 1.292,4.073 1.75,3.615 true 6.021,1.135 6.229,0.938 true 6.021,2.448 6.229,2.25 true 6.167,3.875 5.938,4.146 true 1.375,2.156 1.573,2.344 0.198,0.188 10 true *a 1.125,4.021 1.438,4.219 0.313,0.198 10 false *a 6.292,0.792 6.5,0.99 0.208,0.198 10 true *a 6.26,2.135 6.469,2.333 0.208,0.198 10 true *a 5.813,4.146 6.021,4.344 0.208,0.198 10 true *a
*a Protective Tape - -


NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly, camshaft housing sub-assembly, cylinder block sub-assembly, stiffening crankcase assembly and timing chain cover assembly.



Hide 13631 32.REMOVE BALANCESHAFT DRIVE GEAR

a.
A458995

Remove the balanceshaft drive gear from the crankshaft.


Hide 13471A 33.REMOVE CRANKSHAFT TIMING GEAR KEY

a.
A458843C01
0.917,1.24 0.542,0.781 0.542,0.781 0.385,0.781 true 0.125,0.656 0.344,0.854 0.219,0.198 10 true *a
*a Protective Tape


Using a screwdriver, remove the 2 crankshaft timing gear keys from the crankshaft.

HINT:

Tape the screwdriver tip before use.



Hide 23477 34.REMOVE FUEL PUMP LIFTER GUIDE

a.
A458844

Using an 8 mm socket wrench, remove the 2 bolts and fuel pump lifter guide from the No. 4 camshaft bearing cap.


Hide 11103 35.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A458845N01
0.583,1.823 0.74,2.031 0.156,0.208 10 true 2 0.542,0.146 0.677,0.385 0.135,0.24 10 true 1 0.427,0.948 0.583,1.146 0.156,0.198 10 true 3 2.844,0.24 3,0.438 0.156,0.198 10 true 4 2.906,0.958 3.063,1.156 0.156,0.198 10 true 5 2.063,0.146 2.208,0.333 0.146,0.188 10 true 6 2.698,1.771 2.833,1.979 0.135,0.208 10 true 7 1.969,1.271 2.094,1.438 0.125,0.167 10 true 8 1.844,0.115 1.99,0.292 0.146,0.177 10 true 9 1.802,1.875 2.021,2.042 0.219,0.167 10 true 10 1.396,1.302 1.604,1.521 0.208,0.219 10 true 11 1.313,0.104 1.531,0.271 0.219,0.167 10 true 12 1.302,1.875 1.531,2.073 0.229,0.198 10 true 13 0.906,1.302 1.104,1.5 0.198,0.198 10 true 14

Uniformly loosen and remove the 14 bolts in the order shown in the illustration.


b.
A458846

Remove the camshaft housing sub-assembly by prying between the cylinder head sub-assembly and camshaft housing sub-assembly with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly and camshaft housing sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 36.REMOVE CAMSHAFT BEARING CAP

a.
A458847C01
0.844,1.49 0.479,1.771 true 1.385,1.594 1.385,1.938 true 1.885,1.583 1.885,1.927 true 2.875,1.396 2.594,1.094 true 0.281,1.729 0.531,1.917 0.25,0.188 10 false *1 1.323,1.979 1.635,2.135 0.313,0.156 10 false *2 2.917,1.344 3.156,1.573 0.24,0.229 10 false *4 1.823,1.969 2.135,2.125 0.313,0.156 10 false *3 0.552,1.344 0.719,1.531 0.167,0.188 10 false 1 2.01,1.688 2.177,1.896 0.167,0.208 10 true 2 2.104,0.792 2.271,0.979 0.167,0.188 10 true 3 1.083,0.552 1.25,0.74 0.167,0.188 10 true 4 1.031,1.344 1.198,1.531 0.167,0.188 10 true 5 1.563,0.573 1.729,0.76 0.167,0.188 10 true 6 1.521,1.344 1.688,1.531 0.167,0.188 10 true 7
*1 No. 1 Camshaft Bearing Cap
*2 No. 2 Camshaft Bearing Cap
*3 No. 3 Camshaft Bearing Cap
*4 No. 4 Camshaft Bearing Cap


Remove the 7 bolts in the order shown in the illustration.


b.

Remove the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, 2 No. 3 camshaft bearing caps and No. 4 camshaft bearing cap from the camshaft housing sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13501A 37.REMOVE INTAKE CAMSHAFT SUB-ASSEMBLY

a.
A458848

Remove the intake camshaft sub-assembly from the camshaft housing sub-assembly.


Hide 13502B 38.REMOVE EXHAUST CAMSHAFT SUB-ASSEMBLY

a.
A458849

Remove the exhaust camshaft sub-assembly from the camshaft housing sub-assembly.


Hide 13801 39.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A458850

Remove the 12 No. 1 valve rocker arm sub-assemblies from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13750 40.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.
A458851

Remove the 12 valve lash adjuster assemblies from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13716 41.REMOVE VALVE STEM CAP

a.
A458852

Remove the 12 valve stem caps from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 11101 42.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A458853C01
2.688,0.479 2.844,0.677 0.156,0.198 10 true 1 0.656,1.667 0.813,1.865 0.156,0.198 10 true 2 0.604,0.417 0.75,0.594 0.146,0.177 10 true 3 2.677,1.635 2.833,1.833 0.156,0.198 10 true 4 1.385,0.302 1.542,0.5 0.156,0.198 10 true 5 1.865,1.771 2.021,1.969 0.156,0.198 10 true 6 1.885,0.313 2.042,0.51 0.156,0.198 10 true 7 1.375,1.771 1.531,1.969 0.156,0.198 10 true 8
V100136

Front of Engine


Using a 12 mm socket wrench, uniformly loosen the 8 cylinder head set bolts in the order shown in the illustration. Remove the 8 cylinder head set bolts and 8 plate washers.

NOTICE:
·

Be careful not to drop the plate washers into the cylinder head sub-assembly.

·

Warpage or cracking of the cylinder head sub-assembly may result from removing the cylinder head set bolts in the incorrect order.



HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



b.

Remove the cylinder head sub-assembly from the cylinder block sub-assembly.


Hide 11445 44.REMOVE CYLINDER BLOCK WATER JACKET SPACER

a.
A458854

Remove the cylinder block water jacket spacer from the cylinder block sub-assembly.

NOTICE:

Be sure to remove the cylinder block water jacket spacer. If it is not removed, it may fall and become damaged when the cylinder block sub-assembly is inverted.



Hide 15601 45.REMOVE OIL FILTER SUB-ASSEMBLY

Hide 15600A 46.REMOVE OIL FILTER UNION

A458855

a.

Using a 12 mm hexagon socket wrench, remove the oil filter union from the stiffening crankcase assembly.


Hide 12101A 47.REMOVE OIL PAN DRAIN PLUG

a.

Remove the oil pan drain plug and gasket from the oil pan sub-assembly.


Hide 12101 48.REMOVE OIL PAN SUB-ASSEMBLY

a.
A458856C01
2.115,1.979 2.344,2.177 0.229,0.198 10 true *a 1.219,1.896 1.448,2.094 0.229,0.198 10 false *a
*a Nut


Remove the 9 bolts and 2 nuts.


b.
A118769

Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and stiffening crankcase assembly, cut through the applied sealer and remove the oil pan sub-assembly.

NOTICE:
·

Be careful not to damage the contact surfaces of the stiffening crankcase assembly and oil pan sub-assembly.

·

Be careful not to damage the oil pan sub-assembly flange.




Hide 15104 49.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A458857

Using an 8 mm socket wrench, remove the bolt, oil strainer sub-assembly and oil strainer gasket from the stiffening crankcase assembly.


Hide 89491 50.REMOVE ENGINE OIL LEVEL SENSOR

Hide 11420 51.REMOVE STIFFENING CRANKCASE ASSEMBLY

a.
A458858

Remove the 8 bolts.


b.
A458859

Using a screwdriver, remove the stiffening crankcase assembly by prying between the stiffening crankcase assembly and cylinder block sub-assembly at the places shown in the illustration.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and stiffening crankcase assembly.


HINT:

Tape the screwdriver tip before use.



Hide 12121 52.REMOVE NO. 1 OIL PAN BAFFLE PLATE

a.
A458987

Remove the 5 bolts and No. 1 oil pan baffle plate from the stiffening crankcase assembly.


Hide 13620B 53.REMOVE ENGINE BALANCER ASSEMBLY

a.
A458986

Remove the 4 bolts and engine balancer assembly from the stiffening crankcase assembly.


Hide 54.REMOVE STRAIGHT SCREW PLUG

a.
A459773

Using a 10 mm hexagon socket wrench, remove the straight screw plug and gasket from the stiffening crankcase assembly.


Hide 55.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


Hide 56.REMOVE RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.


Hide 57.REMOVE STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pins unless they are being replaced.


Hide 11401L 58.REMOVE REAR ENGINE OIL SEAL

a.
A458865

Remove the rear engine oil seal from the cylinder block sub-assembly.